linux-stable.git/drivers/net/phy/phy_device.c, branch linux-5.0.y

net: phy: improve genphy_soft_reset

2019-05-31T13:44:58+00:00

[ Upstream commit 8c90b795e90f7753d23c18e8b95dd71b4a18c5d9 ]

PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.

So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.

BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.

Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: fix phy_validate_pause

2019-05-16T17:40:29+00:00

[ Upstream commit b4010af981ac8cdf1f7f58eb6b131c482e5dee02 ]

We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.

See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes

The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.

Fixes: 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: consider latched link-down status in polling mode

2019-04-05T20:34:41+00:00

[ Upstream commit 93c0970493c71f264e6c3c7caf1ff24a9e1de786 ]

The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.

On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:

- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
  down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
  Interrupt handler reads link status, means it reads the latched
  "link is down" info. But there won't be another interrupt as long
  as link stays up, therefore phylib will never recognize that link
  is up.

Deal with both scenarios by reading the register twice in interrupt
mode only.

Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: don't clear BMCR in genphy_soft_reset

2019-04-03T04:27:26+00:00

[ Upstream commit d29f5aa0bc0c321e1b9e4658a2a7e08e885da52a ]

So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.

[0] https://marc.info/?t=155264050700001&r=1&w=2

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid 
Tested-by: liweihang 
Signed-off-by: Heiner Kallweit 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: phy driver features are mandatory

2019-01-19T18:03:08+00:00

Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.

Prevent the phy driver from registering if the features field is missing.

Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood 
Signed-off-by: Camelia Groza 
Signed-off-by: David S. Miller

net: phy: Add missing features to PHY drivers

2019-01-16T23:41:02+00:00

The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.

Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood 
Reported-by: Camelia Groza 
Signed-off-by: Andrew Lunn 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2018-12-20T19:53:36+00:00

Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.

Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.

Signed-off-by: David S. Miller

net: phy: Fix the issue that netif always links up after resuming

2018-12-19T05:48:15+00:00

Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.

If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.

In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.

This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().

Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit 
Signed-off-by: Kunihiko Hayashi 
Signed-off-by: David S. Miller

net: phy: remove unused code in phy_probe

2018-12-19T05:38:12+00:00

3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.

Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

net: mii: Add mii_lpa_mod_linkmode_lpa_t

2018-12-06T00:26:16+00:00

Add a _mod_ variant of mii_lpa_to_linkmode_lpa_t. Use this to fix the
genphy_read_status() where the 1G link partner features are getting
lost.

Fixes: c0ec3c273677 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit 
Signed-off-by: Andrew Lunn 
Signed-off-by: David S. Miller