linux-stable.git/drivers/net/phy/phy-c45.c, branch linux-rolling-lts Linux kernel stable tree net: phy: skip EEE advertisement write when autoneg is disabled 2026-06-01T15:50:42+00:00 Nerijus Bendžiūnas nerijus.bendziunas@gmail.com 2026-05-16T15:02:51+00:00 49eff79967fd6ea45a9d028710bb852c950baef9 commit 960e77ce14a83ef7f226e8e4b4d75765633ba48b upstream. genphy_c45_an_config_eee_aneg() writes the EEE advertisement to the auto-negotiation device's MMD register space (MDIO_MMD_AN, register MDIO_AN_EEE_ADV). These registers are read by the link partner only during auto-negotiation, so writing them while autoneg is disabled cannot influence the link. On some PHYs (e.g. Broadcom BCM54213PE) the write nevertheless reaches the chip and disturbs the receive datapath. Concretely, running ethtool -s eth0 speed 100 duplex full autoneg off ethtool --set-eee eth0 eee off leaves eth0 with TX working and RX completely silent on a Raspberry Pi 4 / CM4 board (bcmgenet + BCM54213PE in rgmii-rxid). Switching back to autoneg recovers the link. Prior to commit f26a29a038ee ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled"), the disable path was effectively a no-op because the helper read the stale eee_cfg.eee_enabled, so the underlying PHY behavior never surfaced. Bisected on rpi-6.12.y between commits 83943264 (good) and effcbc88 (bad) to f26a29a038ee. Fixes: f26a29a038ee ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled") Cc: stable@vger.kernel.org Signed-off-by: Nerijus Bendžiūnas <nerijus.bendziunas@gmail.com> Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de> Tested-by: Nicolai Buchwitz <nb@tipi-net.de> Link: https://patch.msgid.link/20260516150251.879680-1-nerijus.bendziunas@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 960e77ce14a83ef7f226e8e4b4d75765633ba48b upstream.

genphy_c45_an_config_eee_aneg() writes the EEE advertisement to the
auto-negotiation device's MMD register space (MDIO_MMD_AN, register
MDIO_AN_EEE_ADV).  These registers are read by the link partner only
during auto-negotiation, so writing them while autoneg is disabled
cannot influence the link.  On some PHYs (e.g. Broadcom BCM54213PE)
the write nevertheless reaches the chip and disturbs the receive
datapath.

Concretely, running

    ethtool -s eth0 speed 100 duplex full autoneg off
    ethtool --set-eee eth0 eee off

leaves eth0 with TX working and RX completely silent on a
Raspberry Pi 4 / CM4 board (bcmgenet + BCM54213PE in rgmii-rxid).
Switching back to autoneg recovers the link.

Prior to commit f26a29a038ee ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled"),
the disable path was effectively a no-op because the helper read
the stale eee_cfg.eee_enabled, so the underlying PHY behavior never
surfaced.

Bisected on rpi-6.12.y between commits 83943264 (good) and
effcbc88 (bad) to f26a29a038ee.

Fixes: f26a29a038ee ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled")
Cc: stable@vger.kernel.org
Signed-off-by: Nerijus Bendžiūnas <nerijus.bendziunas@gmail.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260516150251.879680-1-nerijus.bendziunas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: phy: move definition of genphy_c45_driver to phy_device.c 2025-06-13T01:23:08+00:00 Heiner Kallweit hkallweit1@gmail.com 2025-06-10T21:34:53+00:00 00ee2537255e25a14360288dbd94ff62c0db497d genphy_c45_read_status() is exported, so we can move definition of genphy_c45_driver to phy_device.c and make it static. This helps to clean up phy.h a little. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/ead3ab17-22d0-4cd3-901c-3d493ab851e6@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
genphy_c45_read_status() is exported, so we can move definition of
genphy_c45_driver to phy_device.c and make it static. This helps
to clean up phy.h a little.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ead3ab17-22d0-4cd3-901c-3d493ab851e6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: fix genphy_c45_eee_is_active() for disabled EEE 2025-03-21T20:38:36+00:00 Russell King (Oracle) rmk+kernel@armlinux.org.uk 2025-03-16T11:51:11+00:00 4b9235a880f13ae3443465192603b298a603b2c5 Commit 809265fe96fe ("net: phy: c45: remove local advertisement parameter from genphy_c45_eee_is_active") stopped reading the local advertisement from the PHY earlier in this development cycle, which broke "ethtool --set-eee ethX eee off". When ethtool is used to set EEE off, genphy_c45_eee_is_active() indicates that EEE was active if the link partner reported an advertisement, which causes phylib to set phydev->enable_tx_lpi on link up, despite our local advertisement in hardware being empty. However, phydev->advertising_eee is preserved while EEE is turned off, which leads to genphy_c45_eee_is_active() incorrectly reporting that EEE is active. Fix it by checking phydev->eee_cfg.eee_enabled, and if clear, immediately indicate that EEE is not active. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/E1ttmWN-0077Mb-Q6@rmk-PC.armlinux.org.uk Signed-off-by: Paolo Abeni <pabeni@redhat.com> 
Commit 809265fe96fe ("net: phy: c45: remove local advertisement
parameter from genphy_c45_eee_is_active") stopped reading the local
advertisement from the PHY earlier in this development cycle, which
broke "ethtool --set-eee ethX eee off".

When ethtool is used to set EEE off, genphy_c45_eee_is_active()
indicates that EEE was active if the link partner reported an
advertisement, which causes phylib to set phydev->enable_tx_lpi on
link up, despite our local advertisement in hardware being empty.
However, phydev->advertising_eee is preserved while EEE is turned off,
which leads to genphy_c45_eee_is_active() incorrectly reporting that
EEE is active.

Fix it by checking phydev->eee_cfg.eee_enabled, and if clear,
immediately indicate that EEE is not active.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1ttmWN-0077Mb-Q6@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: phy: Allow loopback speed selection for PHY drivers 2025-03-20T07:45:08+00:00 Gerhard Engleder gerhard@engleder-embedded.com 2025-03-12T20:30:06+00:00 45456e38c44eda2f1285601398fd289b3cec7002 PHY drivers support loopback mode, but it is not possible to select the speed of the loopback mode. The speed is chosen by the set_loopback() operation of the PHY driver. Same is valid for genphy_loopback(). There are PHYs that support loopback with different speeds. Extend set_loopback() to make loopback speed selection possible. Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250312203010.47429-2-gerhard@engleder-embedded.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> 
PHY drivers support loopback mode, but it is not possible to select the
speed of the loopback mode. The speed is chosen by the set_loopback()
operation of the PHY driver. Same is valid for genphy_loopback().

There are PHYs that support loopback with different speeds. Extend
set_loopback() to make loopback speed selection possible.

Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250312203010.47429-2-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: phy: add phylib-internal.h 2025-02-25T03:14:31+00:00 Heiner Kallweit hkallweit1@gmail.com 2025-02-22T08:36:10+00:00 a3e51d4711793be001220784bd7d8ce81517003e This patch is a starting point for moving phylib-internal declarations to a private header file. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://patch.msgid.link/082eacd2-a888-4716-8797-b3491ce02820@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
This patch is a starting point for moving phylib-internal
declarations to a private header file.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/082eacd2-a888-4716-8797-b3491ce02820@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: c45: remove local advertisement parameter from genphy_c45_eee_is_active 2025-02-19T02:07:09+00:00 Heiner Kallweit hkallweit1@gmail.com 2025-02-16T21:20:07+00:00 809265fe96fe3eb7a85a9260356767587c482cb7 After the last user has gone, we can remove the local advertisement parameter from genphy_c45_eee_is_active. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/bd121330-9e28-4bc8-8422-794bd54d561f@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
After the last user has gone, we can remove the local advertisement
parameter from genphy_c45_eee_is_active.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/bd121330-9e28-4bc8-8422-794bd54d561f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: c45: use cached EEE advertisement in genphy_c45_ethtool_get_eee 2025-02-19T02:07:09+00:00 Heiner Kallweit hkallweit1@gmail.com 2025-02-16T21:19:23+00:00 199d0ce385adbbf5b8532752a26e12413100c4ea Now that disabled EEE modes are considered when populating advertising_eee, we can use this bitmap here instead of reading the PHY register. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/e57ed3d4-d0bc-4f91-83f6-8f48dfb6d7d7@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Now that disabled EEE modes are considered when populating
advertising_eee, we can use this bitmap here instead of reading
the PHY register.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/e57ed3d4-d0bc-4f91-83f6-8f48dfb6d7d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: c45: Don't silently remove disabled EEE modes any longer when writing advertisement register 2025-02-19T02:07:09+00:00 Heiner Kallweit hkallweit1@gmail.com 2025-02-16T21:18:42+00:00 aa951feb542662342223c8db582897969b64fb59 advertising_eee is adjusted now whenever an EEE mode gets disabled. Therefore we can remove the silent removal of disabled EEE modes here. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/e95b9dad-24a7-4e3e-9af9-6f0770cf1520@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
advertising_eee is adjusted now whenever an EEE mode gets disabled.
Therefore we can remove the silent removal of disabled EEE modes here.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/e95b9dad-24a7-4e3e-9af9-6f0770cf1520@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: c45: improve handling of disabled EEE modes in generic ethtool functions 2025-02-15T03:46:12+00:00 Heiner Kallweit hkallweit1@gmail.com 2025-02-12T20:01:42+00:00 0025fa45253c266eb3424d0f21e240c8c420894a Currently disabled EEE modes are shown as supported in ethtool. Change this by filtering them out when populating data->supported in genphy_c45_ethtool_get_eee. Disabled EEE modes are silently filtered out by genphy_c45_write_eee_adv. This is planned to be removed, therefore ensure in genphy_c45_ethtool_set_eee that disabled EEE modes are removed from the user space provided EEE advertisement. For now keep the current behavior to do this silently. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://patch.msgid.link/5187c86d-9a5a-482c-974f-cc103ce9738c@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Currently disabled EEE modes are shown as supported in ethtool.
Change this by filtering them out when populating data->supported
in genphy_c45_ethtool_get_eee.
Disabled EEE modes are silently filtered out by genphy_c45_write_eee_adv.
This is planned to be removed, therefore ensure in
genphy_c45_ethtool_set_eee that disabled EEE modes are removed from the
user space provided EEE advertisement. For now keep the current behavior
to do this silently.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/5187c86d-9a5a-482c-974f-cc103ce9738c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: rename eee_broken_modes to eee_disabled_modes 2025-02-11T23:19:10+00:00 Heiner Kallweit hkallweit1@gmail.com 2025-02-10T20:49:22+00:00 8eb0d381be31bfa01f768ad38a15af7ade805e69 This bitmap is used also if the MAC doesn't support an EEE mode. So the mode isn't necessarily broken in the PHY. Therefore rename the bitmap. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/6cd11422-dd67-4c87-a642-308de694af92@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
This bitmap is used also if the MAC doesn't support an EEE mode.
So the mode isn't necessarily broken in the PHY. Therefore rename
the bitmap.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/6cd11422-dd67-4c87-a642-308de694af92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>