linux-stable.git/drivers/net/phy/micrel.c, branch linux-4.19.y

net: phy: micrel: Allow probing without .driver_data

2022-06-14T14:59:17+00:00

[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ]

Currently, if the .probe element is present in the phy_driver structure
and the .driver_data is not, a NULL pointer dereference happens.

Allow passing .probe without .driver_data by inserting NULL checks
for priv->type.

Signed-off-by: Fabio Estevam 
Reviewed-by: Andrew Lunn 
Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

phy: micrel: ksz8041nl: do not use power down mode

2021-11-26T10:36:10+00:00

[ Upstream commit 2641b62d2fab52648e34cdc6994b2eacde2d27c1 ]

Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.

Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.

Remove the suspend/resume callback to avoid using the power down mode
completely.

[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf

Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner 
Acked-by: Marcel Ziswiler 
Signed-off-by: Francesco Dolcini 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: micrel: kszphy_resume(): add delay after genphy_resume() before accessing PHY registers

2020-04-13T08:45:08+00:00

[ Upstream commit 6110dff776f7fa65c35850ef65b41d3b39e2fac2 ]

After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.

If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.

This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.

The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.

This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().

Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend")
Signed-off-by: Oleksij Rempel 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ9031

2020-01-27T13:50:13+00:00

[ Upstream commit 1d16073a326891c2a964e4cb95bc18fbcafb5f74 ]

So far genphy_soft_reset was used automatically if the PHY driver
didn't implement the soft_reset callback. This changed with the
mentioned commit and broke KSZ9031. To fix this configure the
KSZ9031 PHY driver to use genphy_soft_reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Reported-by: Tony Lindgren 
Signed-off-by: Heiner Kallweit 
Tested-by: Tony Lindgren 
Tested-by: Sekhar Nori 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

net: phy: Micrel KSZ8061: link failure after cable connect

2019-03-10T06:17:18+00:00

[ Upstream commit 232ba3a51cc224b339c7114888ed7f0d4d95695e ]

With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.

DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).

END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.

WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
   register 2, prior to connecting the cable or prior to setting the
   Restart Auto-negotiation bit in register 0h. The MMD registers are
   accessed via the indirect access registers Dh and Eh, or via the Micrel
   EthUtil utility as shown here:
   . if using the EthUtil utility (usually with a Micrel KSZ8061
     Evaluation Board), type the following commands:
     > address 1
     > mmd 1
     > iw 2 b61a
   . Alternatively, write the following registers to write to the
     indirect MMD register:
     Write register Dh, data 0001h
     Write register Eh, data 0002h
     Write register Dh, data 4001h
     Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
   either by the strapping option, or by clearing bit 12 in register 0h.
   Care must be taken to ensure that the KSZ8061 and the link partner
   will link with the same speed and duplex. Note that the KSZ8061
   defaults to full-duplex when auto-negotiation is off, but other
   devices may default to half-duplex in the event of failed
   auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
   or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
   be recovered by setting the Restart Auto-Negotiation bit in
   register 0h, or by resetting or power cycling the device. Reset may
   be either hardware reset or software reset (register 0h, bit 15).

PLAN
This errata will not be corrected in the future revision.

Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch 
Signed-off-by: Rajasingh Thavamani 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2018-05-21T20:01:54+00:00

S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.

TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.

The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.

Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.

Signed-off-by: David S. Miller

net: phy: micrel: add 125MHz reference clock workaround

2018-05-16T16:20:03+00:00

The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.

The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.

Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.

Signed-off-by: Markus Niebel 
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

drivers: net: replace UINT64_MAX with U64_MAX

2018-04-28T00:18:55+00:00

U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:

	#ifndef UINT64_MAX
	#define UINT64_MAX             (u64)(~((u64)0))
	#endif

I believe this is in one phy driver then copied and pasted to other phy
drivers.

Replace the UINT64_MAX with U64_MAX to clean up the source code.

Signed-off-by: Jisheng Zhang 
Signed-off-by: David S. Miller

net: phy: micrel: Use the general dummy stubs for MMD register access

2018-03-22T15:41:08+00:00

The new general dummy stubs for MMD register access were introduced.
Use that for the codes reuse.

Signed-off-by: Kevin Hao 
Signed-off-by: David S. Miller

net: phy: micrel: Use strlcpy() for ethtool::get_strings

2018-03-06T16:12:39+00:00

Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.

Fixes: 2b2427d06426 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller