linux-stable.git/drivers/net/igb, branch linux-2.6.28.y

driver/net/*: remove redundant argument comments

2008-11-23T23:46:55+00:00

remove redundant argument comments in files of drivers/net/*

Signed-off-by: Qinghuang Feng 
Signed-off-by: David S. Miller

igb: use dev_printk instead of printk

2008-11-16T09:42:36+00:00

Use dev_printk() instead of printk() to give a little more context
and use consistent format.

Signed-off-by: Bjorn Helgaas 
Signed-off-by: David S. Miller

igb: Use device_set_wakeup_enable

2008-11-16T09:35:57+00:00

Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol().  Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.

Signed-off-by: "Rafael J. Wysocki" 
Signed-off-by: Jeff Kirsher 
Signed-off-by: David S. Miller

igb: add IGB_DCA instead of selecting INTEL_IOATDMA

2008-10-22T10:54:07+00:00

Add a bool IGB_DCA defined to y if IGB and DCA are enabled, but IGB isn't y while DCA=m.  And thus remove the need to select INTEL_IOATDMA when IGB is enabled, so that non-x86 architectures can build the igb driver.
Based on work/patch from Brice Goglin 

Signed-off-by: Jeff Kirsher 
Signed-off-by: Jeff Garzik

igb: fix tx data corruption with transition to L0s on 82575

2008-10-22T10:53:59+00:00

The 82575 has an issue in which the DMA will go out of sync if the link
partner goes into an L0s state.  To prevent this we set the pci-e link
partner capability bits to disable the L0s transition on the hw.

Signed-off-by: Alexander Duyck 
Signed-off-by: Jeff Kirsher 
Signed-off-by: Jeff Garzik

igb: clean up a stray fake netdev code left in rx path

2008-09-03T14:08:17+00:00

Remove code that was in place to support fake netdev

Signed-off-by: Alexander Duyck 
Signed-off-by: Jeff Kirsher 
Signed-off-by: Jeff Garzik

igb: remove unneeded cleaned variable in clean_tx_irq path

2008-09-03T14:08:16+00:00

The cleaned variable can be replaced by the count of packets cleaned during
the tx interrupt routine so it can be removed.

Signed-off-by: Alexander Duyck 
Signed-off-by: Jeff Kirsher 
Signed-off-by: Jeff Garzik

igb: remove 82576 quad adapter

2008-08-27T09:36:12+00:00

Disable support for device 8086:10E8.  Currently the result of loading the
driver with the device present causes system instability.

Signed-off-by: Alexander Duyck 
Signed-off-by: Jeff Kirsher 
Signed-off-by: Jeff Garzik

igb: fix setting the number of tx queues

2008-08-27T09:16:31+00:00

The real_num_tx_queues was not being set when in MSI-X only mode.  This patch
corrects that path so all interrupt types are correctly configured.

Signed-off-by: Alexander Duyck 
Signed-off-by: Jeff Kirsher 
Signed-off-by: Jeff Garzik

igb: ethtool -d reads EICR which is incorrect as it is read on clear

2008-08-27T09:16:30+00:00

Ethtool -d is reading the EICR and ICR registers which is currently
clearing these registers and masking off interrupts.  To prevent this we
read the EICS and ICS equivilents as they can be read without clearing or
masking.

Signed-off-by: Alexander Duyck 
Signed-off-by: Jeff Kirsher 
Signed-off-by: Jeff Garzik