linux-stable.git/drivers/net/ieee802154, branch linux-rolling-stable Linux kernel stable tree ieee802154: ca8210: fix pointer truncation in kfifo on 64-bit 2026-07-24T14:21:16+00:00 Shitalkumar Gandhi shital.gandhi45@gmail.com 2026-05-20T10:57:50+00:00 d8ce67fa6a5e6929f5414e933ff9665176c2bce6 commit 6d7f7bcf225b2d566176bf6229dbd1252940cb3c upstream. ca8210_test_int_driver_write() and ca8210_test_int_user_read() exchange a kmalloc'd buffer pointer through a struct kfifo, but pass a literal '4' as the byte count to kfifo_in()/kfifo_out(). This is correct on 32-bit (pointer = 4 bytes), but on 64-bit only the low 4 bytes of the 8-byte pointer are written into the FIFO. The reader then reads back 4 bytes into an 8-byte local pointer variable, leaving the upper 4 bytes uninitialized stack data. The first dereference of the reconstructed pointer (fifo_buffer[1]) accesses an arbitrary kernel address and generally results in an oops. Use sizeof(fifo_buffer) so the byte count matches pointer width on every architecture. The driver has no architecture restriction in Kconfig, so any 64-bit build with CONFIG_IEEE802154_CA8210_DEBUGFS=y is exposed. Issue has been latent since the driver was added in 2017 because it is most commonly deployed on 32-bit MCUs. Found via a custom Coccinelle semantic patch hunting for short-byte kfifo I/O on byte-mode kfifos used to shuttle pointers. Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver") Cc: stable@vger.kernel.org Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/20260520105750.30144-1-shitalkumar.gandhi@cambiumnetworks.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 6d7f7bcf225b2d566176bf6229dbd1252940cb3c upstream.

ca8210_test_int_driver_write() and ca8210_test_int_user_read() exchange
a kmalloc'd buffer pointer through a struct kfifo, but pass a literal
'4' as the byte count to kfifo_in()/kfifo_out().

This is correct on 32-bit (pointer = 4 bytes), but on 64-bit only the
low 4 bytes of the 8-byte pointer are written into the FIFO. The reader
then reads back 4 bytes into an 8-byte local pointer variable, leaving
the upper 4 bytes uninitialized stack data. The first dereference of
the reconstructed pointer (fifo_buffer[1]) accesses an arbitrary kernel
address and generally results in an oops.

Use sizeof(fifo_buffer) so the byte count matches pointer width on every
architecture.

The driver has no architecture restriction in Kconfig, so any 64-bit
build with CONFIG_IEEE802154_CA8210_DEBUGFS=y is exposed. Issue has
been latent since the driver was added in 2017 because it is most
commonly deployed on 32-bit MCUs.

Found via a custom Coccinelle semantic patch hunting for short-byte
kfifo I/O on byte-mode kfifos used to shuttle pointers.

Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/20260520105750.30144-1-shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ieee802154: ca8210: fix cas_ctl leak on spi_async failure 2026-07-24T14:21:15+00:00 Shitalkumar Gandhi shital.gandhi45@gmail.com 2026-04-21T07:32:59+00:00 7e3630fbb6aabb844bbf35746dee0bf3894100c7 commit e09390e439bd7cca30dd10893b1f64802961667a upstream. ca8210_spi_transfer() allocates cas_ctl with kzalloc_obj(GFP_ATOMIC) and relies entirely on the SPI completion callback ca8210_spi_transfer_complete() to free it. The spi_async() API only invokes the completion callback on successful submission. On failure it returns a negative error code without ever queuing the callback, which leaves cas_ctl and its embedded spi_message and spi_transfer orphaned. Every kfree(cas_ctl) in the driver is inside the completion callback, so there is no other reclamation path. ca8210_spi_transfer() is called from ca8210_spi_exchange(), the interrupt handler ca8210_interrupt_handler(), and from the retry path inside the completion callback itself. The exchange and interrupt handler paths loop on -EBUSY, so under sustained SPI bus contention every retry iteration leaks a fresh cas_ctl (~600 bytes per occurrence). Fix it by freeing cas_ctl on the spi_async() error path. While here, correct the misleading error string: the function calls spi_async(), not spi_sync(). Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver") Cc: stable@vger.kernel.org Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/20260421073259.2259783-1-shitalkumar.gandhi@cambiumnetworks.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e09390e439bd7cca30dd10893b1f64802961667a upstream.

ca8210_spi_transfer() allocates cas_ctl with kzalloc_obj(GFP_ATOMIC)
and relies entirely on the SPI completion callback
ca8210_spi_transfer_complete() to free it.

The spi_async() API only invokes the completion callback on successful
submission.  On failure it returns a negative error code without ever
queuing the callback, which leaves cas_ctl and its embedded spi_message
and spi_transfer orphaned.  Every kfree(cas_ctl) in the driver is
inside the completion callback, so there is no other reclamation path.

ca8210_spi_transfer() is called from ca8210_spi_exchange(), the
interrupt handler ca8210_interrupt_handler(), and from the retry path
inside the completion callback itself.  The exchange and interrupt
handler paths loop on -EBUSY, so under sustained SPI bus contention
every retry iteration leaks a fresh cas_ctl (~600 bytes per
occurrence).

Fix it by freeing cas_ctl on the spi_async() error path.  While here,
correct the misleading error string: the function calls spi_async(),
not spi_sync().

Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/20260421073259.2259783-1-shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ieee802154: atusb: drop redundant device reference 2026-03-24T00:35:28+00:00 Johan Hovold johan@kernel.org 2026-03-05T10:43:13+00:00 4e9b1994a105fefe558b245f2076a70cc6b498a9 Driver core holds a reference to the USB interface and its parent USB device while the interface is bound to a driver and there is no need to take additional references unless the structures are needed after disconnect. Drop the redundant device reference to reduce cargo culting, make it easier to spot drivers where an extra reference is needed, and reduce the risk of memory leaks when drivers fail to release it. Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Link: https://patch.msgid.link/20260305104313.15898-1-johan@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.

Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.

Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Link: https://patch.msgid.link/20260305104313.15898-1-johan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert more 'alloc_obj' cases to default GFP_KERNEL arguments 2026-02-22T04:03:00+00:00 Linus Torvalds torvalds@linux-foundation.org 2026-02-22T04:03:00+00:00 32a92f8c89326985e05dce8b22d3f0aa07a3e1bd This converts some of the visually simpler cases that have been split over multiple lines. I only did the ones that are easy to verify the resulting diff by having just that final GFP_KERNEL argument on the next line. Somebody should probably do a proper coccinelle script for this, but for me the trivial script actually resulted in an assertion failure in the middle of the script. I probably had made it a bit _too_ trivial. So after fighting that far a while I decided to just do some of the syntactically simpler cases with variations of the previous 'sed' scripts. The more syntactically complex multi-line cases would mostly really want whitespace cleanup anyway. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> 
This converts some of the visually simpler cases that have been split
over multiple lines.  I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.

Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script.  I probably had made it a bit _too_ trivial.

So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.

The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert 'alloc_obj' family to use the new default GFP_KERNEL argument 2026-02-22T01:09:51+00:00 Linus Torvalds torvalds@linux-foundation.org 2026-02-22T00:37:42+00:00 bf4afc53b77aeaa48b5409da5c8da6bb4eff7f43 This was done entirely with mindless brute force, using git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' | xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/' to convert the new alloc_obj() users that had a simple GFP_KERNEL argument to just drop that argument. Note that due to the extreme simplicity of the scripting, any slightly more complex cases spread over multiple lines would not be triggered: they definitely exist, but this covers the vast bulk of the cases, and the resulting diff is also then easier to check automatically. For the same reason the 'flex' versions will be done as a separate conversion. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> 
This was done entirely with mindless brute force, using

    git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
        xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'

to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.

Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.

For the same reason the 'flex' versions will be done as a separate
conversion.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
treewide: Replace kmalloc with kmalloc_obj for non-scalar types 2026-02-21T09:02:28+00:00 Kees Cook kees@kernel.org 2026-02-21T07:49:23+00:00 69050f8d6d075dc01af7a5f2f550a8067510366f This is the result of running the Coccinelle script from scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to avoid scalar types (which need careful case-by-case checking), and instead replace kmalloc-family calls that allocate struct or union object instances: Single allocations: kmalloc(sizeof(TYPE), ...) are replaced with: kmalloc_obj(TYPE, ...) Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...) are replaced with: kmalloc_objs(TYPE, COUNT, ...) Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...) are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...) (where TYPE may also be *VAR) The resulting allocations no longer return "void *", instead returning "TYPE *". Signed-off-by: Kees Cook <kees@kernel.org> 
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:

Single allocations:	kmalloc(sizeof(TYPE), ...)
are replaced with:	kmalloc_obj(TYPE, ...)

Array allocations:	kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with:	kmalloc_objs(TYPE, COUNT, ...)

Flex array allocations:	kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with:	kmalloc_flex(*PTR, FAM, COUNT, ...)

(where TYPE may also be *VAR)

The resulting allocations no longer return "void *", instead returning
"TYPE *".

Signed-off-by: Kees Cook <kees@kernel.org>
Merge tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next 2025-03-27T04:48:21+00:00 Linus Torvalds torvalds@linux-foundation.org 2025-03-27T04:48:21+00:00 1a9239bb4253f9076b5b4b2a1a4e8d7defd77a95 Pull networking updates from Jakub Kicinski: "Core & protocols: - Continue Netlink conversions to per-namespace RTNL lock (IPv4 routing, routing rules, routing next hops, ARP ioctls) - Continue extending the use of netdev instance locks. As a driver opt-in protect queue operations and (in due course) ethtool operations with the instance lock and not RTNL lock. - Support collecting TCP timestamps (data submitted, sent, acked) in BPF, allowing for transparent (to the application) and lower overhead tracking of TCP RPC performance. - Tweak existing networking Rx zero-copy infra to support zero-copy Rx via io_uring. - Optimize MPTCP performance in single subflow mode by 29%. - Enable GRO on packets which went thru XDP CPU redirect (were queued for processing on a different CPU). Improving TCP stream performance up to 2x. - Improve performance of contended connect() by 200% by searching for an available 4-tuple under RCU rather than a spin lock. Bring an additional 229% improvement by tweaking hash distribution. - Avoid unconditionally touching sk_tsflags on RX, improving performance under UDP flood by as much as 10%. - Avoid skb_clone() dance in ping_rcv() to improve performance under ping flood. - Avoid FIB lookup in netfilter if socket is available, 20% perf win. - Rework network device creation (in-kernel) API to more clearly identify network namespaces and their roles. There are up to 4 namespace roles but we used to have just 2 netns pointer arguments, interpreted differently based on context. - Use sysfs_break_active_protection() instead of trylock to avoid deadlocks between unregistering objects and sysfs access. - Add a new sysctl and sockopt for capping max retransmit timeout in TCP. - Support masking port and DSCP in routing rule matches. - Support dumping IPv4 multicast addresses with RTM_GETMULTICAST. - Support specifying at what time packet should be sent on AF_XDP sockets. - Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin users. - Add Netlink YAML spec for WiFi (nl80211) and conntrack. - Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols which only need to be exported when IPv6 support is built as a module. - Age FDB entries based on Rx not Tx traffic in VxLAN, similar to normal bridging. - Allow users to specify source port range for GENEVE tunnels. - netconsole: allow attaching kernel release, CPU ID and task name to messages as metadata Driver API: - Continue rework / fixing of Energy Efficient Ethernet (EEE) across the SW layers. Delegate the responsibilities to phylink where possible. Improve its handling in phylib. - Support symmetric OR-XOR RSS hashing algorithm. - Support tracking and preserving IRQ affinity by NAPI itself. - Support loopback mode speed selection for interface selftests. Device drivers: - Remove the IBM LCS driver for s390 - Remove the sb1000 cable modem driver - Add support for SFP module access over SMBus - Add MCTP transport driver for MCTP-over-USB - Enable XDP metadata support in multiple drivers - Ethernet high-speed NICs: - Broadcom (bnxt): - add PCIe TLP Processing Hints (TPH) support for new AMD platforms - support dumping RoCE queue state for debug - opt into instance locking - Intel (100G, ice, idpf): - ice: rework MSI-X IRQ management and distribution - ice: support for E830 devices - iavf: add support for Rx timestamping - iavf: opt into instance locking - nVidia/Mellanox: - mlx4: use page pool memory allocator for Rx - mlx5: support for one PTP device per hardware clock - mlx5: support for 200Gbps per-lane link modes - mlx5: move IPSec policy check after decryption - AMD/Solarflare: - support FW flashing via devlink - Cisco (enic): - use page pool memory allocator for Rx - enable 32, 64 byte CQEs - get max rx/tx ring size from the device - Meta (fbnic): - support flow steering and RSS configuration - report queue stats - support TCP segmentation - support IRQ coalescing - support ring size configuration - Marvell/Cavium: - support AF_XDP - Wangxun: - support for PTP clock and timestamping - Huawei (hibmcge): - checksum offload - add more statistics - Ethernet virtual: - VirtIO net: - aggressively suppress Tx completions, improve perf by 96% with 1 CPU and 55% with 2 CPUs - expose NAPI to IRQ mapping and persist NAPI settings - Google (gve): - support XDP in DQO RDA Queue Format - opt into instance locking - Microsoft vNIC: - support BIG TCP - Ethernet NICs consumer, and embedded: - Synopsys (stmmac): - cleanup Tx and Tx clock setting and other link-focused cleanups - enable SGMII and 2500BASEX mode switching for Intel platforms - support Sophgo SG2044 - Broadcom switches (b53): - support for BCM53101 - TI: - iep: add perout configuration support - icssg: support XDP - Cadence (macb): - implement BQL - Xilinx (axinet): - support dynamic IRQ moderation and changing coalescing at runtime - implement BQL - report standard stats - MediaTek: - support phylink managed EEE - Intel: - igc: don't restart the interface on every XDP program change - RealTek (r8169): - support reading registers of internal PHYs directly - increase max jumbo packet size on RTL8125/RTL8126 - Airoha: - support for RISC-V NPU packet processing unit - enable scatter-gather and support MTU up to 9kB - Tehuti (tn40xx): - support cards with TN4010 MAC and an Aquantia AQR105 PHY - Ethernet PHYs: - support for TJA1102S, TJA1121 - dp83tg720: add randomized polling intervals for link detection - dp83822: support changing the transmit amplitude voltage - support for LEDs on 88q2xxx - CAN: - canxl: support Remote Request Substitution bit access - flexcan: add S32G2/S32G3 SoC - WiFi: - remove cooked monitor support - strict mode for better AP testing - basic EPCS support - OMI RX bandwidth reduction support - batman-adv: add support for jumbo frames - WiFi drivers: - RealTek (rtw88): - support RTL8814AE and RTL8814AU - RealTek (rtw89): - switch using wiphy_lock and wiphy_work - add BB context to manipulate two PHY as preparation of MLO - improve BT-coexistence mechanism to play A2DP smoothly - Intel (iwlwifi): - add new iwlmld sub-driver for latest HW/FW combinations - MediaTek (mt76): - preparation for mt7996 Multi-Link Operation (MLO) support - Qualcomm/Atheros (ath12k): - continued work on MLO - Silabs (wfx): - Wake-on-WLAN support - Bluetooth: - add support for skb TX SND/COMPLETION timestamping - hci_core: enable buffer flow control for SCO/eSCO - coredump: log devcd dumps into the monitor - Bluetooth drivers: - intel: add support to configure TX power - nxp: handle bootloader error during cmd5 and cmd7" * tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1681 commits) unix: fix up for "apparmor: add fine grained af_unix mediation" mctp: Fix incorrect tx flow invalidation condition in mctp-i2c net: usb: asix: ax88772: Increase phy_name size net: phy: Introduce PHY_ID_SIZE — minimum size for PHY ID string net: libwx: fix Tx L4 checksum net: libwx: fix Tx descriptor content for some tunnel packets atm: Fix NULL pointer dereference net: tn40xx: add pci-id of the aqr105-based Tehuti TN4010 cards net: tn40xx: prepare tn40xx driver to find phy of the TN9510 card net: tn40xx: create swnode for mdio and aqr105 phy and add to mdiobus net: phy: aquantia: add essential functions to aqr105 driver net: phy: aquantia: search for firmware-name in fwnode net: phy: aquantia: add probe function to aqr105 for firmware loading net: phy: Add swnode support to mdiobus_scan gve: add XDP DROP and PASS support for DQ gve: update XDP allocation path support RX buffer posting gve: merge packet buffer size fields gve: update GQ RX to use buf_size gve: introduce config-based allocation for XDP gve: remove xdp_xsk_done and xdp_xsk_wakeup statistics ... 
Pull networking updates from Jakub Kicinski:
 "Core & protocols:

   - Continue Netlink conversions to per-namespace RTNL lock
     (IPv4 routing, routing rules, routing next hops, ARP ioctls)

   - Continue extending the use of netdev instance locks. As a driver
     opt-in protect queue operations and (in due course) ethtool
     operations with the instance lock and not RTNL lock.

   - Support collecting TCP timestamps (data submitted, sent, acked) in
     BPF, allowing for transparent (to the application) and lower
     overhead tracking of TCP RPC performance.

   - Tweak existing networking Rx zero-copy infra to support zero-copy
     Rx via io_uring.

   - Optimize MPTCP performance in single subflow mode by 29%.

   - Enable GRO on packets which went thru XDP CPU redirect (were queued
     for processing on a different CPU). Improving TCP stream
     performance up to 2x.

   - Improve performance of contended connect() by 200% by searching for
     an available 4-tuple under RCU rather than a spin lock. Bring an
     additional 229% improvement by tweaking hash distribution.

   - Avoid unconditionally touching sk_tsflags on RX, improving
     performance under UDP flood by as much as 10%.

   - Avoid skb_clone() dance in ping_rcv() to improve performance under
     ping flood.

   - Avoid FIB lookup in netfilter if socket is available, 20% perf win.

   - Rework network device creation (in-kernel) API to more clearly
     identify network namespaces and their roles. There are up to 4
     namespace roles but we used to have just 2 netns pointer arguments,
     interpreted differently based on context.

   - Use sysfs_break_active_protection() instead of trylock to avoid
     deadlocks between unregistering objects and sysfs access.

   - Add a new sysctl and sockopt for capping max retransmit timeout in
     TCP.

   - Support masking port and DSCP in routing rule matches.

   - Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.

   - Support specifying at what time packet should be sent on AF_XDP
     sockets.

   - Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin
     users.

   - Add Netlink YAML spec for WiFi (nl80211) and conntrack.

   - Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
     which only need to be exported when IPv6 support is built as a
     module.

   - Age FDB entries based on Rx not Tx traffic in VxLAN, similar to
     normal bridging.

   - Allow users to specify source port range for GENEVE tunnels.

   - netconsole: allow attaching kernel release, CPU ID and task name to
     messages as metadata

  Driver API:

   - Continue rework / fixing of Energy Efficient Ethernet (EEE) across
     the SW layers. Delegate the responsibilities to phylink where
     possible. Improve its handling in phylib.

   - Support symmetric OR-XOR RSS hashing algorithm.

   - Support tracking and preserving IRQ affinity by NAPI itself.

   - Support loopback mode speed selection for interface selftests.

  Device drivers:

   - Remove the IBM LCS driver for s390

   - Remove the sb1000 cable modem driver

   - Add support for SFP module access over SMBus

   - Add MCTP transport driver for MCTP-over-USB

   - Enable XDP metadata support in multiple drivers

   - Ethernet high-speed NICs:
      - Broadcom (bnxt):
         - add PCIe TLP Processing Hints (TPH) support for new AMD
           platforms
         - support dumping RoCE queue state for debug
         - opt into instance locking
      - Intel (100G, ice, idpf):
         - ice: rework MSI-X IRQ management and distribution
         - ice: support for E830 devices
         - iavf: add support for Rx timestamping
         - iavf: opt into instance locking
      - nVidia/Mellanox:
         - mlx4: use page pool memory allocator for Rx
         - mlx5: support for one PTP device per hardware clock
         - mlx5: support for 200Gbps per-lane link modes
         - mlx5: move IPSec policy check after decryption
      - AMD/Solarflare:
         - support FW flashing via devlink
      - Cisco (enic):
         - use page pool memory allocator for Rx
         - enable 32, 64 byte CQEs
         - get max rx/tx ring size from the device
      - Meta (fbnic):
         - support flow steering and RSS configuration
         - report queue stats
         - support TCP segmentation
         - support IRQ coalescing
         - support ring size configuration
      - Marvell/Cavium:
         - support AF_XDP
      - Wangxun:
         - support for PTP clock and timestamping
      - Huawei (hibmcge):
         - checksum offload
         - add more statistics

   - Ethernet virtual:
      - VirtIO net:
         - aggressively suppress Tx completions, improve perf by 96%
           with 1 CPU and 55% with 2 CPUs
         - expose NAPI to IRQ mapping and persist NAPI settings
      - Google (gve):
         - support XDP in DQO RDA Queue Format
         - opt into instance locking
      - Microsoft vNIC:
         - support BIG TCP

   - Ethernet NICs consumer, and embedded:
      - Synopsys (stmmac):
         - cleanup Tx and Tx clock setting and other link-focused
           cleanups
         - enable SGMII and 2500BASEX mode switching for Intel platforms
         - support Sophgo SG2044
      - Broadcom switches (b53):
         - support for BCM53101
      - TI:
         - iep: add perout configuration support
         - icssg: support XDP
      - Cadence (macb):
         - implement BQL
      - Xilinx (axinet):
         - support dynamic IRQ moderation and changing coalescing at
           runtime
         - implement BQL
         - report standard stats
      - MediaTek:
         - support phylink managed EEE
      - Intel:
         - igc: don't restart the interface on every XDP program change
      - RealTek (r8169):
         - support reading registers of internal PHYs directly
         - increase max jumbo packet size on RTL8125/RTL8126
      - Airoha:
         - support for RISC-V NPU packet processing unit
         - enable scatter-gather and support MTU up to 9kB
      - Tehuti (tn40xx):
         - support cards with TN4010 MAC and an Aquantia AQR105 PHY

   - Ethernet PHYs:
      - support for TJA1102S, TJA1121
      - dp83tg720: add randomized polling intervals for link detection
      - dp83822: support changing the transmit amplitude voltage
      - support for LEDs on 88q2xxx

   - CAN:
      - canxl: support Remote Request Substitution bit access
      - flexcan: add S32G2/S32G3 SoC

   - WiFi:
      - remove cooked monitor support
      - strict mode for better AP testing
      - basic EPCS support
      - OMI RX bandwidth reduction support
      - batman-adv: add support for jumbo frames

   - WiFi drivers:
      - RealTek (rtw88):
         - support RTL8814AE and RTL8814AU
      - RealTek (rtw89):
         - switch using wiphy_lock and wiphy_work
         - add BB context to manipulate two PHY as preparation of MLO
         - improve BT-coexistence mechanism to play A2DP smoothly
      - Intel (iwlwifi):
         - add new iwlmld sub-driver for latest HW/FW combinations
      - MediaTek (mt76):
         - preparation for mt7996 Multi-Link Operation (MLO) support
      - Qualcomm/Atheros (ath12k):
         - continued work on MLO
      - Silabs (wfx):
         - Wake-on-WLAN support

   - Bluetooth:
      - add support for skb TX SND/COMPLETION timestamping
      - hci_core: enable buffer flow control for SCO/eSCO
      - coredump: log devcd dumps into the monitor

   - Bluetooth drivers:
      - intel: add support to configure TX power
      - nxp: handle bootloader error during cmd5 and cmd7"

* tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1681 commits)
  unix: fix up for "apparmor: add fine grained af_unix mediation"
  mctp: Fix incorrect tx flow invalidation condition in mctp-i2c
  net: usb: asix: ax88772: Increase phy_name size
  net: phy: Introduce PHY_ID_SIZE — minimum size for PHY ID string
  net: libwx: fix Tx L4 checksum
  net: libwx: fix Tx descriptor content for some tunnel packets
  atm: Fix NULL pointer dereference
  net: tn40xx: add pci-id of the aqr105-based Tehuti TN4010 cards
  net: tn40xx: prepare tn40xx driver to find phy of the TN9510 card
  net: tn40xx: create swnode for mdio and aqr105 phy and add to mdiobus
  net: phy: aquantia: add essential functions to aqr105 driver
  net: phy: aquantia: search for firmware-name in fwnode
  net: phy: aquantia: add probe function to aqr105 for firmware loading
  net: phy: Add swnode support to mdiobus_scan
  gve: add XDP DROP and PASS support for DQ
  gve: update XDP allocation path support RX buffer posting
  gve: merge packet buffer size fields
  gve: update GQ RX to use buf_size
  gve: introduce config-based allocation for XDP
  gve: remove xdp_xsk_done and xdp_xsk_wakeup statistics
  ...
ieee802154: ca8210: Switch to using gpiod API 2025-03-06T20:55:18+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2025-03-05T10:55:36+00:00 20629a48d50ad98cb9376dedeec1e98aff092ad9 This updates the driver to gpiod API, and removes yet another use of of_get_named_gpio(). With this, invert the logic of the reset pin which is active-low and add a quirk for the legacy and incorrect device tree descriptions. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/20250305105656.2133487-4-andriy.shevchenko@linux.intel.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> 
This updates the driver to gpiod API, and removes yet another use of
of_get_named_gpio().

With this, invert the logic of the reset pin which is active-low
and add a quirk for the legacy and incorrect device tree descriptions.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/20250305105656.2133487-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
ieee802154: ca8210: Get platform data via dev_get_platdata() 2025-03-06T20:55:18+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2025-03-05T10:55:35+00:00 0a3e89b06d36d55392829681f63ce0c74861901b Access to platform data via dev_get_platdata() getter to make code cleaner. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/20250305105656.2133487-3-andriy.shevchenko@linux.intel.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> 
Access to platform data via dev_get_platdata() getter to make code cleaner.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/20250305105656.2133487-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
ieee802154: ca8210: Use proper setters and getters for bitwise types 2025-03-06T20:55:17+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2025-03-05T10:55:34+00:00 169b2262205836a5d1213ff44dca2962276bece1 Sparse complains that the driver doesn't respect the bitwise types: drivers/net/ieee802154/ca8210.c:1796:27: warning: incorrect type in assignment (different base types) drivers/net/ieee802154/ca8210.c:1796:27: expected restricted __le16 [addressable] [assigned] [usertype] pan_id drivers/net/ieee802154/ca8210.c:1796:27: got unsigned short [usertype] drivers/net/ieee802154/ca8210.c:1801:25: warning: incorrect type in assignment (different base types) drivers/net/ieee802154/ca8210.c:1801:25: expected restricted __le16 [addressable] [assigned] [usertype] pan_id drivers/net/ieee802154/ca8210.c:1801:25: got unsigned short [usertype] drivers/net/ieee802154/ca8210.c:1928:28: warning: incorrect type in argument 3 (different base types) drivers/net/ieee802154/ca8210.c:1928:28: expected unsigned short [usertype] dst_pan_id drivers/net/ieee802154/ca8210.c:1928:28: got restricted __le16 [addressable] [usertype] pan_id Use proper setters and getters for bitwise types. Note, in accordance with [1] the protocol is little endian. Link: https://www.cascoda.com/wp-content/uploads/2018/11/CA-8210_datasheet_0418.pdf [1] Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/20250305105656.2133487-2-andriy.shevchenko@linux.intel.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> 
Sparse complains that the driver doesn't respect the bitwise types:

drivers/net/ieee802154/ca8210.c:1796:27: warning: incorrect type in assignment (different base types)
drivers/net/ieee802154/ca8210.c:1796:27:    expected restricted __le16 [addressable] [assigned] [usertype] pan_id
drivers/net/ieee802154/ca8210.c:1796:27:    got unsigned short [usertype]
drivers/net/ieee802154/ca8210.c:1801:25: warning: incorrect type in assignment (different base types)
drivers/net/ieee802154/ca8210.c:1801:25:    expected restricted __le16 [addressable] [assigned] [usertype] pan_id
drivers/net/ieee802154/ca8210.c:1801:25:    got unsigned short [usertype]
drivers/net/ieee802154/ca8210.c:1928:28: warning: incorrect type in argument 3 (different base types)
drivers/net/ieee802154/ca8210.c:1928:28:    expected unsigned short [usertype] dst_pan_id
drivers/net/ieee802154/ca8210.c:1928:28:    got restricted __le16 [addressable] [usertype] pan_id

Use proper setters and getters for bitwise types.

Note, in accordance with [1] the protocol is little endian.

Link: https://www.cascoda.com/wp-content/uploads/2018/11/CA-8210_datasheet_0418.pdf [1]
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/20250305105656.2133487-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>