linux-stable.git/drivers/net/ethernet, branch v4.9.239

net: stmmac: removed enabling eee in EEE set callback

2020-10-14T07:48:16+00:00

[ Upstream commit 7241c5a697479c7d0c5a96595822cdab750d41ae ]

EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.

Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.

Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.

Fixes: 8a7493e58ad6 ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng 
Acked-by: Mark Gross 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

Revert "ravb: Fixed to be able to unload modules"

2020-10-14T07:48:14+00:00

commit 77972b55fb9d35d4a6b0abca99abffaa4ec6a85b upstream.

This reverts commit 1838d6c62f57836639bd3d83e7855e0ee4f6defc.

This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call.  This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.

During boot, the Micrel PHY is detected like this:

    Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
    ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.

  A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
     merely adds the device, but does not probe it yet, as
     really_probe() returns early due to defer_all_probes being set:

       dpm_resume+0x128/0x4f8
	 device_resume+0xcc/0x1b0
	   dpm_run_callback+0x74/0x340
	     ravb_resume+0x190/0x1b8
	       ravb_open+0x84/0x770
		 of_mdiobus_register+0x1e0/0x468
		   of_mdiobus_register_phy+0x1b8/0x250
		     of_mdiobus_phy_device_register+0x178/0x1e8
		       phy_device_register+0x114/0x1b8
			 device_add+0x3d4/0x798
			   bus_probe_device+0x98/0xa0
			     device_initial_probe+0x10/0x18
			       __device_attach+0xe4/0x140
				 bus_for_each_drv+0x64/0xc8
				   __device_attach_driver+0xb8/0xe0
				     driver_probe_device.part.11+0xc4/0xd8
				       really_probe+0x32c/0x3b8

     Later, phy_attach_direct() notices no PHY driver has been bound,
     and falls back to the Generic PHY, leading to degraded operation:

       Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
       ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

  B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
     to UMH_DISABLED, and MDIO initialization fails completely:

       mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
       ravb e6800000.ethernet eth0: failed to initialize MDIO
       PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
       PM: Device e6800000.ethernet failed to resume: error -16

     Ignoring -EBUSY in phy_request_driver_module(), like was done for
     -ENOENT in commit 21e194425abd65b5 ("net: phy: fix issue with loading
     PHY driver w/o initramfs"), would makes it fall back to the Generic
     PHY, like in the CONFIG_MODULES=n case.

Signed-off-by: Geert Uytterhoeven 
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: dec: de2104x: Increase receive ring size for Tulip

2020-10-14T07:48:12+00:00

[ Upstream commit ee460417d254d941dfea5fb7cff841f589643992 ]

Increase Rx ring size to address issue where hardware is reaching
the receive work limit.

Before:

[  102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached
[  102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached
[  102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached
[  102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached

Signed-off-by: Lucy Yan 
Reviewed-by: Moritz Fischer 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

e1000: Do not perform reset in reset_task if we are already down

2020-10-01T18:40:14+00:00

[ Upstream commit 49ee3c2ab5234757bfb56a0b3a3cb422f427e3a3 ]

We are seeing a deadlock in e1000 down when NAPI is being disabled. Looking
over the kernel function trace of the system it appears that the interface
is being closed and then a reset is hitting which deadlocks the interface
as the NAPI interface is already disabled.

To prevent this from happening I am disabling the reset task when
__E1000_DOWN is already set. In addition code has been added so that we set
the __E1000_DOWN while holding the __E1000_RESET flag in e1000_close in
order to guarantee that the reset task will not run after we have started
the close call.

Signed-off-by: Alexander Duyck 
Tested-by: Maxim Zhukov 
Signed-off-by: Jeff Kirsher 
Signed-off-by: Sasha Levin

bnxt_en: Protect bnxt_set_eee() and bnxt_set_pauseparam() with mutex.

2020-10-01T18:40:00+00:00

[ Upstream commit a53906908148d64423398a62c4435efb0d09652c ]

All changes related to bp->link_info require the protection of the
link_lock mutex.  It's not sufficient to rely just on RTNL.

Fixes: 163e9ef63641 ("bnxt_en: Fix race when modifying pause settings.")
Reviewed-by: Edwin Peer 
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

bnxt: don't enable NAPI until rings are ready

2020-09-12T09:47:39+00:00

commit 96ecdcc992eb7f468b2cf829b0f5408a1fad4668 upstream.

Netpoll can try to poll napi as soon as napi_enable() is called.
It crashes trying to access a doorbell which is still NULL:

 BUG: kernel NULL pointer dereference, address: 0000000000000000
 CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S                5.9.0-rc1-00469-g5fd99b5d9950-dirty #26
 RIP: 0010:bnxt_poll+0x121/0x1c0
 Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02
41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a
  netpoll_poll_dev+0xbd/0x1a0
  __netpoll_send_skb+0x1b2/0x210
  netpoll_send_udp+0x2c9/0x406
  write_ext_msg+0x1d7/0x1f0
  console_unlock+0x23c/0x520
  vprintk_emit+0xe0/0x1d0
  printk+0x58/0x6f
  x86_vector_activate.cold+0xf/0x46
  __irq_domain_activate_irq+0x50/0x80
  __irq_domain_activate_irq+0x32/0x80
  __irq_domain_activate_irq+0x32/0x80
  irq_domain_activate_irq+0x25/0x40
  __setup_irq+0x2d2/0x700
  request_threaded_irq+0xfb/0x160
  __bnxt_open_nic+0x3b1/0x750
  bnxt_open_nic+0x19/0x30
  ethtool_set_channels+0x1ac/0x220
  dev_ethtool+0x11ba/0x2240
  dev_ioctl+0x1cf/0x390
  sock_do_ioctl+0x95/0x130

Reported-by: Rob Sherwood 
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Jakub Kicinski 
Reviewed-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()

2020-09-12T09:47:39+00:00

commit cbedcb044e9cc4e14bbe6658111224bb923094f4 upstream.

On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.

  mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
  mlx4_core: probe of 0000:b1:00.0 failed with error -12

Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.

Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Shung-Hsi Yu 
Signed-off-by: David S. Miller 
Signed-off-by: Greg Kroah-Hartman

tg3: Fix soft lockup when tg3_reset_task() fails.

2020-09-12T09:47:34+00:00

[ Upstream commit 556699341efa98243e08e34401b3f601da91f5a3 ]

If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled.  A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.

Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails.  tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails.  We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task().  Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.

Reported-by: David Christensen 
Reported-by: Baptiste Covolato 
Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bnxt_en: Fix PCI AER error recovery flow

2020-09-12T09:47:34+00:00

[ Upstream commit df3875ec550396974b1d8a518bd120d034738236 ]

When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.

Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam 
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bnxt_en: Check for zero dir entries in NVRAM.

2020-09-12T09:47:34+00:00

[ Upstream commit dbbfa96ad920c50d58bcaefa57f5f33ceef9d00e ]

If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam 
Signed-off-by: Michael Chan 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin