linux-stable.git/drivers/net/ethernet/mscc, branch linux-6.2.y

net: mscc: ocelot: fix stats region batching

2023-03-30T10:51:20+00:00

[ Upstream commit 6acc72a43eac78a309160d0a7512bbc59bcdd757 ]

The blamed commit changed struct ocelot_stat_layout :: "u32 offset" to
"u32 reg".

However, "u32 reg" is not quite a register address, but an enum
ocelot_reg, which in itself encodes an enum ocelot_target target in the
upper bits, and an index into the ocelot->map[target][] array in the
lower bits.

So, whereas the previous code comparison between stats_layout[i].offset
and last + 1 was correct (because those "offsets" at the time were
32-bit relative addresses), the new code, comparing layout[i].reg to
last + 4 is not correct, because the "reg" here is an enum/index, not an
actual register address.

What we want to compare are indeed register addresses, but to do that,
we need to actually go through the same motions as
__ocelot_bulk_read_ix() itself.

With this bug, all statistics counters are deemed by
ocelot_prepare_stats_regions() as constituting their own region.
(Truncated) log on VSC9959 (Felix) below (prints added by me):

Before:

region of 1 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x001]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x002]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x041]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x042]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x081]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x0ac]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x100]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x101]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x111]

After:

region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 45 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]

Since commit d87b1c08f38a ("net: mscc: ocelot: use bulk reads for
stats") intended bulking as a performance improvement, and since now,
with trivial-sized regions, performance is even worse than without
bulking at all, this could easily qualify as a performance regression.

Fixes: d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset")
Signed-off-by: Vladimir Oltean 
Acked-by: Colin Foster 
Tested-by: Colin Foster 
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: mscc: ocelot: fix all IPv6 getting trapped to CPU when PTP timestamping is used

2023-02-09T09:52:44+00:00

While running this selftest which usually passes:

~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc            [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti           [ OK ]
TEST: swp0: Multicast IPv4 to joined group                          [ OK ]
TEST: swp0: Multicast IPv4 to unknown group                         [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc                [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti               [ OK ]
TEST: swp0: Multicast IPv6 to joined group                          [ OK ]
TEST: swp0: Multicast IPv6 to unknown group                         [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc                [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti               [ OK ]

if I start PTP timestamping then run it again (debug prints added by me),
the unknown IPv6 MC traffic is seen by the CPU port even when it should
have been dropped:

~/selftests/drivers/net/dsa# ptp4l -i swp0 -2 -P -m
ptp4l[225.410]: selected /dev/ptp1 as PTP clock
[  225.445746] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_add: port 0 adding L2 PTP trap
[  225.453815] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP event trap
[  225.462703] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP general trap
[  225.471768] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP event trap
[  225.480651] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP general trap
ptp4l[225.488]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[225.488]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
^C
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc            [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti           [ OK ]
TEST: swp0: Multicast IPv4 to joined group                          [ OK ]
TEST: swp0: Multicast IPv4 to unknown group                         [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc                [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti               [ OK ]
TEST: swp0: Multicast IPv6 to joined group                          [ OK ]
TEST: swp0: Multicast IPv6 to unknown group                         [FAIL]
        reception succeeded, but should have failed
TEST: swp0: Multicast IPv6 to unknown group, promisc                [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti               [ OK ]

The PGID_MCIPV6 is configured correctly to not flood to the CPU,
I checked that.

Furthermore, when I disable back PTP RX timestamping (ptp4l doesn't do
that when it exists), packets are RX filtered again as they should be:

~/selftests/drivers/net/dsa# hwstamp_ctl -i swp0 -r 0
[  218.202854] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_del: port 0 removing L2 PTP trap
[  218.212656] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP event trap
[  218.222975] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP general trap
[  218.233133] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP event trap
[  218.242251] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP general trap
current settings:
tx_type 1
rx_filter 12
new settings:
tx_type 1
rx_filter 0
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address                     [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc            [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti           [ OK ]
TEST: swp0: Multicast IPv4 to joined group                          [ OK ]
TEST: swp0: Multicast IPv4 to unknown group                         [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc                [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti               [ OK ]
TEST: swp0: Multicast IPv6 to joined group                          [ OK ]
TEST: swp0: Multicast IPv6 to unknown group                         [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc                [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti               [ OK ]

So it's clear that something in the PTP RX trapping logic went wrong.

Looking a bit at the code, I can see that there are 4 typos, which
populate "ipv4" VCAP IS2 key filter fields for IPv6 keys.

VCAP IS2 keys of type OCELOT_VCAP_KEY_IPV4 and OCELOT_VCAP_KEY_IPV6 are
handled by is2_entry_set(). OCELOT_VCAP_KEY_IPV4 looks at
&filter->key.ipv4, and OCELOT_VCAP_KEY_IPV6 at &filter->key.ipv6.
Simply put, when we populate the wrong key field, &filter->key.ipv6
fields "proto.mask" and "proto.value" remain all zeroes (or "don't care").
So is2_entry_set() will enter the "else" of this "if" condition:

	if (msk == 0xff && (val == IPPROTO_TCP || val == IPPROTO_UDP))

and proceed to ignore the "proto" field. The resulting rule will match
on all IPv6 traffic, trapping it to the CPU.

This is the reason why the local_termination.sh selftest sees it,
because control traps are stronger than the PGID_MCIPV6 used for
flooding (from the forwarding data path).

But the problem is in fact much deeper. We trap all IPv6 traffic to the
CPU, but if we're bridged, we set skb->offload_fwd_mark = 1, so software
forwarding will not take place and IPv6 traffic will never reach its
destination.

The fix is simple - correct the typos.

I was intentionally inaccurate in the commit message about the breakage
occurring when any PTP timestamping is enabled. In fact it only happens
when L4 timestamping is requested (HWTSTAMP_FILTER_PTP_V2_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT). But ptp4l requests a larger RX
timestamping filter than it needs for "-2": HWTSTAMP_FILTER_PTP_V2_EVENT.
I wanted people skimming through git logs to not think that the bug
doesn't affect them because they only use ptp4l in L2 mode.

Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean 
Reviewed-by: Simon Horman 
Link: https://lore.kernel.org/r/20230207183117.1745754-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni

net: mscc: ocelot: fix VCAP filters not matching on MAC with "protocol 802.1Q"

2023-02-07T11:20:21+00:00

Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.

With a command such as the following:

tc filter add dev $swp1 ingress chain $(IS1 2) pref 3 \
	protocol 802.1Q flower skip_sw vlan_id 200 src_mac $h1_mac \
	action vlan modify id 300 \
	action goto chain $(IS2 0 0)

the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.

The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.

The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.

The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e6107e ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.

The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.

To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".

Fixes: 86b956de119c ("net: mscc: ocelot: support matching on EtherType")
Signed-off-by: Vladimir Oltean 
Reviewed-by: Simon Horman 
Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni

net: mscc: ocelot: issue a warning if stats are incorrectly ordered

2022-11-22T14:36:44+00:00

Ocelot uses regmap_bulk_read() operations to efficiently read stats
registers. Currently the implementation relies on the stats layout to be
ordered to be most efficient.

Issue a warning if any future implementations happen to break this pattern.

Signed-off-by: Colin Foster 
Co-developed-by: Vladimir Oltean 
Reviewed-by: Vladimir Oltean 
Signed-off-by: Paolo Abeni

net: mscc: ocelot: remove unnecessary exposure of stats structures

2022-11-22T14:36:43+00:00

Since commit 4d1d157fb6a4 ("net: mscc: ocelot: share the common stat
definitions between all drivers") there is no longer a need to share the
stats structures to the world. Relocate these definitions to inside
ocelot_stats.c instead of a global include header.

Signed-off-by: Colin Foster 
Reviewed-by: Vladimir Oltean 
Signed-off-by: Paolo Abeni

net: mscc: ocelot: remove redundant stats_layout pointers

2022-11-22T14:36:43+00:00

Ever since commit 4d1d157fb6a4 ("net: mscc: ocelot: share the common stat
definitions between all drivers") the stats_layout entry in ocelot and
felix drivers have become redundant. Remove the unnecessary code.

Suggested-by: Vladimir Oltean 
Signed-off-by: Colin Foster 
Reviewed-by: Vladimir Oltean 
Signed-off-by: Paolo Abeni

net: mscc: ocelot: drop workaround for forcing RX flow control

2022-11-16T04:34:27+00:00

As phylink gained generic support for PHYs with rate matching via PAUSE
frames, the phylink_mac_link_up() method will be called with the maximum
speed and with rx_pause=true if rate matching is in use. This means that
setups with 2500base-x as the SERDES protocol between the MAC/PCS and
the PHY now work with no need for the driver to do anything special.

Tested with fsl-ls1028a-qds-7777.dts.

Signed-off-by: Vladimir Oltean 
Reviewed-by: Russell King (Oracle) 
Signed-off-by: Jakub Kicinski

net: remove explicit phylink_generic_validate() references

2022-11-08T01:54:57+00:00

Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.

Any remaining instances that have not been addressed by this patch can
be fixed up later.

Signed-off-by: Russell King (Oracle) 
Reviewed-by: Vladimir Oltean 
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski

net: remove unused ndo_get_devlink_port

2022-11-04T03:48:36+00:00

Remove ndo_get_devlink_port which is no longer used alongside with the
implementations in drivers.

Signed-off-by: Jiri Pirko 
Signed-off-by: Jakub Kicinski

net: make drivers to use SET_NETDEV_DEVLINK_PORT to set devlink_port

2022-11-04T03:48:34+00:00

Benefit from the previously implemented tracking of netdev events in
devlink code and instead of calling  devlink_port_type_eth_set() and
devlink_port_type_clear() to set devlink port type and link to related
netdev, use SET_NETDEV_DEVLINK_PORT() macro to assign devlink_port
pointer to netdevice which is about to be registered.

Signed-off-by: Jiri Pirko 
Signed-off-by: Jakub Kicinski