It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: db8bcaad5393 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the action of an xdp program was XDP_TX, lan966x was creating a xdp_frame and use this one to send the frame back. But it is also possible to send back the frame without needing a xdp_frame, because it is possible to send it back using the page. And then once the frame is transmitted is possible to use directly page_pool_recycle_direct as lan966x is using page pools. This would save some CPU usage on this path, which results in higher number of transmitted frames. Bellow are the statistics: Frame size: Improvement: 64 ~8% 256 ~11% 512 ~8% 1000 ~0% 1500 ~0% Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Link: https://lore.kernel.org/r/20230422142344.3630602-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From time to time, it was observed that the nanosecond part of the
received timestamp, which is extracted from the IFH, it was actually
bigger than 1 second. So then when actually calculating the full
received timestamp, based on the nanosecond part from IFH and the second
part which is read from HW, it was actually wrong.
The issue seems to be inside the function lan966x_ifh_get, which
extracts information from an IFH(which is an byte array) and returns the
value in a u64. When extracting the timestamp value from the IFH, which
starts at bit 192 and have the size of 32 bits, then if the most
significant bit was set in the timestamp, then this bit was extended
then the return value became 0xffffffff... . And the reason of this is
because constants without any postfix are treated as signed longs and
that is the reason why '1 << 31' becomes 0xffffffff80000000.
This is fixed by adding the postfix 'ULL' to 1.
Fixes: fd7627833ddf ("net: lan966x: Stop using packing library")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_disconnect() calls phy_detach() which already clears 'phydev' if it is attached to a struct net_device. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230321131745.27688-1-wsa+renesas@sang-engineering.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a frame is injected from CPU, it is required to create an IFH(Inter frame header) which sits in front of the frame that is transmitted. This IFH, contains different fields like destination port, to bypass the analyzer, priotity, etc. Lan966x it is using packing library to set and get the fields of this IFH. But this seems to be an expensive operations. If this is changed with a simpler implementation, the RX will be improved with ~5Mbit while on the TX is a much bigger improvement as it is required to set more fields. Below are the numbers for TX. Before: [ 5] 0.00-10.02 sec 439 MBytes 367 Mbits/sec 0 sender After: [ 5] 0.00-10.00 sec 578 MBytes 485 Mbits/sec 0 sender Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a frame was received to the CPU, the HW is timestamping the frame. In the IFH(Inter Frame Header) it is found the nanosecond part of the timestamps the SW is required to read from HW the second part. But reading the second part it seems to be a expensive operations, so so change this such to read the second part only when rx filter is enabled. Doing this change gives the RX a performance boost of ~70mbit. before: [ 5] 0.00-10.01 sec 546 MBytes 457 Mbits/sec 0 sender now: [ 5] 0.00-10.01 sec 652 MBytes 530 Mbits/sec 0 sender Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
As the function always returns 0 change the return type to be void instead of int. In this way also remove a wrong message in case of error which would never happen. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230312195155.1492881-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IS1 VCAP has it's own list of supported ethernet protocol types which is different than the IS2 VCAP. Therefore separate the list of known protocol types based on the VCAP type. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow rules to be chained between IS1 VCAP and IS2 VCAP. Chaining between IS1 lookups or between IS2 lookups are not supported by the hardware. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable TC command to use IS1 VCAP Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>