commit 600761245952d7f70280add6ce02894f1528992b upstream.
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: db8bcaad5393 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix deletion of existing DSCP mappings in the APP table.
Adding and deleting DSCP entries are replicated per-port, since the
mapping table is global for all ports in the chip. Whenever a mapping
for a DSCP value already exists, the old mapping is deleted first.
However, it is only deleted for the specified port. Fix this by calling
sparx5_dcb_ieee_delapp() instead of dcb_ieee_delapp() as it ought to be.
Reproduce:
// Map and remap DSCP value 63
$ dcb app add dev eth0 dscp-prio 63:1
$ dcb app add dev eth0 dscp-prio 63:2
$ dcb app show dev eth0 dscp-prio
dscp-prio 63:2
$ dcb app show dev eth1 dscp-prio
dscp-prio 63:1 63:2 <-- 63:1 should not be there
Fixes: 8dcf69a64118 ("net: microchip: sparx5: add support for offloading dscp table")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the police was removed from the port, then it was trying to
remove the police from the police id and not from the actual
police index.
The police id represents the id of the police and police index
represents the position in HW where the police is situated.
The port police id can be any number while the port police index
is a number based on the port chip port.
Fix this by deleting the police from HW that is situated at the
police index and not police id.
Fixes: 5390334b59a3 ("net: lan966x: Add port police support using tc-matchall")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull phy updates from Vinod Koul:
"This features a bunch of new device support, a couple of new drivers,
yaml conversion and updates of a few drivers.
Core support:
- New devm_of_phy_optional_get() API with users and conversion
New hardware support:
- Mediatek MT7986 phy support
- Qualcomm SM8550 UFS, PCIe, combo phy support, SM6115 / SM4250 USB3
phy support, SM6350 combo phy support, SM6125 UFS PHY support amd
SM8350 & SM8450 combo phy support
- Qualcomm SNPS eUSB2 eUSB2 repeater drivers
- Allwinner F1C100s USB PHY support
- Tegra xusb support for Tegra234
Updates:
- Yaml conversion for Qualcomm pcie2 phy and usb-hsic-phy
- G4 mode support in Qualcomm UFS phy and support for various SoCs
- Yaml conversion for Meson usb2 phy
- TI Type C support for usb phy for j721
- Yaml conversion for Tegra xusb binding"
* tag 'phy-for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (106 commits)
phy: qcom: phy-qcom-snps-eusb2: Add support for eUSB2 repeater
phy: qcom: Add QCOM SNPS eUSB2 repeater driver
dt-bindings: phy: qcom,snps-eusb2-phy: Add phys property for the repeater
dt-bindings: phy: Add qcom,snps-eusb2-repeater schema file
dt-bindings: phy: amlogic,g12a-usb3-pcie-phy: add missing optional phy-supply property
phy: rockchip-typec: Fix unsigned comparison with less than zero
phy: rockchip-typec: fix tcphy_get_mode error case
phy: qcom: snps-eusb2: Add missing headers
phy: qcom-qmp-combo: Add support for SM8550
phy: qcom-qmp: Add v6 DP register offsets
phy: qcom-qmp: pcs-usb: Add v6 register offsets
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Document SM8550 compatible
phy: qcom: Add QCOM SNPS eUSB2 driver
dt-bindings: phy: Add qcom,snps-eusb2-phy schema file
phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs
phy: qcom-qmp: qserdes-lane-shared: Add v6 register offsets
phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets
phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets
phy: qcom-qmp: pcs-pcie: Add v6 register offsets
phy: qcom-qmp: pcs: Add v6.20 register offsets
...
Per-next-PR merge.
net/smc/af_smc.c
b5dd4d698171 ("net/smc: llc_conf_mutex refactor, replace it with rw_semaphore")
e40b801b3603 ("net/smc: fix potential panic dues to unprotected smc_llc_srv_add_link()")
https://lore.kernel.org/all/20230221124008.6303c330@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When doing timestamping in lan966x and having PROVE_LOCKING
enabled the following warning is shown.
========================================================
WARNING: possible irq lock inversion dependency detected
6.2.0-rc7-01749-gc54e1f7f7e36 #2786 Tainted: G N
--------------------------------------------------------
swapper/0/0 just changed the state of lock:
c2609f50 (_xmit_ETHER#2){+.-.}-{2:2}, at: sch_direct_xmit+0x16c/0x2e8
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&lan966x->ptp_ts_id_lock){+.+.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lan966x->ptp_ts_id_lock);
local_irq_disable();
lock(_xmit_ETHER#2);
lock(&lan966x->ptp_ts_id_lock);
<Interrupt>
lock(_xmit_ETHER#2);
*** DEADLOCK ***
5 locks held by swapper/0/0:
#0: c1001e18 ((&ndev->rs_timer)){+.-.}-{0:0}, at: call_timer_fn+0x0/0x33c
#1: c105e7c4 (rcu_read_lock){....}-{1:2}, at: ndisc_send_skb+0x134/0x81c
#2: c105e7d8 (rcu_read_lock_bh){....}-{1:2}, at: ip6_finish_output2+0x17c/0xc64
#3: c105e7d8 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x4c/0x1224
#4: c3056174 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: __dev_queue_xmit+0x354/0x1224
the shortest dependencies between 2nd lock and 1st lock:
-> (&lan966x->ptp_ts_id_lock){+.+.}-{2:2} {
HARDIRQ-ON-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
lan966x_ptp_irq_handler+0x164/0x2a8
irq_thread_fn+0x1c/0x78
irq_thread+0x130/0x278
kthread+0xec/0x110
ret_from_fork+0x14/0x28
SOFTIRQ-ON-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
lan966x_ptp_irq_handler+0x164/0x2a8
irq_thread_fn+0x1c/0x78
irq_thread+0x130/0x278
kthread+0xec/0x110
ret_from_fork+0x14/0x28
INITIAL USE at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock_irqsave+0x4c/0x68
lan966x_ptp_txtstamp_request+0x128/0x1cc
lan966x_port_xmit+0x224/0x43c
dev_hard_start_xmit+0xa8/0x2f0
sch_direct_xmit+0x108/0x2e8
__dev_queue_xmit+0x41c/0x1224
packet_sendmsg+0xdb4/0x134c
__sys_sendto+0xd0/0x154
sys_send+0x18/0x20
ret_fast_syscall+0x0/0x1c
}
... key at: [<c174ba0c>] __key.2+0x0/0x8
... acquired at:
_raw_spin_lock_irqsave+0x4c/0x68
lan966x_ptp_txtstamp_request+0x128/0x1cc
lan966x_port_xmit+0x224/0x43c
dev_hard_start_xmit+0xa8/0x2f0
sch_direct_xmit+0x108/0x2e8
__dev_queue_xmit+0x41c/0x1224
packet_sendmsg+0xdb4/0x134c
__sys_sendto+0xd0/0x154
sys_send+0x18/0x20
ret_fast_syscall+0x0/0x1c
-> (_xmit_ETHER#2){+.-.}-{2:2} {
HARDIRQ-ON-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
netif_freeze_queues+0x38/0x68
dev_deactivate_many+0xac/0x388
dev_deactivate+0x38/0x6c
linkwatch_do_dev+0x70/0x8c
__linkwatch_run_queue+0xd4/0x1e8
linkwatch_event+0x24/0x34
process_one_work+0x284/0x744
worker_thread+0x28/0x4bc
kthread+0xec/0x110
ret_from_fork+0x14/0x28
IN-SOFTIRQ-W at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
sch_direct_xmit+0x16c/0x2e8
__dev_queue_xmit+0x41c/0x1224
ip6_finish_output2+0x5f4/0xc64
ndisc_send_skb+0x4cc/0x81c
addrconf_rs_timer+0xb0/0x2f8
call_timer_fn+0xb4/0x33c
expire_timers+0xb4/0x10c
run_timer_softirq+0xf8/0x2a8
__do_softirq+0xd4/0x5fc
__irq_exit_rcu+0x138/0x17c
irq_exit+0x8/0x28
__irq_svc+0x90/0xbc
arch_cpu_idle+0x30/0x3c
default_idle_call+0x44/0xac
do_idle+0xc8/0x138
cpu_startup_entry+0x18/0x1c
rest_init+0xcc/0x168
arch_post_acpi_subsys_init+0x0/0x8
INITIAL USE at:
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
netif_freeze_queues+0x38/0x68
dev_deactivate_many+0xac/0x388
dev_deactivate+0x38/0x6c
linkwatch_do_dev+0x70/0x8c
__linkwatch_run_queue+0xd4/0x1e8
linkwatch_event+0x24/0x34
process_one_work+0x284/0x744
worker_thread+0x28/0x4bc
kthread+0xec/0x110
ret_from_fork+0x14/0x28
}
... key at: [<c175974c>] netdev_xmit_lock_key+0x8/0x1c8
... acquired at:
__lock_acquire+0x978/0x2978
lock_acquire.part.0+0xb0/0x248
_raw_spin_lock+0x38/0x48
sch_direct_xmit+0x16c/0x2e8
__dev_queue_xmit+0x41c/0x1224
ip6_finish_output2+0x5f4/0xc64
ndisc_send_skb+0x4cc/0x81c
addrconf_rs_timer+0xb0/0x2f8
call_timer_fn+0xb4/0x33c
expire_timers+0xb4/0x10c
run_timer_softirq+0xf8/0x2a8
__do_softirq+0xd4/0x5fc
__irq_exit_rcu+0x138/0x17c
irq_exit+0x8/0x28
__irq_svc+0x90/0xbc
arch_cpu_idle+0x30/0x3c
default_idle_call+0x44/0xac
do_idle+0xc8/0x138
cpu_startup_entry+0x18/0x1c
rest_init+0xcc/0x168
arch_post_acpi_subsys_init+0x0/0x8
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G N 6.2.0-rc7-01749-gc54e1f7f7e36 #2786
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from mark_lock.part.0+0x59c/0x93c
mark_lock.part.0 from __lock_acquire+0x978/0x2978
__lock_acquire from lock_acquire.part.0+0xb0/0x248
lock_acquire.part.0 from _raw_spin_lock+0x38/0x48
_raw_spin_lock from sch_direct_xmit+0x16c/0x2e8
sch_direct_xmit from __dev_queue_xmit+0x41c/0x1224
__dev_queue_xmit from ip6_finish_output2+0x5f4/0xc64
ip6_finish_output2 from ndisc_send_skb+0x4cc/0x81c
ndisc_send_skb from addrconf_rs_timer+0xb0/0x2f8
addrconf_rs_timer from call_timer_fn+0xb4/0x33c
call_timer_fn from expire_timers+0xb4/0x10c
expire_timers from run_timer_softirq+0xf8/0x2a8
run_timer_softirq from __do_softirq+0xd4/0x5fc
__do_softirq from __irq_exit_rcu+0x138/0x17c
__irq_exit_rcu from irq_exit+0x8/0x28
irq_exit from __irq_svc+0x90/0xbc
Exception stack(0xc1001f20 to 0xc1001f68)
1f20: ffffffff ffffffff 00000001 c011f840 c100e000 c100e000 c1009314 c1009370
1f40: c10f0c1a c0d5e564 c0f5da8c 00000000 00000000 c1001f70 c010f0bc c010f0c0
1f60: 600f0013 ffffffff
__irq_svc from arch_cpu_idle+0x30/0x3c
arch_cpu_idle from default_idle_call+0x44/0xac
default_idle_call from do_idle+0xc8/0x138
do_idle from cpu_startup_entry+0x18/0x1c
cpu_startup_entry from rest_init+0xcc/0x168
rest_init from arch_post_acpi_subsys_init+0x0/0x8
Fix this by using spin_lock_irqsave/spin_lock_irqrestore also
inside lan966x_ptp_irq_handler.
Fixes: e85a96e48e33 ("net: lan966x: Add support for ptp interrupts")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230217210917.2649365-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 81e164c4aec5 ("net: microchip: sparx5: Add automatic
selection of VCAP rule actionset") the VCAP API has the capability to
select automatically the actionset based on the actions that are attached
to the rule. So it is not needed anymore to hardcode the actionset in the
driver, therefore it is OK to remove this.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vcap_admin structures in vcap_api_next_lookup_advanced_test()
take several hundred bytes of stack frame, but when CONFIG_KASAN_STACK
is enabled, each one of them also has extra padding before and after
it, which ends up blowing the warning limit:
In file included from drivers/net/ethernet/microchip/vcap/vcap_api.c:3521:
drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c: In function 'vcap_api_next_lookup_advanced_test':
drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:1954:1: error: the frame size of 1448 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
1954 | }
Reduce the total stack usage by replacing the five structures with
an array that only needs one pair of padding areas.
Fixes: 1f741f001160 ("net: microchip: sparx5: Add KUNIT tests for enabling/disabling chains")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides these 3 actions for rule in the ES0 VCAP: - action vlan pop - action vlan modify id X priority Y - action vlan push id X priority Y protocol Z Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This enables the TC command to use the Sparx5 ES0 VCAP, and handling of rule links between IS0 and ES0. Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>