On port initialization, we configure the maximum frame length accepted
by the receive module associated with the port. This value is currently
written to the MAX_LEN field of the DEV10G_MAC_ENA_CFG register, when in
fact, it should be written to the DEV10G_MAC_MAXLEN_CFG register. Fix
this.
Fixes: 946e7fd5053a ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing port mirroring, the physical port to send the frame to, is
written to the FRMC_PORT_VAL field of the QFWD_FRAME_COPY_CFG register.
This field is 7 bits wide on sparx5 and 6 bits wide on lan969x, and has
a default value of 65 and 30, respectively (the number of front ports).
On mirror deletion, we set the default value of the monitor port to
65 for this field, in case no more ports exists for the mirror. Needless
to say, this will not fit the 6 bits on lan969x.
Fix this by correctly using the n_ports constant instead.
Fixes: 3f9e46347a46 ("net: sparx5: use SPX5_CONST for constants which already have a symbol")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FDMA handler is responsible for scheduling a NAPI poll, which will
eventually fetch RX packets from the FDMA queue. Currently, the FDMA
handler is run in a threaded context. For some reason, this kills
performance. Admittedly, I did not do a thorough investigation to see
exactly what causes the issue, however, I noticed that in the other
driver utilizing the same FDMA engine, we run the FDMA handler in hard
IRQ context.
Fix this performance issue, by running the FDMA handler in hard IRQ
context, not deferring any work to a thread.
Prior to this change, the RX UDP performance was:
Interval Transfer Bitrate Jitter
0.00-10.20 sec 44.6 MBytes 36.7 Mbits/sec 0.027 ms
After this change, the rx UDP performance is:
Interval Transfer Bitrate Jitter
0.00-9.12 sec 1.01 GBytes 953 Mbits/sec 0.020 ms
Fixes: 10615907e9b5 ("net: sparx5: switchdev: adding frame DMA functionality")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are mixing the use of spin_lock() and spin_lock_irqsave() functions
in the PTP handler of lan969x. Fix this by correctly using the _irqsave
variants.
Fixes: 24fe83541755 ("net: lan969x: add PTP handler function")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
[1]: https://lore.kernel.org/netdev/20241024-sparx5-lan969x-switch-driver-2-v2-10-a0b5fae88a0f@microchip.com/
Signed-off-by: David S. Miller <davem@davemloft.net>
Depmod reports a cyclic dependency between modules sparx5-switch.ko and
lan969x-switch.ko:
depmod: ERROR: Cycle detected: lan969x_switch -> sparx5_switch -> lan969x_switch
depmod: ERROR: Found 2 modules in dependency cycles!
make[2]: *** [scripts/Makefile.modinst:132: depmod] Error 1
make: *** [Makefile:224: __sub-make] Error 2
This makes sense, as they both require symbols from each other.
Fix this by compiling lan969x support into the sparx5-switch.ko module.
In order to do this, in a sensible way, we move the lan969x/ dir into
the sparx5/ dir and do some code cleanup of code that is no longer
required.
After this patch, depmod will no longer complain, as lan969x support is
compiled into the sparx5-swicth.ko module, and can no longer be compiled
as a standalone module.
Fixes: 98a01119608d ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP API unit tests fail randomly with errors such as
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:387
Expected 134 + 7 == iter.offset, but
134 + 7 == 141 (0x8d)
iter.offset == 17214 (0x433e)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:388
Expected 5 == iter.reg_idx, but
iter.reg_idx == 702 (0x2be)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:389
Expected 11 == iter.reg_bitpos, but
iter.reg_bitpos == 15 (0xf)
# vcap_api_iterator_init_test: pass:0 fail:1 skip:0 total:1
Comments in the code state that "A typegroup table ends with an all-zero
terminator". Add the missing terminators.
Some of the typegroups did have a terminator of ".offset = 0, .width = 0,
.value = 0,". Replace those terminators with "{ }" (no trailing ',') for
consistency and to excplicitly state "this is a terminator".
Fixes: 67d637516fa9 ("net: microchip: sparx5: Adding KUNIT test for the VCAP API")
Cc: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119213202.2884639-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sparx5 switchdev driver can be built either with or without support
for the Lan969x switch. However, it cannot be built-in when the lan969x
driver is a loadable module because of a link-time dependency:
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/sparx5/sparx5_main.o:(.rodata+0xd44): undefined reference to `lan969x_desc'
Add a Kconfig dependency to reflect this in Kconfig, allowing all
the valid configurations but forcing sparx5 to be a loadable module
as well if lan969x is.
Fixes: 98a01119608d ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241113115513.4132548-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add configuration data (for consumption by the VCAP API) for the four VCAP's that we are going to support. The following VCAP's will be supported: - VCAP CLM: (also known as IS0) is part of the analyzer and enables frame classification using VCAP functionality. - VCAP IS2: is part of ANA_ACL and enables access control lists, using VCAP functionality. - VCAP ES0: is part of the rewriter and enables rewriting of frames using VCAP functionality. - VCAP ES2: is part of EACL and enables egress access control lists using VCAP functionality The two VCAP's: CLM and IS2 use shared resources from the SUPER VCAP. The SUPER VCAP is a shared pool of 6 blocks that can be distributed freely among CLM and IS2. Each block in the pool has 3,072 addresses with entries, actions, and counters. ES0 and ES2 does not use shared resources. In the configuration data for lan969x CLM uses blocks 2-4 with a total of 6 lookups. IS2 uses blocks 0-1 with a total of 4 lookups. Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Platform VCAP data for each VCAP instance is auto-generated using an internal Microchip tool. The generated VCAP data contains information about keyfields, keyfield sets, actionfields, actionfield sets and typegroups, which in combination are used to encode and decode rules in the VCAP. Add the auto-generated VCAP file lan969x_vcap_ag_api.c and assign the two structs: lan969x_vcaps and lan969x_vcap_stats to the match data. Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The is_sparx5() check was introduced in an earlier series, to make sure the sparx5_vcap_init() was not executed on lan969x, as it was not implemented there yet. Now that it is, remove that check. Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>