Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.

Fixes: 9cde94506eacf ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On 64bits kernels, device stats are 64bits wide, not 32bits.

Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bgmac_open() calls phy_start() to initialize the PHY state machine,
which will set the interface's carrier state accordingly, no need to
force that as this could be conflicting with the PHY state determined by
PHYLIB.

Fixes: dd4544f05469 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver does not start the transmit queue in bgmac_open(). If the
queue was stopped prior to closing then re-opening the interface, we
would never be able to wake-up again.

Fixes: dd4544f05469 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are checking for the Start of Frame bit in the ctl1 word, while this
bit is set in the ctl0 word instead. Read the ctl0 word and update the
check to verify that.

Fixes: 9cde94506eac ("bgmac: implement scatter/gather support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since both CTAG and STAG rx acceleration must be enabled together, we
only need to check one feature flag (NETIF_F_HW_VLAN_CTAG_RX) before
calling __vlan_hwaccel_put_tag().

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware can only be set to strip or not strip both the VLAN CTAG and
STAG.  It cannot strip one and not strip the other.  Add logic to
bnxt_fix_features() to toggle both feature flags when the user is toggling
one of them.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the is_push flag in the software BD before the tx data is pushed to
the chip.  It is possible to get the tx interrupt as soon as the tx data
is pushed.  The tx handler will not handle the event properly if the
is_push flag is not set and it will crash.

Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since implementing VLAN filtering in commit 05cc5a39ddb74
("bnx2x: add vlan filtering offload") bnx2x refuses to add a VLAN while
the interface is down:

  # ip link add link enp3s0f0 enp3s0f0_10 type vlan id 10
  RTNETLINK answers: Bad address

and in dmesg (with bnx2x.debug=0x20):
  bnx2x: [bnx2x_vlan_rx_add_vid:12941(enp3s0f0)]Ignoring VLAN
  configuration the interface is down

Other drivers have no problem with this.
Fix this peculiar behavior in the following way:
 - Accept requests to add/kill VID regardless of the device state.
   Maintain the requested list of VIDs in the bp->vlan_reg list.
 - If the device is up, try to configure the VID list into the hardware.
   If we run out of VLAN credits or encounter a failure configuring an
   entry, fall back to accepting all VLANs.
   If we successfully configure all entries from the list, turn the
   fallback off.
 - Use the same code for reconfiguring VLANs during NIC load.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>