linux-stable.git/drivers/net/dsa, branch v6.2.9

net: dsa: mt7530: move setting ssc_delta to PHY_INTERFACE_MODE_TRGMII case

2023-03-30T10:51:22+00:00

[ Upstream commit 407b508bdd70b6848993843d96ed49ac4108fb52 ]

Move setting the ssc_delta variable to under the PHY_INTERFACE_MODE_TRGMII
case as it's only needed when trgmii is used.

Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL 
Link: https://lore.kernel.org/r/20230320190520.124513-3-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: mt7530: move lowering TRGMII driving to mt7530_setup()

2023-03-30T10:51:22+00:00

[ Upstream commit fdcc8ccd823740c18e803b886cec461bc0e64201 ]

Move lowering the TRGMII Tx clock driving to mt7530_setup(), after setting
the core clock, as seen on the U-Boot MediaTek ethernet driver.

Move the code which looks like it lowers the TRGMII Rx clock driving to
after the TRGMII Tx clock driving is lowered. This is run after lowering
the Tx clock driving on the U-Boot MediaTek ethernet driver as well.

This way, the switch should consume less power regardless of port 6 being
used.

Update the comment explaining mt7530_pad_clk_setup().

Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.

Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: https://source.denx.de/u-boot/u-boot/-/blob/29a48bf9ccba45a5e560bb564bbe76e42629325f/drivers/net/mtk_eth.c#L682
Tested-by: Arınç ÜNAL 
Signed-off-by: Arınç ÜNAL 
Link: https://lore.kernel.org/r/20230320190520.124513-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: mt7530: move enabling disabling core clock to mt7530_pll_setup()

2023-03-30T10:51:22+00:00

[ Upstream commit 8f058a6ef99f0b88a177b58cc46a44ff5112e40a ]

Split the code that enables and disables TRGMII clocks and core clock.
Move enabling and disabling core clock to mt7530_pll_setup() as it's
supposed to be run there.

Add 20 ms delay before enabling the core clock as seen on the U-Boot
MediaTek ethernet driver.

Change the comment for enabling and disabling TRGMII clocks as the code
seems to affect both TXC and RXC.

Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.

Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: https://source.denx.de/u-boot/u-boot/-/blob/29a48bf9ccba45a5e560bb564bbe76e42629325f/drivers/net/mtk_eth.c#L589
Tested-by: Arınç ÜNAL 
Signed-off-by: Arınç ÜNAL 
Link: https://lore.kernel.org/r/20230320190520.124513-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: b53: mmap: fix device tree support

2023-03-30T10:50:53+00:00

[ Upstream commit 30796d0dcb6e41c6558a07950f2ce60c209da867 ]

CPU port should also be enabled in order to get a working switch.

Fixes: a5538a777b73 ("net: dsa: b53: mmap: Add device tree support")
Signed-off-by: Álvaro Fernández Rojas 
Acked-by: Florian Fainelli 
Link: https://lore.kernel.org/r/20230316172807.460146-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: microchip: fix RGMII delay configuration on KSZ8765/KSZ8794/KSZ8795

2023-03-22T12:37:53+00:00

[ Upstream commit 5ae06327a3a5bad4ee246d81df203b1b00a7b390 ]

The blamed commit has replaced a ksz_write8() call to address
REG_PORT_5_CTRL_6 (0x56) with a ksz_set_xmii() -> ksz_pwrite8() call to
regs[P_XMII_CTRL_1], which is also defined as 0x56 for ksz8795_regs[].

The trouble is that, when compared to ksz_write8(), ksz_pwrite8() also
adjusts the register offset with the port base address. So in reality,
ksz_pwrite8(offset=0x56) accesses register 0x56 + 0x50 = 0xa6, which in
this switch appears to be unmapped, and the RGMII delay configuration on
the CPU port does nothing.

So if the switch wasn't fine with the RGMII delay configuration done
through pin strapping and relied on Linux to apply a different one in
order to pass traffic, this is now broken.

Using the offset translation logic imposed by ksz_pwrite8(), the correct
value for regs[P_XMII_CTRL_1] should have been 0x6 on ksz8795_regs[], in
order to really end up accessing register 0x56.

Static code analysis shows that, despite there being multiple other
accesses to regs[P_XMII_CTRL_1] in this driver, the only code path that
is applicable to ksz8795_regs[] and ksz8_dev_ops is ksz_set_xmii().
Therefore, the problem is isolated to RGMII delays.

In its current form, ksz8795_regs[] contains the same value for
P_XMII_CTRL_0 and for P_XMII_CTRL_1, and this raises valid suspicions
that writes made by the driver to regs[P_XMII_CTRL_0] might overwrite
writes made to regs[P_XMII_CTRL_1] or vice versa.

Again, static analysis shows that the only accesses to P_XMII_CTRL_0
from the driver are made from code paths which are not reachable with
ksz8_dev_ops. So the accesses made by ksz_set_xmii() are safe for this
switch family.

[ vladimiroltean: rewrote commit message ]

Fixes: c476bede4b0f ("net: dsa: microchip: ksz8795: use common xmii function")
Signed-off-by: Marek Vasut 
Signed-off-by: Vladimir Oltean 
Acked-by: Arun Ramadoss 
Reviewed-by: Florian Fainelli 
Link: https://lore.kernel.org/r/20230315231916.2998480-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290

2023-03-22T12:37:52+00:00

[ Upstream commit 7e9517375a14f44ee830ca1c3278076dd65fcc8f ]

There are 3 classes of switch families that the driver is aware of, as
far as mv88e6xxx_change_mtu() is concerned:

- MTU configuration is available per port. Here, the
chip->info->ops->port_set_jumbo_size() method will be present.

- MTU configuration is global to the switch. Here, the
chip->info->ops->set_max_frame_size() method will be present.

- We don't know how to change the MTU. Here, none of the above methods
will be present.

Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290
fall in category 3.

The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN
(8 bytes), resulting in a new maximum MTU of 1492 being reported by the
driver for these switches.

I don't have the hardware to test, but I do have a MV88E6390 switch on
which I can simulate this by commenting out its .port_set_jumbo_size
definition from mv88e6390_ops. The result is this set of messages at
probe time:

mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8

It is highly implausible that there exist Ethernet switches which don't
support the standard MTU of 1500 octets, and this is what the DSA
framework says as well - the error comes from dsa_slave_create() ->
dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN).

But the error messages are alarming, and it would be good to suppress
them.

As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu()
and mv88e6xxx_change_mtu() on switches from the 3rd category as follows:
the maximum supported MTU is 1500, and any request to set the MTU to a
value larger than that fails in dev_validate_mtu().

Fixes: b9c587fed61c ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports")
Signed-off-by: Vladimir Oltean
Reviewed-by: Simon Horman
Reviewed-by: Florian Fainelli
Signed-off-by: David S. Miller
Signed-off-by: Sasha Levin

net: dsa: mt7530: set PLL frequency and trgmii only when trgmii is used

2023-03-22T12:37:47+00:00

[ Upstream commit 0b086d76e7b011772b0ac214c6e5fd5816eff2df ]

As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL
frequency does not affect MII modes other than trgmii on port 5 and port 6.
So the assumption is that the operation here called "setting the PLL
frequency" actually sets the frequency of the TRGMII TX clock.

Make it so that it and the rest of the trgmii setup run only when the
trgmii mode is used.

Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec
U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2.

Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Tested-by: Arınç ÜNAL 
Signed-off-by: Arınç ÜNAL 
Link: https://lore.kernel.org/r/20230310073338.5836-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: mt7530: remove now incorrect comment regarding port 5

2023-03-22T12:37:47+00:00

[ Upstream commit feb03fd11c5616f3a47e4714d2f9917d0f1a2edd ]

Remove now incorrect comment regarding port 5 as GMAC5. This is supposed to
be supported since commit 38f790a80560 ("net: dsa: mt7530: Add support for
port 5") under mt7530_setup_port5().

Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Arınç ÜNAL 
Link: https://lore.kernel.org/r/20230310073338.5836-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC

2023-03-17T07:57:59+00:00

[ Upstream commit c8b8a3c601f2cfad25ab5ce5b04df700048aef6e ]

The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).

Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.

The call path that triggers the register write is:

mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
   -> mt7530_pad_clk_setup()

so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.

The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe359 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.

Testing confirms that:

- the slight reordering of writes to MT7530_P6ECR and to
  CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
  appear to cause problems for the operation of port 6 on MT7621 and on
  MT7623 (where port 5 also always worked)

- packets sent through port 5 are not corrupted anymore, regardless of
  whether port 6 is enabled by phylink or not (or even present in the
  device tree)

My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a80560 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909db ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.

Thanks go to Arınç for describing the problem, for debugging and for
testing.

Reported-by: Arınç ÜNAL 
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean 
Tested-by: Arınç ÜNAL 
Reviewed-by: Simon Horman 
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski 
Signed-off-by: Sasha Levin

net: dsa: felix: fix internal MDIO controller resource length

2023-03-11T12:50:34+00:00

[ Upstream commit 940af261321307cd1dd0fe8f9c34a6129f9d4bdc ]

The blamed commit did not properly convert the resource start/end format
into the DEFINE_RES_MEM_NAMED() start/length format, resulting in a
resource for vsc9959_imdio_res which is much longer than expected:

$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
  1f8140000-1f815ffff : 0000:00:00.5
    1f8148030-1f815006f : imdio

vs (correct)

$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
  1f8140000-1f815ffff : 0000:00:00.5
    1f8148030-1f814803f : imdio

Luckily it's not big enough to exceed the size of the parent resource
(pci_resource_end(pdev, VSC9959_IMDIO_PCI_BAR)), and it doesn't overlap
with anything else that the Linux driver uses currently, so the larger
than expected size isn't a practical problem that I can see. Although it
is clearly wrong in the /proc/iomem output.

Fixes: 044d447a801f ("net: dsa: felix: use DEFINE_RES_MEM_NAMED for resources")
Signed-off-by: Vladimir Oltean 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin