ATU Load operations could fail silently if there's not enough space
on the device to hold the new entry. When this happens, the symptom
depends on the unknown flood settings. If unknown multicast flood is
disabled, the multicast packets are dropped when the ATU table is
full. If unknown multicast flood is enabled, the multicast packets
will be flooded to all ports. Either way, IGMP snooping is broken
when the ATU Load operation fails silently.
Do a Read-After-Write verification after each fdb/mdb add operation
to make sure that the operation was really successful, and return
-ENOSPC otherwise.
Fixes: defb05b9b9b4 ("net: dsa: mv88e6xxx: Add support for fdb_add, fdb_del, and fdb_getnext")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250306172306.3859214-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On MMIO devices (e.g. MT7988 or EN7581) unicast traffic received on lanX
port is flooded on all other user ports if the DSA switch is configured
without VLAN support since PORT_MATRIX in PCR regs contains all user
ports. Similar to MDIO devices (e.g. MT7530 and MT7531) fix the issue
defining default VLAN-ID 0 for MT7530 MMIO devices.
Fixes: 110c18bfed414 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20250304-mt7988-flooding-fix-v1-1-905523ae83e9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make NET_DSA_REALTEK_RTL8366RB_LEDS a hidden symbol. It seems very unlikely user would want to intentionally disable it. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Link: https://patch.msgid.link/20250228004534.3428681-1-kuba@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d617005475 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from Paolo Abeni:
"This is slightly smaller than usual, with the most interesting work
being still around RTNL scope reduction.
Core:
- More core refactoring to reduce the RTNL lock contention, including
preparatory work for the per-network namespace RTNL lock, replacing
RTNL lock with a per device-one to protect NAPI-related net device
data and moving synchronize_net() calls outside such lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge
and more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter:
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on each
restart.
Protocols:
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets, to
avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel TLS
(for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API:
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W
implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling:
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec, to ease
maintenance and future development.
- Add YNL support for decoding the link types used in net self-tests,
allowing a single build to run both net and drivers/net.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues,
affecting both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station
mode support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync"
* tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1386 commits)
net/rose: prevent integer overflows in rose_setsockopt()
net: phylink: fix regression when binding a PHY
net: ethernet: ti: am65-cpsw: streamline TX queue creation and cleanup
net: ethernet: ti: am65-cpsw: streamline RX queue creation and cleanup
net: ethernet: ti: am65-cpsw: ensure proper channel cleanup in error path
ipv6: Convert inet6_rtm_deladdr() to per-netns RTNL.
ipv6: Convert inet6_rtm_newaddr() to per-netns RTNL.
ipv6: Move lifetime validation to inet6_rtm_newaddr().
ipv6: Set cfg.ifa_flags before device lookup in inet6_rtm_newaddr().
ipv6: Pass dev to inet6_addr_add().
ipv6: Convert inet6_ioctl() to per-netns RTNL.
ipv6: Hold rtnl_net_lock() in addrconf_init() and addrconf_cleanup().
ipv6: Hold rtnl_net_lock() in addrconf_dad_work().
ipv6: Hold rtnl_net_lock() in addrconf_verify_work().
ipv6: Convert net.ipv6.conf.${DEV}.XXX sysctl to per-netns RTNL.
ipv6: Add __in6_dev_get_rtnl_net().
net: stmmac: Drop redundant skb_mark_for_recycle() for SKB frags
net: mii: Fix the Speed display when the network cable is not connected
sysctl net: Remove macro checks for CONFIG_SYSCTL
eth: bnxt: update header sizing defaults
...
Pull kthread updates from Frederic Weisbecker:
"Kthreads affinity follow either of 4 existing different patterns:
1) Per-CPU kthreads must stay affine to a single CPU and never
execute relevant code on any other CPU. This is currently handled
by smpboot code which takes care of CPU-hotplug operations.
Affinity here is a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and
can't run anywhere else. The affinity is set through
kthread_bind_mask() and the subsystem takes care by itself to
handle CPU-hotplug operations. Affinity here is assumed to be a
correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node.
This is not a correctness constraint but merely a preference in
terms of memory locality. kswapd and kcompactd both fall into this
category. The affinity is set manually like for any other task and
CPU-hotplug is supposed to be handled by the relevant subsystem so
that the task is properly reaffined whenever a given CPU from the
node comes up. Also care should be taken so that the node affinity
doesn't cross isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its
own ad-hoc way.
This is an infrastructure proposal to handle this with the following
API changes:
- kthread_create_on_node() automatically affines the created kthread
to its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called
right after kthread_create_on_node() to specify a preferred
affinity different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine to
the housekeeping CPUs (which means to all online CPUs most of the time
or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
- Consolidate a bunch of ad-hoc implementations of
kthread_run_on_cpu()
- Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
- Add some correctness check to ensure kthread_bind() is always
called before the first kthread wake up.
- Default affine kthread to its preferred node.
- Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
- Implement kthreads preferred affinity
- Unify kthread worker and kthread API's style
- Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation"
* tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks:
kthread: modify kernel-doc function name to match code
rcu: Use kthread preferred affinity for RCU exp kworkers
treewide: Introduce kthread_run_worker[_on_cpu]()
kthread: Unify kthread_create_on_cpu() and kthread_create_worker_on_cpu() automatic format
rcu: Use kthread preferred affinity for RCU boost
kthread: Implement preferred affinity
mm: Create/affine kswapd to its preferred node
mm: Create/affine kcompactd to its preferred node
kthread: Default affine kthread to its preferred NUMA node
kthread: Make sure kthread hasn't started while binding it
sched,arm64: Handle CPU isolation on last resort fallback rq selection
arm64: Exclude nohz_full CPUs from 32bits el0 support
lib: test_objpool: Use kthread_run_on_cpu()
kallsyms: Use kthread_run_on_cpu()
soc/qman: test: Use kthread_run_on_cpu()
arm/bL_switcher: Use kthread_run_on_cpu()
Replace ternary (condition ? "enable" : "disable") syntax with helpers from string_choices.h because: 1. Simple function call with one argument is easier to read. Ternary operator has three arguments and with wrapping might lead to quite long code. 2. Is slightly shorter thus also easier to read. 3. It brings uniformity in the text - same string. 4. Allows deduping by the linker, which results in a smaller binary file. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Make the linkage between the DSA user port ethtool_ops :: get_ts_info and the implementation from the Ocelot switch library. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Link: https://patch.msgid.link/20250116104628.123555-5-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the current neg_mode into the .pcs_get_state() method. Update all users of phylink PCS. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The use of of_property_read_bool() for non-boolean properties is deprecated in favor of of_property_present() when testing for property presence. Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>