linux-stable.git/drivers/net/dsa, branch v4.20

net: dsa: mv88e6xxx: set ethtool regs version

2018-12-18T07:29:00+00:00

Currently the ethtool_regs version is set to 0 for all DSA drivers.

Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.

Signed-off-by: Vivien Didelot 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

mv88e6060: disable hardware level MAC learning

2018-12-04T00:04:21+00:00

Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.

Signed-off-by: Anderson Luiz Alves 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: dsa: mv88e6xxx: Fix clearing of stats counters

2018-11-11T18:19:10+00:00

The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.

Reported-by: Chris Healy 
Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: dsa: microchip: initialize mutex before use

2018-11-03T06:56:34+00:00

Initialize mutex before use.  Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.

Fixes: b987e98e50ab90e5 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha 
Reviewed-by: Pavel Machek 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: dsa: qca8k: simplify getting .driver_data

2018-10-22T04:10:11+00:00

We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: dsa: bcm_sf2: simplify getting .driver_data

2018-10-22T04:10:11+00:00

We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: dsa: mv88e6xxx: Fix 88E6141/6341 2500mbps SERDES speed

2018-10-18T04:56:15+00:00

This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.

On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.

Signed-off-by: Marek Behún 
Signed-off-by: David S. Miller

net: dsa: bcm_sf2: Call setup during switch resume

2018-10-11T05:53:03+00:00

There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.

Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: dsa: bcm_sf2: Fix unbind ordering

2018-10-11T05:53:02+00:00

The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.

Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.

Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2018-10-06T21:43:42+00:00