Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.

In both cases code was added on both sides in the same place
so just keep both.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).

Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().

Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
   \--ksz_switch_register()
      +--dsa_register_switch()
      |  \--dsa_switch_probe()
      |     \--dsa_tree_setup()
      |        \--dsa_tree_setup_switches()
      |           +--dsa_switch_setup()
      |           |  +--ksz9477_setup()
      |           |  |  \--ksz_init_mib_timer()
      |           |  |     |--/* Start the timer 2 seconds later. */
      |           |  |     \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
      |           |  \--__mdiobus_register()
      |           |     \--mdiobus_scan()
      |           |        \--get_phy_device()
      |           |           +--get_phy_id()
      |           |           \--phy_device_create()
      |           |              |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
      |           |              \--request_module()
      |           |
      |           \--dsa_port_setup()
      |              +--/* Called for non-CPU ports */
      |              +--dsa_slave_create()
      |              |  +--/* Too late, ksz_mib_read_work() may be called beforehand */
      |              |  \--port->slave = ...
      |             ...
      |              +--Called for CPU port */
      |              \--dsa_port_link_register_of()
      |                 \--ksz_mac_link_down()
      |                    +--/* mib_read must be initialized here */
      |                    +--/* work is already scheduled, so it will be executed after 2000 ms */
      |                    \--schedule_delayed_work(&dev->mib_read, 0);
      \-- /* here port->slave is setup properly, scheduling the delayed work should be safe */

Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.

Fixes: 7c6ff470aa86 ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.

Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rejecting non-native endian BTF overlapped with the addition
of support for it.

The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.

Signed-off-by: David S. Miller <davem@davemloft.net>

A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
  (the DSA framework just checks for the presence of the .port_vlan_add
  and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime

Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.

So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.

Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous implementation failed to account for the "ports" node. The
actual port nodes are not child nodes of the switch node, but a "ports"
node sits in between.

Fixes: edecfa98f602 ("net: dsa: microchip: look for phy-mode in port nodes")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two minor conflicts:

1) net/ipv4/route.c, adding a new local variable while
   moving another local variable and removing it's
   initial assignment.

2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
   One pretty prints the port mode differently, whilst another
   changes the driver to try and obtain the port mode from
   the port node rather than the switch node.

Signed-off-by: David S. Miller <davem@davemloft.net>

The KSZ9477 and KSZ8795 use the port_cnt field differently: For the
KSZ9477, it includes the CPU port(s), while for the KSZ8795, it doesn't.

It would be a good cleanup to make the handling of both drivers match,
but as a first step, fix the recently broken assignment of num_ports in
the KSZ8795 driver (which completely broke probing, as the CPU port
index was always failing the num_ports check).

Fixes: af199a1a9cb0 ("net: dsa: microchip: set the correct number of ports")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/dsa/dsa.txt says that the phy-mode
property should be specified on port nodes. However, the microchip
drivers read it from the switch node.

Let the driver use the per-port property and fall back to the old
location with a warning.

Fix in-tree users.

Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Link: https://lore.kernel.org/netdev/20200617082235.GA1523@laureti-dev/
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The datasheet for the ksz9893 and ksz9477 switches recommend waiting at
least 100us after the de-assertion of reset before trying to program the
device through any interface.

Also switch the existing msleep() call to usleep_range() as recommended
in Documentation/timers/timers-howto.rst. The 2ms range used here is
somewhat arbitrary, as long as the reset is asserted for at least 10ms
we should be ok.

Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>