linux-stable.git/drivers/net/bonding, branch v5.8.4

bonding: fix active-backup failover for current ARP slave

2020-08-26T09:49:17+00:00

[ Upstream commit 0410d07190961ac526f05085765a8d04d926545b ]

When the ARP monitor is used for link detection, ARP replies are
validated for all slaves (arp_validate=3) and fail_over_mac is set to
active, two slaves of an active-backup bond may get stuck in a state
where both of them are active and pass packets that they receive to
the bond. This state makes IPv6 duplicate address detection fail. The
state is reached thus:
1. The current active slave goes down because the ARP target
   is not reachable.
2. The current ARP slave is chosen and made active.
3. A new slave is enslaved. This new slave becomes the current active
   slave and can reach the ARP target.
As a result, the current ARP slave stays active after the enslave
action has finished and the log is littered with "PROBE BAD" messages:
> bond0: PROBE: c_arp ens10 && cas ens11 BAD
The workaround is to remove the slave with "going back" status from
the bond and re-enslave it. This issue was encountered when DPDK PMD
interfaces were being enslaved to an active-backup bond.

I would be possible to fix the issue in bond_enslave() or
bond_change_active_slave() but the ARP monitor was fixed instead to
keep most of the actions changing the current ARP slave in the ARP
monitor code. The current ARP slave is set as inactive and backup
during the commit phase. A new state, BOND_LINK_FAIL, has been
introduced for slaves in the context of the ARP monitor. This allows
administrators to see how slaves are rotated for sending ARP requests
and attempts are made to find a new active slave.

Fixes: b2220cad583c9 ("bonding: refactor ARP active-backup monitor")
Signed-off-by: Jiri Wiesner 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bonding: fix a potential double-unregister

2020-08-26T09:49:11+00:00

[ Upstream commit 832707021666411d04795c564a4adea5d6b94f17 ]

When we tear down a network namespace, we unregister all
the netdevices within it. So we may queue a slave device
and a bonding device together in the same unregister queue.

If the only slave device is non-ethernet, it would
automatically unregister the bonding device as well. Thus,
we may end up unregistering the bonding device twice.

Workaround this special case by checking reg_state.

Fixes: 9b5e383c11b0 ("net: Introduce unregister_netdevice_many()")
Reported-by: syzbot+af23e7f3e0a7e10c8b67@syzkaller.appspotmail.com
Cc: Eric Dumazet 
Cc: Andy Gospodarek 
Cc: Jay Vosburgh 
Signed-off-by: Cong Wang 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bonding: show saner speed for broadcast mode

2020-08-26T09:49:11+00:00

[ Upstream commit 4ca0d9ac3fd8f9f90b72a15d8da2aca3ffb58418 ]

Broadcast mode bonds transmit a copy of all traffic simultaneously out of
all interfaces, so the "speed" of the bond isn't really the aggregate of
all interfaces, but rather, the speed of the slowest active interface.

Also, the type of the speed field is u32, not unsigned long, so adjust
that accordingly, as required to make min() function here without
complaining about mismatching types.

Fixes: bb5b052f751b ("bond: add support to read speed and duplex via ethtool")
CC: Jay Vosburgh 
CC: Veaceslav Falico 
CC: Andy Gospodarek 
CC: "David S. Miller" 
CC: netdev@vger.kernel.org
Acked-by: Jay Vosburgh 
Signed-off-by: Jarod Wilson 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

bonding: check return value of register_netdevice() in bond_newlink()

2020-07-23T22:17:04+00:00

Very similar to commit 544f287b8495
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.

Fixes: 005db31d5f5f ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani 
Cc: Taehee Yoo 
Cc: Jay Vosburgh 
Signed-off-by: Cong Wang 
Signed-off-by: David S. Miller

bonding: check error value of register_netdevice() immediately

2020-07-20T01:12:21+00:00

If register_netdevice() is failed, net_device should not be used
because variables are uninitialized or freed.
So, the routine should be stopped immediately.
But, bond_create() doesn't check return value of register_netdevice()
immediately. That will result in a panic because of using uninitialized
or freed memory.

Test commands:
    modprobe netdev-notifier-error-inject
    echo -22 > /sys/kernel/debug/notifier-error-inject/netdev/\
actions/NETDEV_REGISTER/error
    modprobe bonding max_bonds=3

Splat looks like:
[  375.028492][  T193] general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[  375.033207][  T193] CPU: 2 PID: 193 Comm: kworker/2:2 Not tainted 5.8.0-rc4+ #645
[  375.036068][  T193] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[  375.039673][  T193] Workqueue: events linkwatch_event
[  375.041557][  T193] RIP: 0010:dev_activate+0x4a/0x340
[  375.043381][  T193] Code: 40 a8 04 0f 85 db 00 00 00 8b 83 08 04 00 00 85 c0 0f 84 0d 01 00 00 31 d2 89 d0 48 8d 04 40 48 c1 e0 07 48 03 83 00 04 00 00 <48> 8b 48 10 f6 41 10 01 75 08 f0 80 a1 a0 01 00 00 fd 48 89 48 08
[  375.050267][  T193] RSP: 0018:ffff9f8facfcfdd8 EFLAGS: 00010202
[  375.052410][  T193] RAX: 6b6b6b6b6b6b6b6b RBX: ffff9f8fae6ea000 RCX: 0000000000000006
[  375.055178][  T193] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9f8fae6ea000
[  375.057762][  T193] RBP: ffff9f8fae6ea000 R08: 0000000000000000 R09: 0000000000000000
[  375.059810][  T193] R10: 0000000000000001 R11: 0000000000000000 R12: ffff9f8facfcfe08
[  375.061892][  T193] R13: ffffffff883587e0 R14: 0000000000000000 R15: ffff9f8fae6ea580
[  375.063931][  T193] FS:  0000000000000000(0000) GS:ffff9f8fbae00000(0000) knlGS:0000000000000000
[  375.066239][  T193] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  375.067841][  T193] CR2: 00007f2f542167a0 CR3: 000000012cee6002 CR4: 00000000003606e0
[  375.069657][  T193] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  375.071471][  T193] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  375.073269][  T193] Call Trace:
[  375.074005][  T193]  linkwatch_do_dev+0x4d/0x50
[  375.075052][  T193]  __linkwatch_run_queue+0x10b/0x200
[  375.076244][  T193]  linkwatch_event+0x21/0x30
[  375.077274][  T193]  process_one_work+0x252/0x600
[  375.078379][  T193]  ? process_one_work+0x600/0x600
[  375.079518][  T193]  worker_thread+0x3c/0x380
[  375.080534][  T193]  ? process_one_work+0x600/0x600
[  375.081668][  T193]  kthread+0x139/0x150
[  375.082567][  T193]  ? kthread_park+0x90/0x90
[  375.083567][  T193]  ret_from_fork+0x22/0x30

Fixes: e826eafa65c6 ("bonding: Call netif_carrier_off after register_netdevice")
Signed-off-by: Taehee Yoo 
Signed-off-by: David S. Miller

net: change addr_list_lock back to static key

2020-06-09T19:59:45+00:00

The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:

CPU 0:				CPU 1:
(RCU read lock)			(RTNL lock)
dev_mc_seq_show()		netdev_update_lockdep_key()
				  -> lockdep_unregister_key()
 -> netif_addr_lock_bh()

because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.

In commit 1a33e10e4a95 ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc22f
("net: core: add generic lockdep keys").

This patch reverts the rest and also part of commit f3b0a18bb6cb
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().

And hopefully this reduces some syzbot lockdep noises too.

Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo 
Cc: Dmitry Vyukov 
Signed-off-by: Cong Wang 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2020-06-01T00:48:46+00:00

xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.

The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.

Signed-off-by: David S. Miller

bonding: Fix reference count leak in bond_sysfs_slave_add.

2020-05-28T18:08:16+00:00

kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.

Fixes: 07699f9a7c8d ("bonding: add sysfs /slave dir for bond slave devices.")
Signed-off-by: Qiushi Wu 
Acked-by: Jay Vosburgh 
Signed-off-by: David S. Miller

Merge branch 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux

2020-05-09T08:05:30+00:00

This merge includes updates to bonding driver needed for the rdma stack,
to avoid conflicts with the RDMA branch.

Maor Gottlieb Says:

====================
Bonding: Add support to get xmit slave

The following series adds support to get the LAG master xmit slave by
introducing new .ndo - ndo_get_xmit_slave. Every LAG module can
implement it and it first implemented in the bond driver.
This is follow-up to the RFC discussion [1].

The main motivation for doing this is for drivers that offload part
of the LAG functionality. For example, Mellanox Connect-X hardware
implements RoCE LAG which selects the TX affinity when the resources
are created and port is remapped when it goes down.

The first part of this patchset introduces the new .ndo and add the
support to the bonding module.

The second part adds support to get the RoCE LAG xmit slave by building
skb of the RoCE packet based on the AH attributes and call to the new
.ndo.

The third part change the mlx5 driver driver to set the QP's affinity
port according to the slave which found by the .ndo.
====================

Signed-off-by: Saeed Mahameed

bonding: propagate transmit status

2020-05-08T01:11:07+00:00

Currently, bonding always returns NETDEV_TX_OK to its caller.

It is worth trying to be more accurate : TCP for instance
can have different recovery strategies if it can have more
precise status, if packet was dropped by slave qdisc.

This is especially important when host is under stress.

Signed-off-by: Eric Dumazet 
Cc: Jay Vosburgh 
Cc: Veaceslav Falico 
Cc: Andy Gospodarek 
Signed-off-by: David S. Miller