linux-stable.git/drivers/mmc, branch v5.4.40 Linux kernel stable tree mmc: meson-mx-sdio: remove the broken ->card_busy() op 2020-05-06T06:15:07+00:00 Martin Blumenstingl martin.blumenstingl@googlemail.com 2020-04-16T18:35:13+00:00 ca34751b58196e86cf8c6b5b911ee3cb174d151a commit ddca1092c4324c89cf692b5efe655aa251864b51 upstream. The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard") makes use of the ->card_busy() op for SD cards. This uncovered that the ->card_busy() op in the Meson SDIO driver was never working right: while polling the busy status with ->card_busy() meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC register values 0x1f001f10 or 0x1f003f10. This translates to "three out of four DAT lines are HIGH" and "all four DAT lines are HIGH", which is interpreted as "the card is busy". It turns out that no situation can be observed where all four DAT lines are LOW, meaning the card is not busy anymore. Upon further research the 3.10 vendor driver for this controller does not implement the ->card_busy() op. Remove the ->card_busy() op from the meson-mx-sdio driver since it is not working. At the time of writing this patch it is not clear what's needed to make the ->card_busy() implementation work with this specific controller hardware. For all use-cases which have previously worked the MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have a ->card_busy() op anymore. Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ddca1092c4324c89cf692b5efe655aa251864b51 upstream.

The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".

It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.

Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.

Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: meson-mx-sdio: Set MMC_CAP_WAIT_WHILE_BUSY 2020-05-06T06:15:07+00:00 Martin Blumenstingl martin.blumenstingl@googlemail.com 2020-04-16T18:35:12+00:00 9e3315116f7e294fa9333df09f00455ec9340b2e commit e53b868b3cf5beeaa2f851ec6740112bf4d6a8cb upstream. The Meson SDIO controller uses the DAT0 lane for hardware busy detection. Set MMC_CAP_WAIT_WHILE_BUSY accordingly. This fixes the following error observed with Linux 5.7 (pre-rc-1): mmc1: Card stuck being busy! __mmc_poll_for_busy blk_update_request: I/O error, dev mmcblk1, sector 17111080 op 0x3:(DISCARD) flags 0x0 phys_seg 1 prio class 0 Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200416183513.993763-2-martin.blumenstingl@googlemail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e53b868b3cf5beeaa2f851ec6740112bf4d6a8cb upstream.

The Meson SDIO controller uses the DAT0 lane for hardware busy
detection. Set MMC_CAP_WAIT_WHILE_BUSY accordingly. This fixes
the following error observed with Linux 5.7 (pre-rc-1):
  mmc1: Card stuck being busy! __mmc_poll_for_busy
  blk_update_request: I/O error, dev mmcblk1, sector 17111080 op
   0x3:(DISCARD) flags 0x0 phys_seg 1 prio class 0

Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: sdhci-msm: Enable host capabilities pertains to R1b response 2020-05-06T06:15:06+00:00 Veerabhadrarao Badiganti vbadigan@codeaurora.org 2020-04-20T06:20:23+00:00 80e99f42608d0dba763c85e3d96bdee2e00f5c43 commit 9d8cb58691f85cef687512262acb2c7109ee4868 upstream. MSM sd host controller is capable of HW busy detection of device busy signaling over DAT0 line. And it requires the R1B response for commands that have this response associated with them. So set the below two host capabilities for qcom SDHC. - MMC_CAP_WAIT_WHILE_BUSY - MMC_CAP_NEED_RSP_BUSY Recent development of the mmc core in regards to this, revealed this as being a potential bug, hence the stable tag. Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9d8cb58691f85cef687512262acb2c7109ee4868 upstream.

MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.

So set the below two host capabilities for qcom SDHC.
 - MMC_CAP_WAIT_WHILE_BUSY
 - MMC_CAP_NEED_RSP_BUSY

Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.

Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: sdhci-pci: Fix eMMC driver strength for BYT-based controllers 2020-05-06T06:15:06+00:00 Adrian Hunter adrian.hunter@intel.com 2020-04-22T11:16:29+00:00 d8f7e15a65ddb8e6bba1fdebac3d86c2c2d89dc1 commit 1a8eb6b373c2af6533c13d1ea11f504e5010ed9a upstream. BIOS writers have begun the practice of setting 40 ohm eMMC driver strength even though the eMMC may not support it, on the assumption that the kernel will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH [offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid. This is done to avoid changing the value for different boards. Putting aside the merits of this approach, it is clear the eMMC's mask of supported driver strengths is more reliable than the value provided by BIOS. Add validation accordingly. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 51ced59cc02e ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1a8eb6b373c2af6533c13d1ea11f504e5010ed9a upstream.

BIOS writers have begun the practice of setting 40 ohm eMMC driver strength
even though the eMMC may not support it, on the assumption that the kernel
will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH
[offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid.

This is done to avoid changing the value for different boards.

Putting aside the merits of this approach, it is clear the eMMC's mask
of supported driver strengths is more reliable than the value provided
by BIOS. Add validation accordingly.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 51ced59cc02e ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: sdhci-xenon: fix annoying 1.8V regulator warning 2020-05-06T06:15:06+00:00 Marek Behún marek.behun@nic.cz 2020-04-20T08:04:44+00:00 eed4792f96575b91fabf9da3dab6e5bf894238d0 commit bb32e1987bc55ce1db400faf47d85891da3c9b9f upstream. For some reason the Host Control2 register of the Xenon SDHCI controller sometimes reports the bit representing 1.8V signaling as 0 when read after it was written as 1. Subsequent read reports 1. This causes the sdhci_start_signal_voltage_switch function to report 1.8V regulator output did not become stable When CONFIG_PM is enabled, the host is suspended and resumend many times, and in each resume the switch to 1.8V is called, and so the kernel log reports this message annoyingly often. Do an empty read of the Host Control2 register in Xenon's .voltage_switch method to circumvent this. This patch fixes this particular problem on Turris MOX. Signed-off-by: Marek Behún <marek.behun@nic.cz> Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...") Cc: stable@vger.kernel.org # v4.16+ Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit bb32e1987bc55ce1db400faf47d85891da3c9b9f upstream.

For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.

This causes the sdhci_start_signal_voltage_switch function to report
  1.8V regulator output did not become stable

When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.

Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.

This patch fixes this particular problem on Turris MOX.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...")
Cc: stable@vger.kernel.org # v4.16+
Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: cqhci: Avoid false "cqhci: CQE stuck on" by not open-coding timeout loop 2020-05-06T06:15:06+00:00 Douglas Anderson dianders@chromium.org 2020-04-13T23:27:27+00:00 31ba94b893b6e4f4ca45ddb0a6ecc3199655c861 commit b1ac62a7ac386d76968af5f374a4a7a82a35fe31 upstream. Open-coding a timeout loop invariably leads to errors with handling the timeout properly in one corner case or another. In the case of cqhci we might report "CQE stuck on" even if it wasn't stuck on. You'd just need this sequence of events to happen in cqhci_off(): 1. Call ktime_get(). 2. Something happens to interrupt the CPU for > 100 us (context switch or interrupt). 3. Check time and; set "timed_out" to true since > 100 us. 4. Read CQHCI_CTL. 5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break. 6. Since "timed_out" is true, falsely print the error message. Rather than fixing the polling loop, use readx_poll_timeout() like many people do. This has been time tested to handle the corner cases. Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b1ac62a7ac386d76968af5f374a4a7a82a35fe31 upstream.

Open-coding a timeout loop invariably leads to errors with handling
the timeout properly in one corner case or another.  In the case of
cqhci we might report "CQE stuck on" even if it wasn't stuck on.
You'd just need this sequence of events to happen in cqhci_off():

1. Call ktime_get().
2. Something happens to interrupt the CPU for > 100 us (context switch
   or interrupt).
3. Check time and; set "timed_out" to true since > 100 us.
4. Read CQHCI_CTL.
5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break.
6. Since "timed_out" is true, falsely print the error message.

Rather than fixing the polling loop, use readx_poll_timeout() like
many people do.  This has been time tested to handle the corner cases.

Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: sdhci: Refactor sdhci_set_timeout() 2020-04-17T08:50:25+00:00 Faiz Abbas faiz_abbas@ti.com 2020-01-16T10:51:50+00:00 26711cc7e0641781e696c775fa84f7415ff49b4e [ Upstream commit 7d76ed77cfbd39468ae58d419f537d35ca892d83 ] Refactor sdhci_set_timeout() such that platform drivers can do some functionality in a set_timeout() callback and then call __sdhci_set_timeout() to complete the operation. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200116105154.7685-7-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7d76ed77cfbd39468ae58d419f537d35ca892d83 ]

Refactor sdhci_set_timeout() such that platform drivers can do some
functionality in a set_timeout() callback and then call
__sdhci_set_timeout() to complete the operation.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-7-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: sdhci: Convert sdhci_set_timeout_irq() to non-static 2020-04-17T08:50:25+00:00 Faiz Abbas faiz_abbas@ti.com 2020-01-16T10:51:49+00:00 56a296657e4bab76b1eb192d6ea7204e55810361 [ Upstream commit 7907ebe741a7f14ed12889ebe770438a4ff47613 ] Export sdhci_set_timeout_irq() so that it is accessible from platform drivers. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200116105154.7685-6-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7907ebe741a7f14ed12889ebe770438a4ff47613 ]

Export sdhci_set_timeout_irq() so that it is accessible from platform drivers.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: sdhci-of-esdhc: fix esdhc_reset() for different controller versions 2020-04-17T08:50:16+00:00 Yangbo Lu yangbo.lu@nxp.com 2020-01-08T04:07:12+00:00 e0ae9da3fb2fed45fdd437cea6c597044c02dc47 commit 2aa3d826adb578b26629a79b775a552cfe3fedf7 upstream. This patch is to fix operating in esdhc_reset() for different controller versions, and to add bus-width restoring after data reset for eSDHC (verdor version <= 2.2). Also add annotation for understanding. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200108040713.38888-1-yangbo.lu@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2aa3d826adb578b26629a79b775a552cfe3fedf7 upstream.

This patch is to fix operating in esdhc_reset() for different
controller versions, and to add bus-width restoring after data
reset for eSDHC (verdor version <= 2.2).

Also add annotation for understanding.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108040713.38888-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: sdhci-tegra: Fix busy detection by enabling MMC_CAP_NEED_RSP_BUSY 2020-04-01T09:01:29+00:00 Ulf Hansson ulf.hansson@linaro.org 2020-03-24T18:07:38+00:00 127882d109316bc2cc18af931c9f9cdaf0ad98e0 [ Upstream commit d2f8bfa4bff5028bc40ed56b4497c32e05b0178f ] It has turned out that the sdhci-tegra controller requires the R1B response, for commands that has this response associated with them. So, converting from an R1B to an R1 response for a CMD6 for example, leads to problems with the HW busy detection support. Fix this by informing the mmc core about the requirement, via setting the host cap, MMC_CAP_NEED_RSP_BUSY. Reported-by: Bitan Biswas <bbiswas@nvidia.com> Reported-by: Peter Geis <pgwipeout@gmail.com> Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Tested-By: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit d2f8bfa4bff5028bc40ed56b4497c32e05b0178f ]

It has turned out that the sdhci-tegra controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.

Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.

Reported-by: Bitan Biswas <bbiswas@nvidia.com>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>