linux-stable.git/drivers/mmc, branch v5.4.158

mmc: sdhci-esdhc-imx: clear the buffer_read_ready to reset standard tuning circuit

2021-11-02T18:46:12+00:00

commit 9af372dc70e9fdcbb70939dac75365e7b88580b4 upstream.

To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.

Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.

Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: Map more voltage level to SDHCI_POWER_330

2021-11-02T18:46:12+00:00

commit 4217d07b9fb328751f877d3bd9550122014860a2 upstream.

On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V),
which is being treated as an invalid value by sdhci_set_power_noreg().
And thus eMMC is totally broken on the platform.

[    1.436599] ------------[ cut here ]------------
[    1.436606] mmc0: Invalid vdd 0x17
[    1.436640] WARNING: CPU: 2 PID: 69 at drivers/mmc/host/sdhci.c:2048 sdhci_set_power_noreg+0x168/0x2b4
[    1.436655] Modules linked in:
[    1.436662] CPU: 2 PID: 69 Comm: kworker/u8:1 Tainted: G        W         5.15.0-rc1+ #137
[    1.436669] Hardware name: Thundercomm TurboX CM2290 (DT)
[    1.436674] Workqueue: events_unbound async_run_entry_fn
[    1.436685] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    1.436692] pc : sdhci_set_power_noreg+0x168/0x2b4
[    1.436698] lr : sdhci_set_power_noreg+0x168/0x2b4
[    1.436703] sp : ffff800010803a60
[    1.436705] x29: ffff800010803a60 x28: ffff6a9102465f00 x27: ffff6a9101720a70
[    1.436715] x26: ffff6a91014de1c0 x25: ffff6a91014de010 x24: ffff6a91016af280
[    1.436724] x23: ffffaf7b1b276640 x22: 0000000000000000 x21: ffff6a9101720000
[    1.436733] x20: ffff6a9101720370 x19: ffff6a9101720580 x18: 0000000000000020
[    1.436743] x17: 0000000000000000 x16: 0000000000000004 x15: ffffffffffffffff
[    1.436751] x14: 0000000000000000 x13: 00000000fffffffd x12: ffffaf7b1b84b0bc
[    1.436760] x11: ffffaf7b1b720d10 x10: 000000000000000a x9 : ffff800010803a60
[    1.436769] x8 : 000000000000000a x7 : 000000000000000f x6 : 00000000fffff159
[    1.436778] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000ffffffff
[    1.436787] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff6a9101718d80
[    1.436797] Call trace:
[    1.436800]  sdhci_set_power_noreg+0x168/0x2b4
[    1.436805]  sdhci_set_ios+0xa0/0x7fc
[    1.436811]  mmc_power_up.part.0+0xc4/0x164
[    1.436818]  mmc_start_host+0xa0/0xb0
[    1.436824]  mmc_add_host+0x60/0x90
[    1.436830]  __sdhci_add_host+0x174/0x330
[    1.436836]  sdhci_msm_probe+0x7c0/0x920
[    1.436842]  platform_probe+0x68/0xe0
[    1.436850]  really_probe.part.0+0x9c/0x31c
[    1.436857]  __driver_probe_device+0x98/0x144
[    1.436863]  driver_probe_device+0xc8/0x15c
[    1.436869]  __device_attach_driver+0xb4/0x120
[    1.436875]  bus_for_each_drv+0x78/0xd0
[    1.436881]  __device_attach_async_helper+0xac/0xd0
[    1.436888]  async_run_entry_fn+0x34/0x110
[    1.436895]  process_one_work+0x1d0/0x354
[    1.436903]  worker_thread+0x13c/0x470
[    1.436910]  kthread+0x150/0x160
[    1.436915]  ret_from_fork+0x10/0x20
[    1.436923] ---[ end trace fcfac44cb045c3a8 ]---

Fix the issue by mapping MMC_VDD_35_36 (and MMC_VDD_34_35) to
SDHCI_POWER_330 as well.

Signed-off-by: Shawn Guo 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211004024935.15326-1-shawn.guo@linaro.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: dw_mmc: exynos: fix the finding clock sample value

2021-11-02T18:46:12+00:00

commit 697542bceae51f7620af333b065dd09d213629fb upstream.

Even though there are candiates value if can't find best value, it's
returned -EIO. It's not proper behavior.
If there is not best value, use a first candiate value to work eMMC.

Signed-off-by: Jaehoon Chung 
Tested-by: Marek Szyprowski 
Tested-by: Christian Hewitt 
Cc: stable@vger.kernel.org
Fixes: c537a1c5ff63 ("mmc: dw_mmc: exynos: add variable delay tuning sequence")
Link: https://lore.kernel.org/r/20211022082106.1557-1-jh80.chung@samsung.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: cqhci: clear HALT state after CQE enable

2021-11-02T18:46:12+00:00

commit 92b18252b91de567cd875f2e84722b10ab34ee28 upstream.

While mmc0 enter suspend state, we need halt CQE to send legacy cmd(flush
cache) and disable cqe, for resume back, we enable CQE and not clear HALT
state.
In this case MediaTek mmc host controller will keep the value for HALT
state after CQE disable/enable flow, so the next CQE transfer after resume
will be timeout due to CQE is in HALT state, the log as below:
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: timeout for tag 2
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Caps:      0x100020b6 | Version:  0x00000510
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Config:    0x00001103 | Control:  0x00000001
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int stat:  0x00000000 | Int enab: 0x00000006
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int sig:   0x00000006 | Int Coal: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: TDL base:  0xfd05f000 | TDL up32: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Doorbell:  0x8000203c | TCN:      0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Task clr:  0x00000000 | SSC1:     0x00001000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: SSC2:      0x00000001 | DCMD rsp: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: RED mask:  0xfdf9a080 | TERRI:    0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Resp idx:  0x00000000 | Resp arg: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQP:     0x00000000 | CRNQDUN:  0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQIS:    0x00000000 | CRNQIE:   0x00000000

This change check HALT state after CQE enable, if CQE is in HALT state, we
will clear it.

Signed-off-by: Wenbin Mei 
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter 
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Link: https://lore.kernel.org/r/20211026070812.9359-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: vub300: fix control-message timeouts

2021-11-02T18:46:12+00:00

commit 8c8171929116cc23f74743d99251eedadf62341a upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org      # 3.0
Signed-off-by: Johan Hovold 
Link: https://lore.kernel.org/r/20211025115608.5287-1-johan@kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: meson-gx: do not use memcpy_to/fromio for dram-access-quirk

2021-10-13T08:08:16+00:00

commit 8a38a4d51c5055d0201542e5ea3c0cb287f6e223 upstream.

The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.

Add a local copy using writel/readl accesses to make sure we use the right
memory access width.

The switch to memcpy_to/fromio was done because of 285133040e6c
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.

Fixes: 103a5348c22c ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk")
Reported-by: Christian Hewitt 
Suggested-by: Martin Blumenstingl 
Signed-off-by: Neil Armstrong 
Tested-by: Martin Blumenstingl 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: core: Return correct emmc response in case of ioctl error

2021-09-22T10:26:35+00:00

[ Upstream commit e72a55f2e5ddcfb3dce0701caf925ce435b87682 ]

When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.

IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)

The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).

It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.

Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().

The test code and the output of only the CMD17 is included in the
commit to limit the message length.

CMD17 (Test Code Snippet):
==========================
        printf("Forming CMD%d\n", opt_idx);
        /*  single block read */
        cmd.blksz = 512;
        cmd.blocks = 1;
        cmd.write_flag = 0;
        cmd.opcode = 17;
        //cmd.arg = atoi(argv[3]);
        cmd.arg = 0x09B2FFFF;
        /* Expecting response R1B */
        cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;

        memset(data, 0, sizeof(__u8) * 512);
        mmc_ioc_cmd_set_data(cmd, data);

        printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
        if(ioctl(fd, MMC_IOC_CMD, &cmd))
                perror("Error");

        printf("\nResponse: %08x\n", cmd.response[0]);

CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out

Response: 00000000
(Incorrect response)

CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out

Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)

Signed-off-by: Nishad Kamdar 
Reviewed-by: Avri Altman 
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: rtsx_pci: Fix long reads when clock is prescaled

2021-09-22T10:26:34+00:00

[ Upstream commit 3ac5e45291f3f0d699a721357380d4593bc2dcb3 ]

For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.

During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.

This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.

I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.

Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.

Signed-off-by: Thomas Hebb
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson
Signed-off-by: Sasha Levin

mmc: sdhci-of-arasan: Check return value of non-void funtions

2021-09-22T10:26:34+00:00

[ Upstream commit 66bad6ed2204fdb78a0a8fb89d824397106a5471 ]

At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.

Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani 
Acked-by: Adrian Hunter 
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: moxart: Fix issue with uninitialized dma_slave_config

2021-09-15T07:47:36+00:00

[ Upstream commit ee5165354d498e5bceb0b386e480ac84c5f8c28c ]

Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.

For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.

For moxart, this is probably not currently an issue but is still good to
fix though.

Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen 
Cc: Vinod Koul 
Cc: Peter Ujfalusi 
Signed-off-by: Tony Lindgren 
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin