linux-stable.git/drivers/mmc, branch v5.15

mmc: tmio: reenable card irqs after the reset callback

2021-10-28T21:19:32+00:00

The reset callback may clear the internal card detect interrupts, so
make sure to reenable them if needed.

Fixes: b4d86f37eacb ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Biju Das 
Signed-off-by: Wolfram Sang 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211028195149.8003-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson

mmc: mediatek: Move cqhci init behind ungate clock

2021-10-28T09:55:20+00:00

We must enable clock before cqhci init, because crypto needs read
information from CQHCI registers, otherwise, it will hang in MediaTek mmc
host controller.

Signed-off-by: Wenbin Mei 
Fixes: 88bd652b3c74 ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Acked-by: Chaotian Jing 
Link: https://lore.kernel.org/r/20211028022049.22129-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson

mmc: cqhci: clear HALT state after CQE enable

2021-10-26T15:34:57+00:00

While mmc0 enter suspend state, we need halt CQE to send legacy cmd(flush
cache) and disable cqe, for resume back, we enable CQE and not clear HALT
state.
In this case MediaTek mmc host controller will keep the value for HALT
state after CQE disable/enable flow, so the next CQE transfer after resume
will be timeout due to CQE is in HALT state, the log as below:
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: timeout for tag 2
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Caps:      0x100020b6 | Version:  0x00000510
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Config:    0x00001103 | Control:  0x00000001
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int stat:  0x00000000 | Int enab: 0x00000006
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int sig:   0x00000006 | Int Coal: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: TDL base:  0xfd05f000 | TDL up32: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Doorbell:  0x8000203c | TCN:      0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Task clr:  0x00000000 | SSC1:     0x00001000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: SSC2:      0x00000001 | DCMD rsp: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: RED mask:  0xfdf9a080 | TERRI:    0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Resp idx:  0x00000000 | Resp arg: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQP:     0x00000000 | CRNQDUN:  0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQIS:    0x00000000 | CRNQIE:   0x00000000

This change check HALT state after CQE enable, if CQE is in HALT state, we
will clear it.

Signed-off-by: Wenbin Mei 
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter 
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Link: https://lore.kernel.org/r/20211026070812.9359-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson

mmc: vub300: fix control-message timeouts

2021-10-26T15:31:58+00:00

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org      # 3.0
Signed-off-by: Johan Hovold 
Link: https://lore.kernel.org/r/20211025115608.5287-1-johan@kernel.org
Signed-off-by: Ulf Hansson

mmc: dw_mmc: exynos: fix the finding clock sample value

2021-10-26T15:28:41+00:00

Even though there are candiates value if can't find best value, it's
returned -EIO. It's not proper behavior.
If there is not best value, use a first candiate value to work eMMC.

Signed-off-by: Jaehoon Chung 
Tested-by: Marek Szyprowski 
Tested-by: Christian Hewitt 
Cc: stable@vger.kernel.org
Fixes: c537a1c5ff63 ("mmc: dw_mmc: exynos: add variable delay tuning sequence")
Link: https://lore.kernel.org/r/20211022082106.1557-1-jh80.chung@samsung.com
Signed-off-by: Ulf Hansson

mmc: winbond: don't build on M68K

2021-10-19T10:57:11+00:00

The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:

../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
  212 |                 dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
  215 |                 release_dma_lock(dmaflags);

Signed-off-by: Randy Dunlap 
Cc: Pierre Ossman 
Cc: Geert Uytterhoeven 
Cc: Arnd Bergmann 
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson

mmc: sdhci-esdhc-imx: clear the buffer_read_ready to reset standard tuning circuit

2021-10-19T10:46:05+00:00

To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.

Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.

Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson

mmc: sdhci-pci: Read card detect from ACPI for Intel Merrifield

2021-10-14T11:20:17+00:00

Intel Merrifield platform had been converted to use ACPI enumeration.
However, the driver missed an update to retrieve card detect GPIO.
Fix it here.

Unfortunately we can't rely on CD GPIO state because there are two
different PCB designs in the wild that are using the opposite card
detection sense and there is no way to distinguish those platforms,
that's why ignore CD GPIO completely and use it only as an event.

Fixes: 4590d98f5a4f ("sfi: Remove framework for deprecated firmware")
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135
Signed-off-by: Andy Shevchenko 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211013201723.52212-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson

mmc: sdhci: Map more voltage level to SDHCI_POWER_330

2021-10-12T08:20:58+00:00

On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V),
which is being treated as an invalid value by sdhci_set_power_noreg().
And thus eMMC is totally broken on the platform.

[    1.436599] ------------[ cut here ]------------
[    1.436606] mmc0: Invalid vdd 0x17
[    1.436640] WARNING: CPU: 2 PID: 69 at drivers/mmc/host/sdhci.c:2048 sdhci_set_power_noreg+0x168/0x2b4
[    1.436655] Modules linked in:
[    1.436662] CPU: 2 PID: 69 Comm: kworker/u8:1 Tainted: G        W         5.15.0-rc1+ #137
[    1.436669] Hardware name: Thundercomm TurboX CM2290 (DT)
[    1.436674] Workqueue: events_unbound async_run_entry_fn
[    1.436685] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    1.436692] pc : sdhci_set_power_noreg+0x168/0x2b4
[    1.436698] lr : sdhci_set_power_noreg+0x168/0x2b4
[    1.436703] sp : ffff800010803a60
[    1.436705] x29: ffff800010803a60 x28: ffff6a9102465f00 x27: ffff6a9101720a70
[    1.436715] x26: ffff6a91014de1c0 x25: ffff6a91014de010 x24: ffff6a91016af280
[    1.436724] x23: ffffaf7b1b276640 x22: 0000000000000000 x21: ffff6a9101720000
[    1.436733] x20: ffff6a9101720370 x19: ffff6a9101720580 x18: 0000000000000020
[    1.436743] x17: 0000000000000000 x16: 0000000000000004 x15: ffffffffffffffff
[    1.436751] x14: 0000000000000000 x13: 00000000fffffffd x12: ffffaf7b1b84b0bc
[    1.436760] x11: ffffaf7b1b720d10 x10: 000000000000000a x9 : ffff800010803a60
[    1.436769] x8 : 000000000000000a x7 : 000000000000000f x6 : 00000000fffff159
[    1.436778] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000ffffffff
[    1.436787] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff6a9101718d80
[    1.436797] Call trace:
[    1.436800]  sdhci_set_power_noreg+0x168/0x2b4
[    1.436805]  sdhci_set_ios+0xa0/0x7fc
[    1.436811]  mmc_power_up.part.0+0xc4/0x164
[    1.436818]  mmc_start_host+0xa0/0xb0
[    1.436824]  mmc_add_host+0x60/0x90
[    1.436830]  __sdhci_add_host+0x174/0x330
[    1.436836]  sdhci_msm_probe+0x7c0/0x920
[    1.436842]  platform_probe+0x68/0xe0
[    1.436850]  really_probe.part.0+0x9c/0x31c
[    1.436857]  __driver_probe_device+0x98/0x144
[    1.436863]  driver_probe_device+0xc8/0x15c
[    1.436869]  __device_attach_driver+0xb4/0x120
[    1.436875]  bus_for_each_drv+0x78/0xd0
[    1.436881]  __device_attach_async_helper+0xac/0xd0
[    1.436888]  async_run_entry_fn+0x34/0x110
[    1.436895]  process_one_work+0x1d0/0x354
[    1.436903]  worker_thread+0x13c/0x470
[    1.436910]  kthread+0x150/0x160
[    1.436915]  ret_from_fork+0x10/0x20
[    1.436923] ---[ end trace fcfac44cb045c3a8 ]---

Fix the issue by mapping MMC_VDD_35_36 (and MMC_VDD_34_35) to
SDHCI_POWER_330 as well.

Signed-off-by: Shawn Guo 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211004024935.15326-1-shawn.guo@linaro.org
Signed-off-by: Ulf Hansson

Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic

2021-10-08T18:57:54+00:00

Pull asm-generic fixes from Arnd Bergmann:
 "There is one build fix for Arm platforms that ended up impacting most
  architectures because of the way the drivers/firmware Kconfig file is
  wired up:

  The CONFIG_QCOM_SCM dependency have caused a number of randconfig
  regressions over time, and some still remain in v5.15-rc4. The fix we
  agreed on in the end is to make this symbol selected by any driver
  using it, and then building it even for non-Arm platforms with
  CONFIG_COMPILE_TEST.

  To make this work on all architectures, the drivers/firmware/Kconfig
  file needs to be included for all architectures to make the symbol
  itself visible.

  In a separate discussion, we found that a sound driver patch that is
  pending for v5.16 needs the same change to include this Kconfig file,
  so the easiest solution seems to have my Kconfig rework included in
  v5.15.

  Finally, the branch also includes a small unrelated build fix for
  NOMMU architectures"

Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/

* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
  qcom_scm: hide Kconfig symbol
  firmware: include drivers/firmware/Kconfig unconditionally