linux-stable.git/drivers/mmc, branch v4.9.147

MMC: OMAP: fix broken MMC on OMAP15XX/OMAP5910/OMAP310

2018-12-21T13:11:31+00:00

commit e8cde625bfe8a714a856e1366bcbb259d7346095 upstream.

Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.

Before the patch (on Palm TE):

	mmc0: new SD card at address b368
	mmcblk0: mmc0:b368 SDC   977 MiB
	mmci-omap mmci-omap.0: command timeout (CMD18)
	mmci-omap mmci-omap.0: command timeout (CMD13)
	mmci-omap mmci-omap.0: command timeout (CMD13)
	mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
	mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
	mmcblk0: error -110 requesting status
	mmci-omap mmci-omap.0: command timeout (CMD8)
	mmci-omap mmci-omap.0: command timeout (CMD18)
	mmci-omap mmci-omap.0: command timeout (CMD13)
	mmci-omap mmci-omap.0: command timeout (CMD13)
	mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
	mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
	mmcblk0: error -110 requesting status
	mmcblk0: recovery failed!
	print_req_error: I/O error, dev mmcblk0, sector 0
	Buffer I/O error on dev mmcblk0, logical block 0, async page read
	 mmcblk0: unable to read partition table

After the patch:

	mmc0: new SD card at address b368
	mmcblk0: mmc0:b368 SDC   977 MiB
	 mmcblk0: p1

The patch is based on a fix and analysis done by Ladislav Michl.

Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).

[1] https://marc.info/?t=123175197000003&r=1&w=2

Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl 
Reported-by: Andrzej Zaborowski 
Tested-by: Ladislav Michl 
Acked-by: Tony Lindgren 
Signed-off-by: Aaro Koskinen 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01

2018-11-13T19:16:49+00:00

[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ]

This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).

mmc1: Timeout waiting for hardware cmd interrupt.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr:  0x00000000 | Version:  0x00000603
mmc1: sdhci: Blk size:  0x00000000 | Blk cnt:  0x00000000
mmc1: sdhci: Argument:  0x00000000 | Trn mode: 0x00000000
mmc1: sdhci: Present:   0x01ff0001 | Host ctl: 0x00000001
mmc1: sdhci: Power:     0x0000000f | Blk gap:  0x00000000
mmc1: sdhci: Wake-up:   0x00000000 | Clock:    0x0000fa03
mmc1: sdhci: Timeout:   0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab:  0x00ff0083 | Sig enab: 0x00ff0083
mmc1: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps:      0x25fcc8bf | Caps_1:   0x00002077
mmc1: sdhci: Cmd:       0x00000000 | Max curr: 0x005800c8
mmc1: sdhci: Resp[0]:   0x00000000 | Resp[1]:  0x00000000
mmc1: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err:  0x00000000 | ADMA Ptr: 0x00000000
mmc1: sdhci: ============================================

The problem happens during wakeup from S3. Adding a delay quirk
after power up reliably fixes the problem.

Signed-off-by: Yu Zhao 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: do not try to use 3.3V signaling if not supported

2018-09-26T06:36:38+00:00

[ Upstream commit 1b5190c2e74c47ebe4bcecf7a072358ad9f1feaa ]

For eMMC devices it is valid to only support 1.8V signaling. When
vqmmc is set to a fixed 1.8V regulator the stack tries to set 3.3V
initially and prints the following warning:
   mmc1: Switching to 3.3V signalling voltage failed

Clear the MMC_SIGNAL_VOLTAGE_330 flag in case 3.3V is signaling is
not available. This prevents the stack from even trying to use
3.3V signaling and avoids the above warning.

Signed-off-by: Stefan Agner 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: tegra: prevent HS200 on Tegra 3

2018-09-26T06:36:38+00:00

[ Upstream commit 127407e36f4fe3a1d5e8b9998b479956ce83a7dc ]

The stack assumes that SDHC controller which support SD3.0 (SDR104) do
support HS200. This is not the case for Tegra 3, which does support SD
3.0
but only supports eMMC spec 4.41.

Use SDHCI_QUIRK2_BROKEN_HS200 to indicate that the controller does not
support HS200.

Note that commit 156e14b126ff ("mmc: sdhci: fix caps2 for HS200") added
the tie between SD3.0 (SDR104) and HS200. I don't think that this is
necessarly true. It is fully legitimate to support SD3.0 and not support
HS200. The quirk naming suggests something is broken in the controller,
but this is not the case: The controller simply does not support HS200.

Fixes: 7ad2ed1dfcbe ("mmc: tegra: enable UHS-I modes")
Signed-off-by: Stefan Agner 
Tested-by: Marcel Ziswiler 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: omap_hsmmc: fix wakeirq handling on removal

2018-09-26T06:36:35+00:00

commit 3c398f3c3bef21961eaaeb93227fa66d440dc83d upstream.

after unbinding mmc I get things like this:
[  185.294067] mmc1: card 0001 removed
[  185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13

The wakeirq stays in /proc-interrupts

rebinding shows this:
[  289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup)
[  289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ
[  289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling

That bug seems to be introduced by switching from devm_request_irq()
to generic wakeirq handling.

So let us cleanup at removal.

Signed-off-by: Andreas Kemnade 
Fixes: 5b83b2234be6 ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: pwrseq: Use kmalloc_array instead of stack VLA

2018-08-03T05:55:24+00:00

[ Upstream commit 486e6661367b40f927aadbed73237693396cbf94 ]

The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.

Currently driver is using a VLA declared using the number of descriptors.  This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values.  Memory is
free'd before return from function.

>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.

It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`

[1] https://lkml.org/lkml/2018/3/7/621

Signed-off-by: Tobin C. Harding 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: dw_mmc: update actual clock for mmc debugfs

2018-08-03T05:55:24+00:00

[ Upstream commit ff178981bd5fd1667f373098740cb1c6d6efa1ba ]

Respect the actual clock for mmc debugfs to help better debug
the hardware.

mmc_host mmc0: Bus speed (slot 0) = 135475200Hz (slot req 150000000Hz,
actual 135475200HZ div = 0)

cat /sys/kernel/debug/mmc0/ios
clock:          150000000 Hz
actual clock:   135475200 Hz
vdd:            21 (3.3 ~ 3.4 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      3 (8 bits)
timing spec:    9 (mmc HS200)
signal voltage: 0 (1.80 V)
driver type:    0 (driver type B)

Cc: Xiao Yao 
Cc: Ziyuan 
Signed-off-by: Shawn Lin 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: dw_mmc: fix card threshold control configuration

2018-07-17T09:37:51+00:00

commit 7a6b9f4d601dfce8cb68f0dcfd834270280e31e6 upstream.

Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.

Fixes: 7e4bf1bc9543 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia 
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-iproc: fix 32bit writes for TRANSFER_MODE register

2018-05-30T05:50:16+00:00

commit 5f651b870485ee60f5abbbd85195a6852978894a upstream.

When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.

Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban 
Signed-off-by: Scott Branden 
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-iproc: remove hard coded mmc cap 1.8v

2018-05-30T05:50:16+00:00

commit 4c94238f37af87a2165c3fb491b4a8b50e90649c upstream.

Remove hard coded mmc cap 1.8v from platform data as it is board specific.
The 1.8v DDR mmc caps can be enabled using DTS property for those
boards that support it.

Fixes: b17b4ab8ce38 ("mmc: sdhci-iproc: define MMC caps in platform data")
Signed-off-by: Srinath Mannam 
Signed-off-by: Scott Branden 
Reviewed-by: Ray Jui 
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman