linux-stable.git/drivers/mmc, branch v4.4.220

mmc: spi: Toggle SPI polarity, do not hardcode it

2020-02-14T21:29:55+00:00

commit af3ed119329cf9690598c5a562d95dfd128e91d6 upstream.

The code in mmc_spi_initsequence() tries to send a burst with
high chipselect and for this reason hardcodes the device into
SPI_CS_HIGH.

This is not good because the SPI_CS_HIGH flag indicates
logical "asserted" CS not always the physical level. In
some cases the signal is inverted in the GPIO library and
in that case SPI_CS_HIGH is already set, and enforcing
SPI_CS_HIGH again will actually drive it low.

Instead of hard-coding this, toggle the polarity so if the
default is LOW it goes high to assert chipselect but if it
is already high then toggle it low instead.

Cc: Phil Elwell 
Reported-by: Mark Brown 
Signed-off-by: Linus Walleij 
Reviewed-by: Mark Brown 
Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: fix minimum clock rate for v3 controller

2020-01-29T09:21:51+00:00

commit 2a187d03352086e300daa2044051db00044cd171 upstream.

For SDHCIv3+ with programmable clock mode, minimal clock frequency is
still base clock / max(divider). Minimal programmable clock frequency is
always greater than minimal divided clock frequency. Without this patch,
SDHCI uses out-of-spec initial frequency when multiplier is big enough:

mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz
[for 480 MHz source clock divided by 1024]

The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode.

Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode")
Cc:  # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present
Cc: 
Signed-off-by: Michał Mirosław 
Acked-by: Adrian Hunter 
Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: Update the tuning failed messages to pr_debug level

2020-01-04T12:34:38+00:00

[ Upstream commit 2c92dd20304f505b6ef43d206fff21bda8f1f0ae ]

Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d2e ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.

Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.

Signed-off-by: Faiz Abbas 
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-esdhc: fix P2020 errata handling

2020-01-04T12:34:23+00:00

commit fe0acab448f68c3146235afe03fb932e242ec94c upstream.

Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL

The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
	host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
	host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

This patch is to fix them.
	host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
	host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

Fixes: 05cb6b2a66fa ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e42712596 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

Revert "mmc: sdhci: Fix incorrect switch to HS mode"

2020-01-04T12:34:17+00:00

commit 07bcc411567cb96f9d1fc84fff8d387118a2920d upstream.

This reverts commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37.

This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.

The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.

Cc: 
Signed-off-by: Faiz Abbas 
Acked-by: Adrian Hunter 
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: block: Fix tag condition with packed writes

2019-11-28T17:26:15+00:00

commit d806b46e5f496a6335ebd7f8432d2533507ce9a2 upstream.

Apparently a cut-and-paste error, 'do_data_tag' is using 'brq' for data
size even though 'brq' has not been set up. Instead use blk_rq_sectors().

Signed-off-by: Adrian Hunter 
Reviewed-by: Shawn Lin 
Signed-off-by: Ulf Hansson 
Signed-off-by: Lee Jones 
Signed-off-by: Greg Kroah-Hartman

mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready fail

2019-11-28T17:25:38+00:00

[ Upstream commit f38a9774ddde9d79b3487dd888edd8b8623552af ]

when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().

so need call mod_delayed_work() before msdc_cmd_is_ready()

Signed-off-by: Chaotian Jing 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: sdhci-of-at91: fix quirk2 overwrite

2019-11-25T14:53:44+00:00

commit fed23c5829ecab4ddc712d7b0046e59610ca3ba4 upstream.

The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.

Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200")
Signed-off-by: Eugen Hristev 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: Fix incorrect switch to HS mode

2019-10-05T10:27:50+00:00

[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ]

When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.

This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.

The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.

This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.

Suggested-by: Adrian Hunter 
Signed-off-by: Al Cooper 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: core: Fix init of SD cards reporting an invalid VDD range

2019-09-06T08:18:17+00:00

commit 72741084d903e65e121c27bd29494d941729d4a1 upstream.

The OCR register defines the supported range of VDD voltages for SD cards.
However, it has turned out that some SD cards reports an invalid voltage
range, for example having bit7 set.

When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from
the invalid VDD range, this triggers the core to run a power cycle of the
card to try to initialize it at the lowest common supported voltage.
Obviously this fails, since the card can't support it.

Let's fix this problem, by clearing invalid bits from the read OCR register
for SD cards, before proceeding with the VDD voltage negotiation.

Cc: stable@vger.kernel.org
Reported-by: Philip Langdale 
Signed-off-by: Ulf Hansson 
Reviewed-by: Philip Langdale 
Tested-by: Philip Langdale 
Tested-by: Manuel Presnitz 
Signed-off-by: Greg Kroah-Hartman