linux-stable.git/drivers/mmc, branch v4.4.205

mmc: block: Fix tag condition with packed writes

2019-11-28T17:26:15+00:00

commit d806b46e5f496a6335ebd7f8432d2533507ce9a2 upstream.

Apparently a cut-and-paste error, 'do_data_tag' is using 'brq' for data
size even though 'brq' has not been set up. Instead use blk_rq_sectors().

Signed-off-by: Adrian Hunter 
Reviewed-by: Shawn Lin 
Signed-off-by: Ulf Hansson 
Signed-off-by: Lee Jones 
Signed-off-by: Greg Kroah-Hartman

mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready fail

2019-11-28T17:25:38+00:00

[ Upstream commit f38a9774ddde9d79b3487dd888edd8b8623552af ]

when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().

so need call mod_delayed_work() before msdc_cmd_is_ready()

Signed-off-by: Chaotian Jing 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: sdhci-of-at91: fix quirk2 overwrite

2019-11-25T14:53:44+00:00

commit fed23c5829ecab4ddc712d7b0046e59610ca3ba4 upstream.

The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.

Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200")
Signed-off-by: Eugen Hristev 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: Fix incorrect switch to HS mode

2019-10-05T10:27:50+00:00

[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ]

When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.

This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.

The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.

This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.

Suggested-by: Adrian Hunter 
Signed-off-by: Al Cooper 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: core: Fix init of SD cards reporting an invalid VDD range

2019-09-06T08:18:17+00:00

commit 72741084d903e65e121c27bd29494d941729d4a1 upstream.

The OCR register defines the supported range of VDD voltages for SD cards.
However, it has turned out that some SD cards reports an invalid voltage
range, for example having bit7 set.

When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from
the invalid VDD range, this triggers the core to run a power cycle of the
card to try to initialize it at the lowest common supported voltage.
Obviously this fails, since the card can't support it.

Let's fix this problem, by clearing invalid bits from the read OCR register
for SD cards, before proceeding with the VDD voltage negotiation.

Cc: stable@vger.kernel.org
Reported-by: Philip Langdale 
Signed-off-by: Ulf Hansson 
Reviewed-by: Philip Langdale 
Tested-by: Philip Langdale 
Tested-by: Manuel Presnitz 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-at91: add quirk for broken HS200

2019-09-06T08:18:16+00:00

commit 7871aa60ae0086fe4626abdf5ed13eeddf306c61 upstream.

HS200 is not implemented in the driver, but the controller claims it
through caps. Remove it via a quirk, to make sure the mmc core do not try
to enable HS200, as it causes the eMMC initialization to fail.

Signed-off-by: Eugen Hristev 
Acked-by: Ludovic Desroches 
Acked-by: Adrian Hunter 
Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support

2019-06-11T10:24:00+00:00

[ Upstream commit 05cb6b2a66fa7837211a060878e91be5eb10cb07 ]

eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.

Signed-off-by: Yinbo Zhu 
Acked-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: sdhci-of-esdhc: add erratum eSDHC5 support

2019-06-11T10:24:00+00:00

[ Upstream commit a46e42712596b51874f04c73f1cdf1017f88df52 ]

Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.

Signed-off-by: Yinbo Zhu 
Acked-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc_spi: add a status check for spi_sync_locked

2019-06-11T10:24:00+00:00

[ Upstream commit 611025983b7976df0183390a63a2166411d177f1 ]

In case spi_sync_locked fails, the fix reports the error and
returns the error code upstream.

Signed-off-by: Kangjie Lu 
Reviewed-by: Laurent Pinchart 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: core: Verify SD bus width

2019-06-11T10:23:54+00:00

[ Upstream commit 9e4be8d03f50d1b25c38e2b59e73b194c130df7d ]

The SD Physical Layer Spec says the following: Since the SD Memory Card
shall support at least the two bus modes 1-bit or 4-bit width, then any SD
Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101").

This change verifies the card has specified a bus width.

AMD SDHC Device 7806 can get into a bad state after a card disconnect
where anything transferred via the DATA lines will always result in a
zero filled buffer. Currently the driver will continue without error if
the HC is in this condition. A block device will be created, but reading
from it will result in a zero buffer. This makes it seem like the SD
device has been erased, when in actuality the data is never getting
copied from the DATA lines to the data buffer.

SCR is the first command in the SD initialization sequence that uses the
DATA lines. By checking that the response was invalid, we can abort
mounting the card.

Reviewed-by: Avri Altman 
Signed-off-by: Raul E Rangel 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin