linux-stable.git/drivers/mmc, branch v3.18.124

mmc: jz4740: Fix race condition in IRQ mask update

2018-04-24T07:29:26+00:00

commit a04f0017c22453613d5f423326b190c61e3b4f98 upstream.

A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.

If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.

This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).

Resolve by holding the spinlock until after the IMASK register has
been updated.

Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb85687 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre 
Signed-off-by: Alex Smith 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: avoid removing non-removable hosts during suspend

2018-03-24T09:57:35+00:00

[ Upstream commit de8dcc3d2c0e08e5068ee1e26fc46415c15e3637 ]

The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.

After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.

The conditions here are:

 1. During suspend, we reach mmc_pm_notify()

 2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
    suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
    -ENOSYS because btsdio_driver does not have a suspend method.

 3. mmc_pm_notify() proceeds to remove the card

 4. Upon resume, mmc_rescan() does nothing with this host, because of
    the rescan_entered check which aims to only scan a non-removable
    device a single time (i.e. during boot).

Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.

Signed-off-by: Daniel Drake 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: host: omap_hsmmc: checking for NULL instead of IS_ERR()

2018-03-24T09:57:33+00:00

[ Upstream commit ec5ab8933772c87f24ad62a4a602fe8949f423c2 ]

devm_pinctrl_get() returns error pointers, it never returns NULL.

Fixes: 455e5cd6f736 ("mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x")
Signed-off-by: Dan Carpenter 
Reviewed-by: Kishon Vijay Abraham I 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: s3cmci: include linux/interrupt.h for tasklet_struct

2017-11-08T09:03:49+00:00

[ Upstream commit e1c6ec26b853e9062f0b3daaf695c546d0702953 ]

I got this new build error on today's linux-next

drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
  struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]

While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.

Signed-off-by: Arnd Bergmann 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: sdio: fix alignment issue in struct sdio_func

2017-10-08T08:11:21+00:00

[ Upstream commit 5ef1ecf060f28ecef313b5723f1fd39bf5a35f56 ]

Certain 64-bit systems (e.g. Amlogic Meson GX) require buffers to be
used for DMA to be 8-byte-aligned. struct sdio_func has an embedded
small DMA buffer not meeting this requirement.
When testing switching to descriptor chain mode in meson-gx driver
SDIO is broken therefore. Fix this by allocating the small DMA buffer
separately as kmalloc ensures that the returned memory area is
properly aligned for every basic data type.

Signed-off-by: Heiner Kallweit 
Tested-by: Helmut Klein 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: sunxi: avoid invalid pointer calculation

2017-04-30T03:49:16+00:00

commit d34712d2e3db9b241d0484a6e3839c6b7ef9df78 upstream.

The sunxi mmc driver tries to calculate a dma address by using pointer
arithmetic, which causes a warning when dma_addr_t is wider than a pointer:

drivers/mmc/host/sunxi-mmc.c: In function 'sunxi_mmc_init_idma_des':
drivers/mmc/host/sunxi-mmc.c:296:35: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  struct sunxi_idma_des *pdes_pa = (struct sunxi_idma_des *)host->sg_dma;
                                   ^

To avoid this warning and to simplify the logic, this changes
the code to avoid the cast and calculate the correct address
manually. The behavior should be unchanged.

Signed-off-by: Arnd Bergmann 
Acked-by: David Lanzendörfer 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: increase the pad I/O drive strength for DDR50 card

2017-04-30T03:49:13+00:00

commit 9f327845358d3dd0d8a5a7a5436b0aa5c432e757 upstream.

Currently for DDR50 card, it need tuning in default. We meet tuning fail
issue for DDR50 card and some data CRC error when DDR50 sd card works.

This is because the default pad I/O drive strength can't make sure DDR50
card work stable. So increase the pad I/O drive strength for DDR50 card,
and use pins_100mhz.

This fixes DDR50 card support for IMX since DDR50 tuning was enabled from
commit 9faac7b95ea4 ("mmc: sdhci: enable tuning for DDR50")

Tested-and-reported-by: Tim Harvey 
Signed-off-by: Haibo Chen 
Acked-by: Dong Aisheng 
Acked-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: Do not disable interrupts while waiting for clock

2017-04-22T05:15:05+00:00

commit e2ebfb2142acefecc2496e71360f50d25726040b upstream.

Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.

The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.

Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.

Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Tested-by: Ludovic Desroches 
Signed-off-by: Greg Kroah-Hartman

mmc: ushc: fix NULL-deref at probe

2017-04-22T05:15:04+00:00

commit 181302dc7239add8ab1449c23ecab193f52ee6ab upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: 53f3a9e26ed5 ("mmc: USB SD Host Controller (USHC) driver")
Cc: David Vrabel 
Signed-off-by: Johan Hovold 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: Fix recovery from tuning timeout

2017-01-15T14:49:50+00:00

[ Upstream commit 61e53bd0047d58caee0c7170613045bf96de4458 ]

Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.

Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.

Note that this replaces the commit fe5fb2e3b58f ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.

Signed-off-by: Adrian Hunter 
Tested-by: Dan O'Donovan 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin