linux-stable.git/drivers/mmc, branch v3.16.35

mmc: sdhci: fix data timeout (part 2)

2016-04-30T22:05:51+00:00

commit 7f05538af71c7d30b5fc821cbe9f318edc645961 upstream.

The calculation for the timeout based on the number of card clocks is
incorrect.  The calculation assumed:

	timeout in microseconds = clock cycles / clock in Hz

which is clearly a several orders of magnitude wrong.  Fix this by
multiplying the clock cycles by 1000000 prior to dividing by the Hz
based clock.  Also, as per part 1, ensure that the division rounds
up.

As this needs 64-bit math via do_div(), avoid it if the clock cycles
is zero.

Signed-off-by: Russell King 
Signed-off-by: Adrian Hunter 
Tested-by: Gregory CLEMENT 
Signed-off-by: Ulf Hansson 
Signed-off-by: Ben Hutchings

mmc: sdhci: fix data timeout (part 1)

2016-04-30T22:05:51+00:00

commit fafcfda9e78cae8796d1799f14e6457790797555 upstream.

The data timeout gives the minimum amount of time that should be
waited before timing out if no data is received from the card.
Simply dividing the nanosecond part by 1000 does not give this
required guarantee, since such a division rounds down.  Use
DIV_ROUND_UP() to give the desired timeout.

Signed-off-by: Russell King 
Signed-off-by: Adrian Hunter 
Tested-by: Gregory CLEMENT 
Signed-off-by: Ulf Hansson 
Signed-off-by: Ben Hutchings

mmc: debugfs: correct wrong voltage value

2016-02-03T00:04:01+00:00

commit 0036e74686344f1051afc3107740140abfd03616 upstream.

Correct the wrong voltage value shown in debugfs for mmc/sd/sdio.

Signed-off-by: Chuanxiao Dong 
Signed-off-by: Pawel Wodkowski 
Fixes: 42cd95a0603e ("mmc: core: debugfs: Add signal_voltage to ios dump")
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques

mmc: sd: limit SD card power limit according to cards capabilities

2016-02-02T23:34:15+00:00

commit d9812780a020bcec44565b5950b2a8b31afb5545 upstream.

The SD card specification allows cards to error out a SWITCH command
where the requested function in a group is not supported.  The spec
provides for a set of capabilities which indicate which functions are
supported.

In the case of the power limit, requesting an unsupported power level
via the SWITCH command fails, resulting in the power level remaining at
the power-on default of 0.72W, even though the host and card may support
higher powers levels.

This has been seen with SanDisk 8GB cards, which support the default
0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host,
supporting up to 2.88W (800mA).  This currently causes us to try to set
a power limit function value of '3' (2.88W) which the card errors out
on, and thereby causes the power level to remain at 0.72W rather than
the desired 1.44W.

Arrange to limit the selected current limit by the capabilities reported
by the card to avoid the SWITCH command failing.  Select the highest
current limit that the host and card combination support.

Signed-off-by: Russell King 
Fixes: a39ca6ae0a08 ("mmc: core: Simplify and fix for SD switch processing")
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques

mmc: mmci: fix an ages old detection error

2016-02-02T19:09:39+00:00

commit 0bcb7efdff63564e80fe84dd36a9fbdfbf6697a4 upstream.

commit 4956e10903fd ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.

Fixes: 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik...")
Signed-off-by: Linus Walleij 
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques

mmc: sdhci: Fix sdhci_runtime_pm_bus_on/off()

2016-02-02T17:38:45+00:00

commit 5c671c410c8704800f4f1673b6f572137e7e6ddd upstream.

sdhci has a legacy facility to prevent runtime suspend if the
bus power is on.  This is needed in cases where the power to
the card is dependent on the bus power.  It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off().  These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem.  In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume.  So remove  the check.

Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques

mmc: sdio: Fix invalid vdd in voltage switch power cycle

2016-02-02T17:38:44+00:00

commit d9bfbb95ed598a09cf336adb0f190ee0ff802f0d upstream.

The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage.  However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd.  Fix by passing the card's
ocr value which does not have the flag.

Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques

mmc: remove bondage between REQ_META and reliable write

2015-12-14T10:17:12+00:00

commit d3df0465db00cf4ed9f90d0bfc3b827d32b9c796 upstream.

Anytime a write operation is performed with Reliable Write flag enabled,
the eMMC device is enforced to bypass the cache and do a write to the
underling NVM device by Jedec specification; this causes a performance
penalty since write operations can't be optimized by the device cache.

In our tests, we replayed a typical mobile daily trace pattern and found
~9% overall time reduction in trace replay by using this patch. Also the
write ops within 4KB~64KB chunk size range get a 40~60% performance
improvement by using the patch (as this range of write chunks are the ones
affected by REQ_META).

This patch has been discussed in the Mobile & Embedded Linux Storage Forum
and it's the results of feedbacks from many people. We also checked with
fsdevl and f2fs mailing list developers that this change in the usage of
REQ_META is not affecting FS behavior and we got positive feedbacks.
Reporting here the feedbacks:
http://comments.gmane.org/gmane.linux.file-systems/97219
http://thread.gmane.org/gmane.linux.file-systems.f2fs/3178/focus=3183

Signed-off-by: Bruce Ford 
Signed-off-by: Luca Porzio 
Fixes: ce39f9d17c14 ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques

mmc: core: fix race condition in mmc_wait_data_done

2015-09-30T12:20:49+00:00

commit 71f8a4b81d040b3d094424197ca2f1bf811b1245 upstream.

The following panic is captured in ker3.14, but the issue still exists
in latest kernel.
---------------------------------------------------------------------
[   20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference
at virtual address 00000578
......
[   20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60
[   20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60
[   20.740134] c0 3136 (Compiler) Call trace:
[   20.740165] c0 3136 (Compiler) [] _raw_spin_lock_irqsave+0x24/0x60
[   20.740200] c0 3136 (Compiler) [] __wake_up+0x1c/0x54
[   20.740230] c0 3136 (Compiler) [] mmc_wait_data_done+0x28/0x34
[   20.740262] c0 3136 (Compiler) [] mmc_request_done+0xa4/0x220
[   20.740314] c0 3136 (Compiler) [] sdhci_tasklet_finish+0xac/0x264
[   20.740352] c0 3136 (Compiler) [] tasklet_action+0xa0/0x158
[   20.740382] c0 3136 (Compiler) [] __do_softirq+0x10c/0x2e4
[   20.740411] c0 3136 (Compiler) [] irq_exit+0x8c/0xc0
[   20.740439] c0 3136 (Compiler) [] handle_IRQ+0x48/0xac
[   20.740469] c0 3136 (Compiler) [] gic_handle_irq+0x38/0x7c
----------------------------------------------------------------------
Because in SMP, "mrq" has race condition between below two paths:
path1: CPU0: 
  static void mmc_wait_data_done(struct mmc_request *mrq)
  {
     mrq->host->context_info.is_done_rcv = true;
     //
     // If CPU0 has just finished "is_done_rcv = true" in path1, and at
     // this moment, IRQ or ICache line missing happens in CPU0.
     // What happens in CPU1 (path2)?
     //
     // If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode:
     // path2 would have chance to break from wait_event_interruptible
     // in mmc_wait_for_data_req_done and continue to run for next
     // mmc_request (mmc_blk_rw_rq_prep).
     //
     // Within mmc_blk_rq_prep, mrq is cleared to 0.
     // If below line still gets host from "mrq" as the result of
     // compiler, the panic happens as we traced.
     wake_up_interruptible(&mrq->host->context_info.wait);
  }

path2: CPU1: 
  static int mmc_wait_for_data_req_done(...
  {
     ...
     while (1) {
           wait_event_interruptible(context_info->wait,
                   (context_info->is_done_rcv ||
                    context_info->is_new_req));
     	   static void mmc_blk_rw_rq_prep(...
           {
           ...
           memset(brq, 0, sizeof(struct mmc_blk_request));

This issue happens very coincidentally; however adding mdelay(1) in
mmc_wait_data_done as below could duplicate it easily.

   static void mmc_wait_data_done(struct mmc_request *mrq)
   {
     mrq->host->context_info.is_done_rcv = true;
+    mdelay(1);
     wake_up_interruptible(&mrq->host->context_info.wait);
    }

At runtime, IRQ or ICache line missing may just happen at the same place
of the mdelay(1).

This patch gets the mmc_context_info at the beginning of function, it can
avoid this race condition.

Signed-off-by: Jialing Fu 
Tested-by: Shawn Lin 
Fixes: 2220eedfd7ae ("mmc: fix async request mechanism ....")
Signed-off-by: Shawn Lin 
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques

mmc: sdhci: also get preset value and driver type for MMC_DDR52

2015-09-30T12:20:46+00:00

commit 0dafa60eb2506617e6968b97cc5a44914a7fb1a6 upstream.

commit bb8175a8aa42 ("mmc: sdhci: clarify DDR timing mode between
SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be
distinguished from SD-UHS, but it missed setting driver type for
MMC_DDR52 timing mode.

So sometimes we get the following error on Marvell BG2Q DMP board:

[    1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd
response 0x900, card status 0xb00
[    1.569314] mmcblk0: retrying using single block read
[    1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd
response 0x900, card status 0x0
[    1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2
[    1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd
response 0x900, card status 0x0
[    1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3

This patches fixes this by adding the missing driver type setting.

Fixes: bb8175a8aa42 ("mmc: sdhci: clarify DDR timing mode ...")
Signed-off-by: Jisheng Zhang 
Signed-off-by: Ulf Hansson 
Signed-off-by: Luis Henriques