Pull MMC updates from Ulf Hansson: "MMC core: - Reject invalid perdev_minors for the block device before division - Document DT fixed-layout NVMEM provider support for eMMC cards MMC host: - Convert a couple of plain text DT bindings to the yaml format - bcm2835: DMA mapping improvements - cqhci: Fix sparse warnings for endian conversions - dw_mmc: Stop and complete DMA also in busy state - dw_mmc-rockchip: Add support for the RV1106 variant - litex_mmc: Add dynamic bus width support - moxart: Propagate error for DMA completion timeout - pxamci: Remove PXA remnants for the PXA93x support - rtsx_usb_sdmmc: Avoid USB I/O in runtime autosuspend - rtsx_usb_sdmmc: Suppress false CD after init timeout - sdhci_am654: Add Judith Mendez as maintainer - sdhci-esdhc-mcf: Do not use readl()/writel() on ColdFire - sdhci-msm: Extend the DT bindings for ICE - sdhci-tegra: Add support for Tegra264/Tegra238 variants - sunxi: Add support for the Allwinner A733 variant - via-sdmmc: Clean up card detect work at remove and in probe error path" * tag 'mmc-v7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (35 commits) ARM: PXA: Fix build error for PXA93x dt-bindings: mmc: sunxi: add compatible string for Allwinner A733 MMC0/1/2 dt-bindings: mmc: Document fixed-layout NVMEM provider support mmc: sdhci-tegra: Add Tegra264 SoC data dt-bindings: mmc: tegra: Document Tegra264 SDHCI mmc: sdhci-tegra: Add Tegra238 SoC data dt-bindings: mmc: tegra: Document Tegra238 SDHCI mmc: omap_hsmmc: use platform_get_irq_optional for wake IRQ mmc: via-sdmmc: cancel card-detect work on remove mmc: via-sdmmc: stop card-detect handling on probe failure mmc: moxart: use platform helpers for resource and IRQ mmc: host: Remove redundant dev_err()/dev_err_probe() mmc: bcm2835: DMA mapping improvements mmc: dw_mmc: move declaration of dw_mci_pmops dt-bindings: mmc: rockchip-dw-mshc: Add RV1106 compatible mmc: rtsx_usb_sdmmc: suppress false CD after init timeout misc: rtsx_usb: avoid USB I/O in runtime autosuspend mmc: sdhci-of-dwcmshc: Log eMMC reset calls mmc: block: reject invalid perdev_minors before division mmc: sdhci-of-ma35d1: add missing MODULE_DEVICE_TABLE() ...
Pull networking updates from Jakub Kicinski:
"One of the 'small improvements all over the place' releases for us.
It's hard to draw any direct comparisons because summer vacations
disrupted our patch processing (and presumably - generation) quite a
bit.
Quick and dirty count suggests we (Paolo and I) merged a very similar
number of net (632) and net-next (648) patches. This is not telling
the full story either because 1/3 to 1/2 of the net-next patches also
*seem* like AI-driven low priority fixes, cleanups and clarifications.
We are completely overwhelmed, of course. The glimmer of hope is that
we secured sufficient LLM budget and access (thank you Meta!) to run
reviews with multiple frontier models on each patch. This eliminates
some hallucinations. That said, in terms of review, the LLMs can only
do so much.
The sad truth is that our APIs (especially for rare events like PCIe
errors, timeouts etc) have always been racy, and now LLMs don't let us
ignore that. I expect our direction for the next release will be to
tweak the reviews a little bit more, but start shifting focus to
letting the LLMs take care of the busy work - managing patchwork,
automating common process complaints, editing commit messages, and
maybe applying patches which already got "reviewed-by" tags from
people we trust...
Core & protocols:
- A few steps lowering rtnl_lock dependence:
- per-netns netdev unregistration for select SW drivers (e.g.
veth, ipvlan, tunnels)
- rtnl_lock-less FIB rule changes (RTM_NEWRULE and RTM_DELRULE)
- prepare software drivers and TC qdiscs for rtnl_lock-less GET
- Support BIG TCP (>64kB TSO) in UDP tunnels (vxlan, geneve)
- Support buffers larger than PAGE_SIZE in devmem zero-copy API
- Improve MPTCP handling of extreme memory pressure handling, when
out-of-order queue had to be pruned
- Report the per-group user count via RTM_GETMULTICAST
- Expose the route deletion reason in RTM_DELROUTE
- Add a SO_RIGHTS_NOTRUNC option to UNIX sockets to enable more
useful handling of LSM denials when receiving SCM_RIGHTS messages:
instead of truncating the message at the first blocked fd, keep
every fd slot and store the LSM errno in the blocked slot
- IPv6 Segment Routing - support looking up the post-encap SID
(address) in a different/specified routing table
- Support PRP RedBox (interlink) creation
- Support per-nexthop UDP dst port in VXLAN
- Continue converting getsockopt callbacks in a number of protocols
to iov_iter
Ethernet:
- Merge initial CXL support for AMD/Solarflare NICs (shared branch
with the CXL tree)
- New drivers:
- ADIN1140 10BASE-T1S MACPHY
- Initial skeleton of Intel iXD and ZTE Dinghai drivers
- High-speed NICs:
- AMD/Pensando:
- support firmware flashing
- Cisco (enic):
- SR-IOV V2 admin channel and MBOX protocol
- Huawei (hns3):
- support for ethtool pfc_prevention_tout
- nVidia/Mellanox:
- support sharing bandwidth control across interfaces
of the same device
- Marvell (octeontx2-pf):
- link RQ page pools to netdev for Netlink stats
- Google vNIC:
- XDP metadata support for DQ RDA
- Microsoft vNIC:
- support forcing full-page RX buffers
- Other NICs:
- Synopsys IP:
- eic7700: support for eth1
- Microchip (lan743x):
- support for RMII interface
- Wangxun:
- support for ethtool -G and -C for VFs
- add Tx timeout and PCIe error handling
- Intel (igb/igc):
- RSS key get/set support
- support for forcing link speed without auto-negotiation
- Switches:
- NXP (dpaa2):
- support bonding/LAG offload
- Mediatek:
- mt7530: EN7528 support
- initial support for MT7628
- Micrel (ksz8/9):
- refactoring work to move towards library model
- PTP support for KSZ8463
- nVidia/Mellanox:
- support rtnl-lock-less ethtool callbacks
- Realtek:
- rtl8366rb: use generic RTL83xx code
- support SGMII and HSGMII for RTL8367S
- PHYs:
- Airoha:
- EcoNet EN7528 PHY support
- DAPU Telecom
- DAPU Telecom DAP8211R(I) Gigabit PHY support
- Realtek:
- support RTL8261C_CG
- support RTL8261D
Wireless:
- nl80211: per-link statistics support for multi-link operation
- mac80211: AQL/airtime-fairness support for multicast
- Merge Peripheral Authentication Service (PAS) / TEE support for
ath12k (shared branch with the firmware/qcom tree)
- New drivers:
- mm81x for Morse Micro Long-Range S1G devices
- nxpwifi for NXP devices (mostly forked off from mwifiex)
- Driver changes:
- Broadcom (brcmfmac):
- DPP support, some Cypress part update
- MediaTek (mt76):
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- Qualcomm (ath12k):
- much kernel infrastructure integration work
- AHB platform MultiPD support
- Realtek (rt89):
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- Intel:
- new FW version support
Bluetooth:
- HCI: add support for Shorter Connection Interval (SCI) feature
- af_bluetooth: add minimal context analysis annotations
- Driver changes:
- Intel:
- add Bluetooth SAR revision 2 support
- add vendor_reset PCI sysfs for PLDR
- Mediatek:
- add USB IDs for MT7902 and MT7922 devices
- Realtek:
- add USB IDs for 8761CU and 8852BE devices
- NXP:
- add M.2 Bluetooth device support using pwrseq
Misc:
- DPLL support for manual/numerical oscillator control (NCO)
(implement in zl3073x)
- MCTP support for MCTP over USB v1.1 (DMTF DSP0283)
- Power-over-Ethernet: support Realtek PSE controllers
- Remove the IBM EHEA driver
- Remove tulip/xircom_cb driver"
* tag 'net-next-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1433 commits)
net/mlx5e: do not HW-GRO coalesce small frames
net: openvswitch: fix nf_connlabels leak in ovs_ct_init
net: add missing ref_tracker_dir_exit() to alloc_netdev_mqs()
net: openvswitch: fix flow mask use-after-free on flow deletion
sctp: stop processing a packet once its association is deleted
dpll: zl3073x: add PTP clock support
dpll: zl3073x: add channel ToD, phase step and TIE operations
dpll: zl3073x: scale poll interval proportionally to timeout
ptp: vmclock: prevent read-only mappings from becoming writable
ipv4: reject undersized MTUs in ip_do_fragment()
bonding: initialize err for empty target lists
net: dsa: initial support for MT7628 embedded switch
net: dsa: initial MT7628 tagging driver
net: phy: mediatek: add phy driver for MT7628 built-in Fast Ethernet PHYs
dt-bindings: net: dsa: add MT7628 ESW
net: pse-pd: realtek-pse-mcu: add UART transport
net: pse-pd: realtek-pse-mcu: add I2C transport
net: pse-pd: add Realtek PSE MCU core
dt-bindings: net: pse-pd: add bindings for Realtek PSE MCU
vsock: use sock_error() to consume sk_err after a failed connect
...
Merge the mmc fixes for v7.2-rc[n] into the next branch, to allow them to get tested together with the mmc changes that are targeted for the next release. Signed-off-by: Ulf Hansson <ulfh@kernel.org>
In ls2k0500_mmc_reorder_cmd_data() and ls2k2000_mmc_reorder_cmd_data(),
the for_each_sg() macro already iterates over the scatterlist entries,
with 'sg' pointing to the current entry. However, the code incorrectly
uses '&sg[i]' and 'sg_dma_len(&sg[i])' inside the loop, which treats
'sg' as an array base and indexes it again, leading to access of
wrong sg entries (or out-of-bounds if the list is not an array).
Cc: stable@vger.kernel.org
Fixes: d0f8e961deae ("mmc: loongson2: Add Loongson-2K2000 SD/SDIO/eMMC controller driver")
Fixes: 2115772014bd ("mmc: loongson2: Add Loongson-2K SD/SDIO controller driver")
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
omap_hsmmc_prepare_data() converts the command busy timeout to nanoseconds
with:
timeout = req->cmd->busy_timeout * NSEC_PER_MSEC;
busy_timeout is an unsigned int (milliseconds) and timeout is a u64, but
NSEC_PER_MSEC is 1000000L. On 32-bit builds the multiplication is
performed in 32-bit arithmetic and wraps for busy_timeout values above
~4294 ms, before the result is assigned to the u64.
The driver does not set mmc->max_busy_timeout, so the core does not cap the
busy timeout, and commands such as erase or SANITIZE (MMC_SANITIZE_TIMEOUT_MS
is 240000 ms) can pass a busy_timeout far larger than 4294 ms. The wrapped,
much smaller ns value is then programmed via set_data_timeout(), so the data
timeout is set too short and the operation can time out prematurely.
Cast busy_timeout to u64 before the multiplication so the conversion is done
in 64-bit arithmetic.
Fixes: 8cc9a3e73de1 ("mmc: host: omap_hsmmc: use generic_cmd6_time to program timeout value for CMD6")
Cc: stable@vger.kernel.org
Signed-off-by: Zhan Xusheng <zhanxusheng@xiaomi.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
In atmci_probe, &host->bh_work is bound with atmci_work_func, and
atmci_interrupt, atmci_timeout_timer and atmci_dma_complete can all
queue this work on system_bh_wq.
If we remove the module, atmci_remove makes cleanup and the memory
allocated for host with devm_kzalloc() is released after the remove
callback returns, while the work mentioned above may still be pending
or running. The sequence of operations that may lead to a UAF bug is
as follows:
CPU0 CPU1
| atmci_interrupt
| queue_work(system_bh_wq,
| &host->bh_work)
atmci_remove |
atmci_cleanup_slot(...) |
atmci_writel(host, ATMCI_IDR, ~0UL) |
timer_delete_sync(&host->timer) |
dma_release_channel(host->dma.chan) |
free_irq(platform_get_irq(pdev, 0), host) |
| atmci_work_func
| // use host
// devm resources released after |
// remove returns, host is freed |
| // use host (use-after-free)
Fix it by canceling the work after all the sources that can schedule
it (IRQ handler, timeout timer and DMA completion callback) have been
stopped, and before proceeding with the remaining cleanup in
atmci_remove.
Fixes: 7d2be0749a59 ("atmel-mci: Driver for Atmel on-chip MMC controllers")
Assisted-by: Codex:deepseek-v4-flash
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
sdhci_allocate_bounce_buffer() allocates its buffer with devm_kmalloc()
but maps it with dma_map_single(). The buffer is therefore released by
devres without the streaming DMA mapping being unmapped.
Register a managed action after dma_map_single() succeeds so the mapping
is removed before devres releases the buffer. The action is registered
only for buffers allocated and mapped by the SDHCI core, leaving buffers
provided by host drivers under their existing ownership.
Fixes: bd9b902798ab ("mmc: sdhci: Implement an SDHCI-specific bounce buffer")
Cc: stable@vger.kernel.org
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Coverity report INTEGER_OVERFLOW for host->tuning_err.
The tuning_err field in struct sdhci_host is used to store an error
code for re-tuning, but it was declared as unsigned int. Several call
sites store negative error codes into it and later compare against
negative values:
- sdhci.c, sdhci-of-dwcmshc.c and sdhci-pci-gli.c assign it the
return value of __sdhci_execute_tuning()/__sdhci_execute_tuning_9750(),
both of which return a signed int (possibly a negative errno);
- sdhci-of-esdhc.c assigns host->tuning_err = -EAGAIN and later does
"ret = host->tuning_err; if (ret == -EAGAIN ...)";
- sdhci-of-dwcmshc.c prints it with the %d (signed) conversion.
Storing a negative errno in an unsigned int and reading it back as a
signed int only happens to work because of two's-complement, same-width
integer conversions. It is misleading and triggers sign-conversion
warnings. All users treat the value either as a signed error code or as
a boolean (zero / non-zero), so changing the type to a signed int is
safe and makes the intent explicit.
Fixes: 7d8bb1f46e13 ("mmc: sdhci: add tuning error codes")
Assisted-by: Cline:claude-sonnet [read_file, search_files, git]
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Add a new SoC data structure for Tegra264 platforms and register the nvidia,tegra264-sdhci compatible string. Configure the supported features and tap delay values for the Tegra264 SDHCI controller. Signed-off-by: Prathamesh Shete <pshete@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Add a new SoC data structure for Tegra238 platforms and register the nvidia,tegra238-sdhci compatible string. Configure the supported features and tap delay values for the Tegra238 SDHCI controller. Signed-off-by: Prathamesh Shete <pshete@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Ulf Hansson <ulfh@kernel.org>