linux-stable.git/drivers/mmc, branch linux-rolling-stable

mmc: sdhci-esdhc-imx: fix resume error handling

2026-07-24T14:21:24+00:00

commit e27c946b589c53520409a0956b33d52ef7a0898f upstream.

Check pm_runtime_force_resume() return value in resume. If it fails
(clock enable failure), return immediately since accessing hardware
registers on an unclocked device would cause a kernel panic.

The early return intentionally skips enable_irq() and
sdhci_disable_irq_wakeups() because the IRQ handler reads
SDHCI_INT_STATUS, which would also fault without clocks. The PM runtime
usage counter leak only affects this already-broken device instance and
is an acceptable tradeoff to preserve system stability.

Remove the return value check for mmc_gpio_set_cd_wake(host->mmc, false)
since disable_irq_wake() called internally always returns 0.

Also return 0 explicitly on the success path instead of propagating
stale return values.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter 
Reviewed-by: Frank Li 
Signed-off-by: Luke Wang 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: make non-fatal errors non-blocking in suspend

2026-07-24T14:21:24+00:00

commit 6aa00a43bbd3d994558a55586351757cebbff236 upstream.

Make pinctrl_pm_select_sleep_state() and mmc_gpio_set_cd_wake() failures
non-fatal in the suspend path. These failures only mean slightly higher
power consumption or missing CD wakeup capability, but should not block
system suspend.

Also change the function to always return 0 on the success path instead
of propagating non-fatal warning return values.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter 
Signed-off-by: Luke Wang 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: use pm_runtime_resume_and_get() in suspend

2026-07-24T14:21:24+00:00

commit 8da5930144712412d85e7f868693d96ec5c2018c upstream.

Replace pm_runtime_get_sync() with pm_runtime_resume_and_get() to
simplify error handling. pm_runtime_resume_and_get() automatically
drops the usage counter on failure, avoiding the need for a separate
pm_runtime_put_noidle() call. If it fails, the device is unclocked and
accessing hardware registers would cause a kernel panic, so return the
error immediately.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter 
Signed-off-by: Luke Wang 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: disable irq during suspend to fix unhandled interrupt

2026-07-24T14:21:24+00:00

commit 9d87eaf985cef9581b6ed99b461b38e8cd666480 upstream.

When using WIFI out-of-band wakeup, an "irq xxx: nobody cared" warning
occurs. This happens because the usdhc interrupt is not disabled during
system suspend when device_may_wakeup() returns false.

The sequence of events leading to this issue:
1. System enters suspend without disabling usdhc interrupt
(because device_may_wakeup() returns false for usdhc device)
2. WIFI out-of-band wakeup triggers system resume via GPIO interrupt
3. WIFI sends a Card interrupt before usdhc has fully resumed
4. usdhc is still in runtime suspend state and cannot handle the
interrupt properly
5. The unhandled interrupt triggers "nobody cared" warning

Fix this by unconditionally disabling the usdhc interrupt during suspend
and re-enabling it during resume, regardless of the wakeup capability.
This ensures no interrupts are processed during the suspend/resume
transition.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter 
Reviewed-by: Haibo Chen 
Signed-off-by: Luke Wang 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: fix esdhc_change_pinstate() to allow default state restore

2026-07-24T14:21:24+00:00

commit 5adc14cd4b905629d5b9163b3a416dcab24c7ce2 upstream.

esdhc_change_pinstate() checks for pins_100mhz and pins_200mhz at the
top of the function and returns -EINVAL if either is not defined. This
prevents the default case from ever being reached, which means devices
with a sleep pinctrl state but without high-speed pin states (100mhz/
200mhz) can never restore their default pin configuration.

Move the IS_ERR checks for pins_100mhz and pins_200mhz into their
respective switch cases.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter 
Reviewed-by: Frank Li 
Signed-off-by: Luke Wang 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: restore DLL override for DDR modes on resume

2026-07-24T14:21:24+00:00

commit 2439becd91bad6883b135044f85f83a0538b96a6 upstream.

sdhci_esdhc_imx_hwinit() unconditionally clears ESDHC_DLL_CTRL by
writing zero. For SDIO devices that keep power during system suspend
and operate in DDR mode, the card remains in DDR timing while the host
DLL override configuration is lost.

Extract the DLL override setup from esdhc_set_uhs_signaling() into
a helper esdhc_set_dll_override(), and call it on the resume path
when the card kept power and is using a DDR timing mode.

Fixes: 676a83855614 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter 
Reviewed-by: Frank Li 
Reviewed-by: Haibo Chen 
Signed-off-by: Luke Wang 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: remove unnecessary mmc_card_wake_sdio_irq check for tuning save/restore

2026-07-24T14:21:23+00:00

commit 899160e2774d9952e9f2770b38f701ff1906c0b2 upstream.

The tuning save/restore during system PM is conditioned on
mmc_card_wake_sdio_irq(), but this check is unrelated to whether
tuning values need to be preserved. The actual requirement is that
the card keeps power during suspend and the controller is a uSDHC.

SDIO devices using out-of-band GPIO wakeup maintain power during
suspend but do not set the SDIO IRQ wake flag. In this case the
tuning delay values are not saved/restored.

Remove the unnecessary mmc_card_wake_sdio_irq() condition from both
the suspend save and resume restore paths.

Fixes: c63d25cdc59a ("mmc: sdhci-esdhc-imx: Save tuning value when card stays powered in suspend")
Acked-by: Adrian Hunter 
Reviewed-by: Frank Li 
Reviewed-by: Haibo Chen 
Signed-off-by: Luke Wang 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-dwcmshc: check bus clock enable result in the probe() method

2026-07-24T14:21:23+00:00

commit 521f39ca93cc43ce1b3eae8d44201f8f55dd9151 upstream.

In the driver's probe() method, clk_disable_unprepare() for the bus clock
is called on the error path even if the prior clk_prepare_enable() call has
failed (and the same thing happens in the remove() method as well) -- that
would cause the prepare/enable counter imbalance.  Also, the same problem
can happen in the driver's suspend() method; note that the resume() method
does check the clk_prepare_enable()'s result -- let's be consistent and do
that in probe() method as well.  BTW, I don't know for sure what does the
bus clock control -- if it affects the register accesses, the driver will
likely cause (e.g. on ARM) a kernel oops if it fails to prepare/enable the
bus clock in the probe() method...

Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.

Fixes: e438cf49b305 ("mmc: sdhci-of-dwcmshc: add SDHCI OF Synopsys DWC MSHC driver")
Fixes: bccce2ec7790 ("mmc: sdhci-of-dwcmshc: add suspend/resume support")
Signed-off-by: Sergey Shtylyov 
Acked-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: mmc_test: Fix __counted_by handling after kzalloc_flex() conversion

2026-07-24T14:21:23+00:00

commit c35fac6481a1dbb2d114dd337b54a40799437546 upstream.

Fix logic issues introduced by the kzalloc_flex() conversion in
mmc_test_alloc_mem() due to interaction with the __counted_by
annotation on the flexible array.

Bounds-checking sanitizers rely on the counter field reflecting the
allocated array size before any array access occurs. However, use
mem->cnt both as the allocation size and as the runtime insertion
index, causing incorrect indexing and potentially invalid bounds
tracking.

Initialize mem->cnt to the maximum allocated number of segments
immediately after kzalloc_flex(), then use a separate local index
variable to track successfully allocated entries. Update mem->cnt to
the actual number of initialized elements before returning or entering
the cleanup path.

Also rewrite mmc_test_free_mem() to use a forward for-loop, improving
readability and ensuring only initialized entries are freed.

Fixes: c3126dccfd7b ("mmc: mmc_test: use kzalloc_flex")
Signed-off-by: Lad Prabhakar 
Reviewed-by: Geert Uytterhoeven 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: block: fix RPMB device unregister ordering

2026-07-24T14:21:23+00:00

commit 86152fef52cac15cd662ed3bfc7604fbfef378f0 upstream.

Since commit 7852028a35f0 ("mmc: block: register RPMB partition with
the RPMB subsystem"), each mmc RPMB partition is represented by two
device objects:
 - the mmc-owned device (`rpmb->dev`, backing the legacy /dev/mmcblkXrpmb
   char device) and
 - the rpmb-core device (`rdev`, backing /dev/rpmbN).

The child RPMB device holds a reference to its parent, so the
parent's release callback cannot be invoked if the child device
is still registered.

Remove rpmb_dev_unregister() from the parent release handler and
unregister the child RPMB device in the remove path before tearing
down the parent device.

Also delete the extra blank line between mmc_blk_remove_rpmb_part()
and {.

Fixes: 7852028a35f0 ("mmc: block: register RPMB partition with the RPMB subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Jiazi Li 
Signed-off-by: Ao Sun 
Reviewed-by: Avri Altman 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman