linux-stable.git/drivers/mmc/host, branch v5.4.151 Linux kernel stable tree mmc: rtsx_pci: Fix long reads when clock is prescaled 2021-09-22T10:26:34+00:00 Thomas Hebb tommyhebb@gmail.com 2021-08-01T11:46:14+00:00 48f5a5f0276d529450c2b16810cb09e5767d1a2a [ Upstream commit 3ac5e45291f3f0d699a721357380d4593bc2dcb3 ] For unexplained reasons, the prescaler register for this device needs to be cleared (set to 1) while performing a data read or else the command will hang. This does not appear to affect the real clock rate sent out on the bus, so I assume it's purely to work around a hardware bug. During normal operation, the prescaler is already set to 1, so nothing needs to be done. However, in "initial mode" (which is used for sub-MHz clock speeds, like the core sets while enumerating cards), it's set to 128 and so we need to reset it during data reads. We currently fail to do this for long reads. This has no functional affect on the driver's operation currently written, as the MMC core always sets a clock above 1MHz before attempting any long reads. However, the core could conceivably set any clock speed at any time and the driver should still work, so I think this fix is worthwhile. I personally encountered this issue while performing data recovery on an external chip. My connections had poor signal integrity, so I modified the core code to reduce the clock speed. Without this change, I saw the card enumerate but was unable to actually read any data. Writes don't seem to work in the situation described above even with this change (and even if the workaround is extended to encompass data write commands). I was not able to find a way to get them working. Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 3ac5e45291f3f0d699a721357380d4593bc2dcb3 ]

For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.

During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.

This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.

I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.

Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: sdhci-of-arasan: Check return value of non-void funtions 2021-09-22T10:26:34+00:00 Manish Narani manish.narani@xilinx.com 2021-06-15T10:43:54+00:00 4e773c5553b2138206255af2d10034fbe66c35a8 [ Upstream commit 66bad6ed2204fdb78a0a8fb89d824397106a5471 ] At a couple of places, the return values of the non-void functions were not getting checked. This was reported by the coverity tool. Modify the code to check the return values of the same. Addresses-Coverity: ("check_return") Signed-off-by: Manish Narani <manish.narani@xilinx.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 66bad6ed2204fdb78a0a8fb89d824397106a5471 ]

At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.

Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: moxart: Fix issue with uninitialized dma_slave_config 2021-09-15T07:47:36+00:00 Tony Lindgren tony@atomide.com 2021-08-10T08:16:44+00:00 fb8e695e9cfa47864c5df8f1c15c2a4b8cf753f2 [ Upstream commit ee5165354d498e5bceb0b386e480ac84c5f8c28c ] Depending on the DMA driver being used, the struct dma_slave_config may need to be initialized to zero for the unused data. For example, we have three DMA drivers using src_port_window_size and dst_port_window_size. If these are left uninitialized, it can cause DMA failures. For moxart, this is probably not currently an issue but is still good to fix though. Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver") Cc: Jonas Jensen <jonas.jensen@gmail.com> Cc: Vinod Koul <vkoul@kernel.org> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit ee5165354d498e5bceb0b386e480ac84c5f8c28c ]

Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.

For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.

For moxart, this is probably not currently an issue but is still good to
fix though.

Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: dw_mmc: Fix issue with uninitialized dma_slave_config 2021-09-15T07:47:36+00:00 Tony Lindgren tony@atomide.com 2021-08-10T08:16:43+00:00 48b1f117e8d0a049135e178c11beb7c08fcd81c3 [ Upstream commit c3ff0189d3bc9c03845fe37472c140f0fefd0c79 ] Depending on the DMA driver being used, the struct dma_slave_config may need to be initialized to zero for the unused data. For example, we have three DMA drivers using src_port_window_size and dst_port_window_size. If these are left uninitialized, it can cause DMA failures. For dw_mmc, this is probably not currently an issue but is still good to fix though. Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support") Cc: Shawn Lin <shawn.lin@rock-chips.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit c3ff0189d3bc9c03845fe37472c140f0fefd0c79 ]

Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.

For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.

For dw_mmc, this is probably not currently an issue but is still good to
fix though.

Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: sdhci-msm: Update the software timeout value for sdhc 2021-09-03T08:08:12+00:00 Shaik Sajida Bhanu sbhanu@codeaurora.org 2021-07-16T11:46:14+00:00 1cccf5c03077c42fc861202948367e8f70a5a37b [ Upstream commit 67b13f3e221ed81b46a657e2b499bf8b20162476 ] Whenever SDHC run at clock rate 50MHZ or below, the hardware data timeout value will be 21.47secs, which is approx. 22secs and we have a current software timeout value as 10secs. We have to set software timeout value more than the hardware data timeout value to avioid seeing the below register dumps. [ 332.953670] mmc2: Timeout waiting for hardware interrupt. [ 332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 332.966450] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00007202 [ 332.973256] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001 [ 332.980054] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000027 [ 332.986864] mmc2: sdhci: Present: 0x01f801f6 | Host ctl: 0x0000001f [ 332.993671] mmc2: sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 333.000583] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 333.007386] mmc2: sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 333.014182] mmc2: sdhci: Int enab: 0x03ff100b | Sig enab: 0x03ff100b [ 333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000 [ 333.027771] mmc2: sdhci: Caps: 0x322dc8b2 | Caps_1: 0x0000808f [ 333.034561] mmc2: sdhci: Cmd: 0x0000183a | Max curr: 0x00000000 [ 333.041359] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x00000000 [ 333.048157] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 [ 333.054945] mmc2: sdhci: Host ctl2: 0x00000000 [ 333.059657] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000ffffff218 [ 333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP ----------- [ 333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg: 0x6000642c | DLL cfg2: 0x0020a000 [ 333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl: 0x00000000 | DDR cfg: 0x80040873 [ 333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 : 0xf88218a8 Vndr func3: 0x02626040 [ 333.102371] mmc2: sdhci: ============================================ So, set software timeout value more than hardware timeout value. Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1626435974-14462-1-git-send-email-sbhanu@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 67b13f3e221ed81b46a657e2b499bf8b20162476 ]

Whenever SDHC run at clock rate 50MHZ or below, the hardware data
timeout value will be 21.47secs, which is approx. 22secs and we have
a current software timeout value as 10secs. We have to set software
timeout value more than the hardware data timeout value to avioid seeing
the below register dumps.

[  332.953670] mmc2: Timeout waiting for hardware interrupt.
[  332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[  332.966450] mmc2: sdhci: Sys addr:  0x00000000 | Version:  0x00007202
[  332.973256] mmc2: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000001
[  332.980054] mmc2: sdhci: Argument:  0x00000000 | Trn mode: 0x00000027
[  332.986864] mmc2: sdhci: Present:   0x01f801f6 | Host ctl: 0x0000001f
[  332.993671] mmc2: sdhci: Power:     0x00000001 | Blk gap:  0x00000000
[  333.000583] mmc2: sdhci: Wake-up:   0x00000000 | Clock:    0x00000007
[  333.007386] mmc2: sdhci: Timeout:   0x0000000e | Int stat: 0x00000000
[  333.014182] mmc2: sdhci: Int enab:  0x03ff100b | Sig enab: 0x03ff100b
[  333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[  333.027771] mmc2: sdhci: Caps:      0x322dc8b2 | Caps_1:   0x0000808f
[  333.034561] mmc2: sdhci: Cmd:       0x0000183a | Max curr: 0x00000000
[  333.041359] mmc2: sdhci: Resp[0]:   0x00000900 | Resp[1]:  0x00000000
[  333.048157] mmc2: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
[  333.054945] mmc2: sdhci: Host ctl2: 0x00000000
[  333.059657] mmc2: sdhci: ADMA Err:  0x00000000 | ADMA Ptr:
0x0000000ffffff218
[  333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP
-----------
[  333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg:
0x6000642c | DLL cfg2: 0x0020a000
[  333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl:
0x00000000 | DDR cfg: 0x80040873
[  333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 :
0xf88218a8 Vndr func3: 0x02626040
[  333.102371] mmc2: sdhci: ============================================

So, set software timeout value more than hardware timeout value.

Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1626435974-14462-1-git-send-email-sbhanu@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: dw_mmc: Fix hang on data CRC error 2021-08-26T12:36:20+00:00 Vincent Whitchurch vincent.whitchurch@axis.com 2021-06-30T10:22:32+00:00 85e60614d1f60ef1de5bae426174452fbe5c617b [ Upstream commit 25f8203b4be1937c4939bb98623e67dcfd7da4d1 ] When a Data CRC interrupt is received, the driver disables the DMA, then sends the stop/abort command and then waits for Data Transfer Over. However, sometimes, when a data CRC error is received in the middle of a multi-block write transfer, the Data Transfer Over interrupt is never received, and the driver hangs and never completes the request. The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed "before assertion of SWR". Do these operations in the recommended order. With this change the Data Transfer Over is always received correctly in my tests. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 25f8203b4be1937c4939bb98623e67dcfd7da4d1 ]

When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.

However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.

The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR".  Do these operations in the recommended
order.  With this change the Data Transfer Over is always received
correctly in my tests.

Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: sdhci: Fix warning message when accessing RPMB in HS400 mode 2021-07-19T06:53:15+00:00 Al Cooper alcooperx@gmail.com 2021-06-24T16:30:45+00:00 7e3b6e797a4383e6506ebbd0154efad1354c4f30 commit d0244847f9fc5e20df8b7483c8a4717fe0432d38 upstream. When an eMMC device is being run in HS400 mode, any access to the RPMB device will cause the error message "mmc1: Invalid UHS-I mode selected". This happens as a result of tuning being disabled before RPMB access and then re-enabled after the RPMB access is complete. When tuning is re-enabled, the system has to switch from HS400 to HS200 to do the tuning and then back to HS400. As part of sequence to switch from HS400 to HS200 the system is temporarily put into HS mode. When switching to HS mode, sdhci_get_preset_value() is called and does not have support for HS mode and prints the warning message and returns the preset for SDR12. The fix is to add support for MMC and SD HS modes to sdhci_get_preset_value(). This can be reproduced on any system running eMMC in HS400 mode (not HS400ES) by using the "mmc" utility to run the following command: "mmc rpmb read-counter /dev/mmcblk0rpmb". Signed-off-by: Al Cooper <alcooperx@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 52983382c74f ("mmc: sdhci: enhance preset value function") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit d0244847f9fc5e20df8b7483c8a4717fe0432d38 upstream.

When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().

This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".

Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c74f ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: vub3000: fix control-request direction 2021-07-14T14:53:48+00:00 Johan Hovold johan@kernel.org 2021-05-21T13:30:26+00:00 4aaace2dc1ada688d71d16bd5e349499725d4b04 commit 3c0bb3107703d2c58f7a0a7a2060bb57bc120326 upstream. The direction of the pipe argument must match the request-type direction bit or control requests may fail depending on the host-controller-driver implementation. Fix the SET_ROM_WAIT_STATES request which erroneously used usb_rcvctrlpipe(). Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver") Cc: stable@vger.kernel.org # 3.0 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3c0bb3107703d2c58f7a0a7a2060bb57bc120326 upstream.

The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.

Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().

Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org      # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc: usdhi6rol0: fix error return code in usdhi6_probe() 2021-07-14T14:53:22+00:00 Zhen Lei thunder.leizhen@huawei.com 2021-05-08T02:03:21+00:00 ccbcdcd4af98055abc888972fcbcc0ce14c2522c [ Upstream commit 2f9ae69e5267f53e89e296fccee291975a85f0eb ] Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Link: https://lore.kernel.org/r/20210508020321.1677-1-thunder.leizhen@huawei.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 2f9ae69e5267f53e89e296fccee291975a85f0eb ]

Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.

Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210508020321.1677-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: via-sdmmc: add a check against NULL pointer dereference 2021-07-14T14:53:13+00:00 Zheyu Ma zheyuma97@gmail.com 2021-06-03T13:33:20+00:00 31ef30f8f8786b70a27837634ad176a4b035ac27 [ Upstream commit 45c8ddd06c4b729c56a6083ab311bfbd9643f4a6 ] Before referencing 'host->data', the driver needs to check whether it is null pointer, otherwise it will cause a null pointer reference. This log reveals it: [ 29.355199] BUG: kernel NULL pointer dereference, address: 0000000000000014 [ 29.357323] #PF: supervisor write access in kernel mode [ 29.357706] #PF: error_code(0x0002) - not-present page [ 29.358088] PGD 0 P4D 0 [ 29.358280] Oops: 0002 [#1] PREEMPT SMP PTI [ 29.358595] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4- g70e7f0549188-dirty #102 [ 29.359164] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 29.359978] RIP: 0010:via_sdc_isr+0x21f/0x410 [ 29.360314] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00 10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43 18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77 [ 29.361661] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046 [ 29.362042] RAX: 0000000000000000 RBX: ffff888107d77880 RCX: 0000000000000000 [ 29.362564] RDX: 0000000000000000 RSI: ffffffff835d20bb RDI: 00000000ffffffff [ 29.363085] RBP: ffffc90000118ed8 R08: 0000000000000001 R09: 0000000000000001 [ 29.363604] R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000008600 [ 29.364128] R13: ffff888107d779c8 R14: ffffc90009c00200 R15: 0000000000008000 [ 29.364651] FS: 0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000 [ 29.365235] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 29.365655] CR2: 0000000000000014 CR3: 0000000005a2e000 CR4: 00000000000006e0 [ 29.366170] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 29.366683] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 29.367197] Call Trace: [ 29.367381] <IRQ> [ 29.367537] __handle_irq_event_percpu+0x53/0x3e0 [ 29.367916] handle_irq_event_percpu+0x35/0x90 [ 29.368247] handle_irq_event+0x39/0x60 [ 29.368632] handle_fasteoi_irq+0xc2/0x1d0 [ 29.368950] __common_interrupt+0x7f/0x150 [ 29.369254] common_interrupt+0xb4/0xd0 [ 29.369547] </IRQ> [ 29.369708] asm_common_interrupt+0x1e/0x40 [ 29.370016] RIP: 0010:native_safe_halt+0x17/0x20 [ 29.370360] Code: 07 0f 00 2d db 80 43 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 c2 37 e5 01 55 48 89 e5 85 c0 7e 07 0f 00 2d bb 80 43 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d f9 91 [ 29.371696] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246 [ 29.372079] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000 [ 29.372595] RDX: 0000000000000000 RSI: ffffffff854f67a4 RDI: ffffffff85403406 [ 29.373122] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001 [ 29.373646] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86009188 [ 29.374160] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100258000 [ 29.374690] default_idle+0x9/0x10 [ 29.374944] arch_cpu_idle+0xa/0x10 [ 29.375198] default_idle_call+0x6e/0x250 [ 29.375491] do_idle+0x1f0/0x2d0 [ 29.375740] cpu_startup_entry+0x18/0x20 [ 29.376034] start_secondary+0x11f/0x160 [ 29.376328] secondary_startup_64_no_verify+0xb0/0xbb [ 29.376705] Modules linked in: [ 29.376939] Dumping ftrace buffer: [ 29.377187] (ftrace buffer empty) [ 29.377460] CR2: 0000000000000014 [ 29.377712] ---[ end trace 51a473dffb618c47 ]--- [ 29.378056] RIP: 0010:via_sdc_isr+0x21f/0x410 [ 29.378380] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00 10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43 18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77 [ 29.379714] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046 [ 29.380098] RAX: 0000000000000000 RBX: ffff888107d77880 RCX: 0000000000000000 [ 29.380614] RDX: 0000000000000000 RSI: ffffffff835d20bb RDI: 00000000ffffffff [ 29.381134] RBP: ffffc90000118ed8 R08: 0000000000000001 R09: 0000000000000001 [ 29.381653] R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000008600 [ 29.382176] R13: ffff888107d779c8 R14: ffffc90009c00200 R15: 0000000000008000 [ 29.382697] FS: 0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000 [ 29.383277] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 29.383697] CR2: 0000000000000014 CR3: 0000000005a2e000 CR4: 00000000000006e0 [ 29.384223] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 29.384736] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 29.385260] Kernel panic - not syncing: Fatal exception in interrupt [ 29.385882] Dumping ftrace buffer: [ 29.386135] (ftrace buffer empty) [ 29.386401] Kernel Offset: disabled [ 29.386656] Rebooting in 1 seconds.. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Link: https://lore.kernel.org/r/1622727200-15808-1-git-send-email-zheyuma97@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 45c8ddd06c4b729c56a6083ab311bfbd9643f4a6 ]

Before referencing 'host->data', the driver needs to check whether it is
null pointer, otherwise it will cause a null pointer reference.

This log reveals it:

[   29.355199] BUG: kernel NULL pointer dereference, address:
0000000000000014
[   29.357323] #PF: supervisor write access in kernel mode
[   29.357706] #PF: error_code(0x0002) - not-present page
[   29.358088] PGD 0 P4D 0
[   29.358280] Oops: 0002 [#1] PREEMPT SMP PTI
[   29.358595] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-
g70e7f0549188-dirty #102
[   29.359164] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009),
BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   29.359978] RIP: 0010:via_sdc_isr+0x21f/0x410
[   29.360314] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00
10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43
18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77
[   29.361661] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046
[   29.362042] RAX: 0000000000000000 RBX: ffff888107d77880
RCX: 0000000000000000
[   29.362564] RDX: 0000000000000000 RSI: ffffffff835d20bb
RDI: 00000000ffffffff
[   29.363085] RBP: ffffc90000118ed8 R08: 0000000000000001
R09: 0000000000000001
[   29.363604] R10: 0000000000000000 R11: 0000000000000001
R12: 0000000000008600
[   29.364128] R13: ffff888107d779c8 R14: ffffc90009c00200
R15: 0000000000008000
[   29.364651] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000)
knlGS:0000000000000000
[   29.365235] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   29.365655] CR2: 0000000000000014 CR3: 0000000005a2e000
CR4: 00000000000006e0
[   29.366170] DR0: 0000000000000000 DR1: 0000000000000000
DR2: 0000000000000000
[   29.366683] DR3: 0000000000000000 DR6: 00000000fffe0ff0
DR7: 0000000000000400
[   29.367197] Call Trace:
[   29.367381]  <IRQ>
[   29.367537]  __handle_irq_event_percpu+0x53/0x3e0
[   29.367916]  handle_irq_event_percpu+0x35/0x90
[   29.368247]  handle_irq_event+0x39/0x60
[   29.368632]  handle_fasteoi_irq+0xc2/0x1d0
[   29.368950]  __common_interrupt+0x7f/0x150
[   29.369254]  common_interrupt+0xb4/0xd0
[   29.369547]  </IRQ>
[   29.369708]  asm_common_interrupt+0x1e/0x40
[   29.370016] RIP: 0010:native_safe_halt+0x17/0x20
[   29.370360] Code: 07 0f 00 2d db 80 43 00 f4 5d c3 0f 1f 84 00 00 00
00 00 8b 05 c2 37 e5 01 55 48 89 e5 85 c0 7e 07 0f 00 2d bb 80 43 00 fb
f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d f9 91
[   29.371696] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246
[   29.372079] RAX: 0000000000000000 RBX: 0000000000000002
RCX: 0000000000000000
[   29.372595] RDX: 0000000000000000 RSI: ffffffff854f67a4
RDI: ffffffff85403406
[   29.373122] RBP: ffffc9000008fe90 R08: 0000000000000001
R09: 0000000000000001
[   29.373646] R10: 0000000000000000 R11: 0000000000000001
R12: ffffffff86009188
[   29.374160] R13: 0000000000000000 R14: 0000000000000000
R15: ffff888100258000
[   29.374690]  default_idle+0x9/0x10
[   29.374944]  arch_cpu_idle+0xa/0x10
[   29.375198]  default_idle_call+0x6e/0x250
[   29.375491]  do_idle+0x1f0/0x2d0
[   29.375740]  cpu_startup_entry+0x18/0x20
[   29.376034]  start_secondary+0x11f/0x160
[   29.376328]  secondary_startup_64_no_verify+0xb0/0xbb
[   29.376705] Modules linked in:
[   29.376939] Dumping ftrace buffer:
[   29.377187]    (ftrace buffer empty)
[   29.377460] CR2: 0000000000000014
[   29.377712] ---[ end trace 51a473dffb618c47 ]---
[   29.378056] RIP: 0010:via_sdc_isr+0x21f/0x410
[   29.378380] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00
10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43
18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77
[   29.379714] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046
[   29.380098] RAX: 0000000000000000 RBX: ffff888107d77880
RCX: 0000000000000000
[   29.380614] RDX: 0000000000000000 RSI: ffffffff835d20bb
RDI: 00000000ffffffff
[   29.381134] RBP: ffffc90000118ed8 R08: 0000000000000001
R09: 0000000000000001
[   29.381653] R10: 0000000000000000 R11: 0000000000000001
R12: 0000000000008600
[   29.382176] R13: ffff888107d779c8 R14: ffffc90009c00200
R15: 0000000000008000
[   29.382697] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000)
knlGS:0000000000000000
[   29.383277] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   29.383697] CR2: 0000000000000014 CR3: 0000000005a2e000
CR4: 00000000000006e0
[   29.384223] DR0: 0000000000000000 DR1: 0000000000000000
DR2: 0000000000000000
[   29.384736] DR3: 0000000000000000 DR6: 00000000fffe0ff0
DR7: 0000000000000400
[   29.385260] Kernel panic - not syncing: Fatal exception in interrupt
[   29.385882] Dumping ftrace buffer:
[   29.386135]    (ftrace buffer empty)
[   29.386401] Kernel Offset: disabled
[   29.386656] Rebooting in 1 seconds..

Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/1622727200-15808-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>