linux-stable.git/drivers/mmc/host, branch linux-5.6.y

mmc: uniphier-sd: call devm_request_irq() after tmio_mmc_host_probe()

2020-06-17T14:42:07+00:00

commit 5d1f42e14b135773c0cc1d82e904c5b223783a9d upstream.

Currently, tmio_mmc_irq() handler is registered before the host is
fully initialized by tmio_mmc_host_probe(). I did not previously notice
this problem.

The boot ROM of a new Socionext SoC unmasks interrupts (CTL_IRQ_MASK)
somehow. The handler is invoked before tmio_mmc_host_probe(), then
emits noisy call trace.

Move devm_request_irq() below tmio_mmc_host_probe().

Fixes: 3fd784f745dd ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Masahiro Yamada 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200511062158.1790924-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: tmio: Further fixup runtime PM management at remove

2020-06-17T14:42:07+00:00

commit 4bd784411aca022622e484eb262f5a0540ae732c upstream.

Before calling tmio_mmc_host_probe(), the caller is required to enable
clocks for its device, as to make it accessible when reading/writing
registers during probe.

Therefore, the responsibility to disable these clocks, in the error path of
->probe() and during ->remove(), is better managed outside
tmio_mmc_host_remove(). As a matter of fact, callers of
tmio_mmc_host_remove() already expects this to be the behaviour.

However, there's a problem with tmio_mmc_host_remove() when the Kconfig
option, CONFIG_PM, is set. More precisely, tmio_mmc_host_remove() may then
disable the clock via runtime PM, which leads to clock enable/disable
imbalance problems, when the caller of tmio_mmc_host_remove() also tries to
disable the same clocks.

To solve the problem, let's make sure tmio_mmc_host_remove() leaves the
device with clocks enabled, but also make sure to disable the IRQs, as we
normally do at ->runtime_suspend().

Reported-by: Geert Uytterhoeven 
Reviewed-by: Wolfram Sang 
Tested-by: Wolfram Sang 
Signed-off-by: Ulf Hansson 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200519152434.6867-1-ulf.hansson@linaro.org
Tested-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman

mmc: mmci_sdmmc: fix DMA API warning overlapping mappings

2020-06-17T14:42:07+00:00

commit fe8d33bd33d527dee3155d2bccd714a655f37334 upstream.

Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 20 at kernel/dma/debug.c:500 add_dma_entry+0x16c/0x17c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x031d2645
Modules linked in:
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.5.0-rc2-00021-gdeda30999c2b-dirty #49
Hardware name: STM32 (Device Tree Support)
Workqueue: events_freezable mmc_rescan
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (dump_stack+0xc0/0xd4)
[] (dump_stack) from [] (__warn+0xd0/0xf8)
[] (__warn) from [] (warn_slowpath_fmt+0x94/0xb8)
[] (warn_slowpath_fmt) from [] (add_dma_entry+0x16c/0x17c)
[] (add_dma_entry) from [] (debug_dma_map_sg+0xe4/0x3d4)
[] (debug_dma_map_sg) from [] (sdmmc_idma_prep_data+0x94/0xf8)
[] (sdmmc_idma_prep_data) from [] (mmci_prep_data+0x2c/0xb0)
[] (mmci_prep_data) from [] (mmci_start_data+0x134/0x2f0)
[] (mmci_start_data) from [] (mmci_request+0xe8/0x154)
[] (mmci_request) from [] (mmc_start_request+0x94/0xbc)

DMA api debug brings to light leaking dma-mappings, dma_map_sg and
dma_unmap_sg are not correctly balanced.

If a request is prepared, the dma_map/unmap are done in asynchronous call
pre_req (prep_data) and post_req (unprep_data). In this case the
dma-mapping is right balanced.

But if the request was not prepared, the data->host_cookie is define to
zero and the dma_map/unmap must be done in the request.  The dma_map is
called by mmci_dma_start (prep_data), but there is no dma_unmap in this
case.

This patch adds dma_unmap_sg when the dma is finalized and the data cookie
is zero (request not prepared).

Signed-off-by: Ludovic Barre 
Link: https://lore.kernel.org/r/20200526155103.12514-2-ludovic.barre@st.com
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-at91: fix CALCR register being rewritten

2020-06-17T14:42:07+00:00

commit dbdea70f71d672c12bc4454e7c258a8f78194d74 upstream.

When enabling calibration at reset, the CALCR register was completely
rewritten. This may cause certain bits being deleted unintentedly.
Fix by issuing a read-modify-write operation.

Fixes: 727d836a375a ("mmc: sdhci-of-at91: add DT property to enable calibration on full reset")
Signed-off-by: Eugen Hristev 
Link: https://lore.kernel.org/r/20200527105659.142560-1-eugen.hristev@microchip.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-msm: Clear tuning done flag while hs400 tuning

2020-06-17T14:42:07+00:00

commit 9253d71011c349d5f5cc0cebdf68b4a80811b92d upstream.

Clear tuning_done flag while executing tuning to ensure vendor
specific HS400 settings are applied properly when the controller
is re-initialized in HS400 mode.

Without this, re-initialization of the qcom SDHC in HS400 mode fails
while resuming the driver from runtime-suspend or system-suspend.

Fixes: ff06ce417828 ("mmc: sdhci-msm: Add HS400 platform support")
Cc: stable@vger.kernel.org
Signed-off-by: Veerabhadrarao Badiganti 
Link: https://lore.kernel.org/r/1590678838-18099-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-pci-gli: Fix can not access GL9750 after reboot from Windows 10

2020-05-20T06:22:15+00:00

[ Upstream commit b56ff195c317ad28c05d354aeecbb9995b8e08c1 ]

Need to clear some bits in a vendor-defined register after reboot from
Windows 10.

Fixes: e51df6ce668a ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Reported-by: Grzegorz Kowal 
Signed-off-by: Ben Chuang 
Acked-by: Adrian Hunter 
Tested-by: Grzegorz Kowal 
Link: https://lore.kernel.org/r/20200504063957.6638-1-benchuanggli@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: alcor: Fix a resource leak in the error path for ->probe()

2020-05-20T06:22:15+00:00

[ Upstream commit 7c277dd2b0ff6a16f1732a66c2c52a29f067163e ]

If devm_request_threaded_irq() fails, the allocated struct mmc_host needs
to be freed via calling mmc_free_host(), so let's do that.

Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Signed-off-by: Christophe JAILLET 
Link: https://lore.kernel.org/r/20200426202355.43055-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: sdhci-pci-gli: Fix no irq handler from suspend

2020-05-20T06:22:11+00:00

[ Upstream commit 282ede76e47048eebc8ce5324b412890f0ec0a69 ]

The kernel prints a message similar to
"[   28.881959] do_IRQ: 5.36 No irq handler for vector"
when GL975x resumes from suspend. Implement a resume callback to fix this.

Fixes: 31e43f31890c ("mmc: sdhci-pci-gli: Enable MSI interrupt for GL975x")
Co-developed-by: Renius Chen 
Signed-off-by: Renius Chen 
Tested-by: Dave Flogeras 
Signed-off-by: Ben Chuang 
Tested-by: Vineeth Pillai 
Acked-by: Adrian Hunter 
Link: https://lore.kernel.org/r/20200427103048.20785-1-benchuanggli@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Zou 
[Samuel Zou: Make sdhci_pci_gli_resume() static]
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: sdhci-acpi: Add SDHCI_QUIRK2_BROKEN_64_BIT_DMA for AMDI0040

2020-05-20T06:22:00+00:00

[ Upstream commit 45a3fe3bf93b7cfeddc28ef7386555e05dc57f06 ]

The AMD eMMC 5.0 controller does not support 64 bit DMA.

Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel 
Link: https://marc.info/?l=linux-mmc&m=158879884514552&w=2
Reviewed-by: Andy Shevchenko 
Acked-by: Adrian Hunter 
Link: https://lore.kernel.org/r/20200508165344.1.Id5bb8b1ae7ea576f26f9d91c761df7ccffbf58c5@changeid
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin

mmc: meson-mx-sdio: remove the broken ->card_busy() op

2020-05-06T06:16:30+00:00

commit ddca1092c4324c89cf692b5efe655aa251864b51 upstream.

The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".

It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.

Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.

Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman