linux-stable.git/drivers/mmc/core, branch v4.7.2

mmc: fix mmc mode selection for HS-DDR and higher

2016-06-02T08:39:05+00:00

When IS_ERR_VALUE was removed from the mmc core code, it was replaced
with a simple not-zero check. This does not work, as the value checked
is the return value for mmc_select_bus_width, which returns the set
bit width on success. This made eMMC modes higher than HS-DDR unusable.

Fix this by checking for a positive return value instead.

Fixes: 287980e49ffc ("remove lots of IS_ERR_VALUE abuses")
Cc: Arnd Bergmann 
Signed-off-by: Chen-Yu Tsai 
Acked-by: Hans de Goede 
Reviewed-by: Krzysztof Kozlowski 
Acked-by: Jaehoon Chung 
Reviewed-by: Shawn Lin 
Tested-by: Marcel Ziswiler 
Tested-by: Bjorn Andersson 
Signed-off-by: Ulf Hansson

remove lots of IS_ERR_VALUE abuses

2016-05-27T22:26:11+00:00

Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.

However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.

Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.

This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.

Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.

I was using this definition for testing:

 #define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
       unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))

which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.

I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.

[ Updated the 9p parts as per Al Viro  - Linus ]

Signed-off-by: Arnd Bergmann 
Cc: Andrzej Hajda 
Cc: Andrew Morton 
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla  # For nvmem part
Signed-off-by: Linus Torvalds

mmc: longer timeout for long read time quirk

2016-05-23T09:52:40+00:00

008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.

This patch will...

() Increase the long read time quirk timeout from 300ms to 600ms. Original
   author of that quirk says 300ms was only a guess and that the number
   may need to be raised in the future.

() Add this specific MMC to the quirk

Signed-off-by: Matt Gumbel 
Signed-off-by: Adrian Hunter 
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson

mmc: core: Add a facility to "pause" re-tuning

2016-05-17T14:54:26+00:00

Re-tuning is not possible when switched to the RPMB
partition.  However re-tuning should not be needed
if re-tuning is done immediately before switching,
a small set of operations is done, and then we
immediately switch back to the main partition.

To ensure that re-tuning can't be done for a short
while, add a facility to "pause" re-tuning.

The existing facility to hold / release re-tuning
is used but it also flags re-tuning as needed to cause
re-tuning before the next command (which will be the
switch to RPMB).

We also need to "unpause" in the recovery path, which
is catered for by adding it to mmc_retune_disable().

Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson

mmc: mmc: Fix partition switch timeout for some eMMCs

2016-05-16T09:31:28+00:00

Some eMMCs set the partition switch timeout too low.

Now typically eMMCs are considered a critical component (e.g. because
they store the root file system) and consequently are expected to be
reliable.  Thus we can neglect the use case where eMMCs can't switch
reliably and we might want a lower timeout to facilitate speedy
recovery.

Although we could employ a quirk for the cards that are affected (if
we could identify them all), as described above, there is little
benefit to having a low timeout, so instead simply set a minimum
timeout.

The minimum is set to 300ms somewhat arbitrarily - the examples that
have been seen had a timeout of 10ms but were sometimes taking 60-70ms.

Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson

mmc: sdio: fall back to SDIO 1.0 for broken 1.1 cards

2016-05-16T09:31:27+00:00

I have two SDIO WLAN cards which specify being SDIO Rev. 1.1 cards but
their FUNCE tuple reports the smaller size of a Rev 1.0 card. So,
enforce 1.0 on these cards to avoid reading the not present registers.
They are not really used anyhow. My cards initialize properly after this
patch.

Signed-off-by: Wolfram Sang 
Signed-off-by: Ulf Hansson

mmc: core: remove the invalid message in mmc_select_timing

2016-05-10T08:37:59+00:00

mmc_select_hs200() and mmc_select_hs() will keep the timing
as before if switch fails. So it's meaningless to print the
failed switched mode outside based on the current host timing.

Furthermore, the original print is wrong, it should be:
pr_warn("%s: switch to %s failed\n",
	mmc_hostname(card->host),
	mmc_card_hs(card) ? "high-speed" :
	(mmc_card_hs200(card) ? "hs200" : ""));

Since we already have error message in mmc_select_hs200(),
simply remove it outside.

Signed-off-by: Dong Aisheng 
Signed-off-by: Ulf Hansson

mmc: core: fix using wrong io voltage if mmc_select_hs200 fails

2016-05-10T08:37:01+00:00

Currently MMC core will keep going if HS200/HS timing switch failed
with -EBADMSG error by the assumption that the old timing is still valid.

However, for mmc_select_hs200 case, the signal voltage may have already
been switched. If the timing switch failed, we should fall back to
the old voltage in case the card is continue run with legacy timing.

If fall back signal voltage failed, we explicitly report an EIO error
to force retry during the next power cycle.

Signed-off-by: Dong Aisheng 
Signed-off-by: Ulf Hansson

mmc: mmc: Attempt to flush cache before reset

2016-05-04T11:11:53+00:00

CMD0 or hardware reset may invalidate the cache, so it needs to be
flushed before reset.

In the case of recovery, we can't expect flushing the cache to work
always, but have a go and ignore errors.

Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson

mmc: core: Convert from IDR to IDA for host indexes

2016-05-02T08:33:36+00:00

As IDA is more lightweight than IDR, let's convert to use that instead.

Signed-off-by: Ulf Hansson