linux-stable.git/drivers/mmc/core, branch v3.9.2

mmc: core: Fix bit width test failing on old eMMC cards

2013-05-08T03:33:15+00:00

commit 836dc2fe89c968c10cada87e0dfae6626f8f9da3 upstream.

PARTITION_SUPPORT needs to be set before doing the compare on version
number so the bit width test does not get invalid data.  Before this
patch, a Sandisk iNAND eMMC card would detect 1-bit width although
the hardware supports 4-bit.

Only affects old emmc devices - pre 4.4 devices.

Reported-by: Elad Yi 
Signed-off-by: Philip Rakity 
Signed-off-by: Chris Ball 
Signed-off-by: Greg Kroah-Hartman

mmc: convert to idr_alloc()

2013-02-28T03:10:17+00:00

Convert to the much saner new idr interface.

Signed-off-by: Tejun Heo 
Cc: Chris Ball 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

2013-02-26T17:31:09+00:00

Pull MMC update from Chris Ball:
"MMC highlights for 3.9:

Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.

Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"

* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...

mmc: add DT bindings for more MMC capability flags

2013-02-24T19:37:25+00:00

Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.

Signed-off-by: Guennadi Liakhovetski 
Signed-off-by: Chris Ball

mmc: provide a standard MMC device-tree binding parser centrally

2013-02-24T19:37:19+00:00

MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().

Signed-off-by: Guennadi Liakhovetski 
Signed-off-by: Chris Ball

mmc: support packed write command for eMMC4.5 devices

2013-02-24T19:37:16+00:00

This patch supports packed write command of eMMC4.5 devices.  Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally.  As a result, packed command help
write throughput be improved.  The following tables show the results
of packed write.

Type A:
test     none |  packed
iozone   25.8 |  31
tiotest  27.6 |  31.2
lmdd     31.2 |  35.4

Type B:
test     none |  packed
iozone   44.1 |  51.1
tiotest  47.9 |  52.5
lmdd     51.6 |  59.2

Type C:
test     none |  packed
iozone   19.5 |  32
tiotest  19.9 |  34.5
lmdd     22.8 |  40.7

Signed-off-by: Seungwon Jeon 
Reviewed-by: Maya Erez 
Reviewed-by: Namjae Jeon 
Signed-off-by: Chris Ball

mmc: add packed command feature of eMMC4.5

2013-02-24T19:37:15+00:00

This patch adds packed command feature of eMMC4.5.  The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.

Signed-off-by: Seungwon Jeon 
Reviewed-by: Maya Erez 
Reviewed-by: Subhash Jadavani 
Reviewed-by: Namjae Jeon 
Signed-off-by: Chris Ball

mmc: use regulator_can_change_voltage() instead of regulator_count_voltages

2013-02-24T19:37:14+00:00

mmc_regulator_set_ocr() depends on the ability of regulator to change the
voltage value. When regulator cannot change its voltage output, some code
is skipped to avoid reporting false errors on some boards, which use MMC
hosts with fixed regulators (e.g. Samsung Goni and UniversalC210 boards).

This patch replaces a hacky workaround based on regulator_count_voltages()
value with the correct call to recently introduced
regulator_can_change_voltage() function in regulators core.

Signed-off-by: Marek Szyprowski 
Signed-off-by: Chris Ball

mmc: core: fix indentation

2013-02-24T19:37:13+00:00

This patch fixes incorrect indentation.  (Just code cleanup)

Signed-off-by: Jaehoon Chung 
Signed-off-by: Chris Ball

mmc: core: fix permanent sleep of mmcqd during card removal

2013-02-24T19:37:12+00:00

This patch is derived from:
"mmc: fix async request mechanism for sequential read scenarios".

According as async transfer, a request is handled with twice mmc_start_req.
When the card is removed, the request is actually not issued in the first
mmc_start_req [__mmc_start_data_req]. And then mmc_wait_for_data_req_done
will come in the next mmc_start_req. But there is no event for completions.
wake_up_interruptible is needed in __mmc_start_data_req for the case of
removed card.

Signed-off-by: Seungwon Jeon 
Acked-by: Jaehoon Chung 
Tested-by: Konstantin Dorfman 
Signed-off-by: Chris Ball