Since commit 89168b489915 ("mmc: core: restore detect line inversion
semantics"), the SD card on i.MX28 (and possibly other) devices isn't
detected and booting stops at:

[    4.120617] Waiting for root device /dev/mmcblk0p3...

This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly
when the host controller doesn't use a GPIO for card detection (but
instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will
return before assigning to the gpio_invert variable, leaving the
variable uninitialized. The variable then gets used to set the flag.
This patch fixes the issue by making sure gpio_invert is set to false
when a GPIO isn't used. After this patch, i.MX28 boots fine.

The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly
for the exact same reason (it uses the same uninitialized variable), so
this patch fixes that too.

Fixes: 89168b489915 ("mmc: core: restore detect line inversion semantics")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Fix SDIO IRQ bug
   - MMC regulator improvements
   - Fix slot-gpio card detect bug
   - Add support for Driver Stage Register
   - Convert the common MMC OF parser to use GPIO descriptors
   - Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk()
   - Some additional minor fixes

  MMC host:
   - mmci: Support Qualcomm specific DML layer for DMA
   - dw_mmc: Use common MMC regulators
   - dw_mmc: Add support for Rock-chips RK3288
   - tmio: Enable runtime PM support
   - tmio: Add support for R-Car Gen2 SoCs
   - tmio: Several fixes and improvements
   - omap_hsmmc: Removed Balaji from MAINTAINERS
   - jz4740: add DMA and pre/post support
   - sdhci: Add support for Intel Braswell
   - sdhci: Several fixes and improvements"

* tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc: (119 commits)
  ARM: dts: fix MMC2 regulators for Exynos5420 Arndale Octa board
  mmc: sdhci-acpi: Fix Braswell eMMC timeout clock frequency
  mmc: sdhci-acpi: Pass HID and UID to probe_slot
  mmc: sdhci-acpi: Get UID directly from acpi_device
  mmc, sdhci, bcm-kona, LLVMLinux: Remove use of __initconst
  mmc: sdhci-pci: Fix Braswell eMMC timeout clock frequency
  mmc: sdhci: Let a driver override timeout clock frequency
  mmc: sdhci-pci: Add Bay Trail and Braswell SD card detect
  mmc: sdhci-pci: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers
  mmc: sdhci-acpi: Add a HID and UID for a SD Card host controller
  mmc: sdhci-acpi: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers
  mmc: sdhci: Add quirk for always getting TC with stop cmd
  mmc: core: restore detect line inversion semantics
  mmc: Fix incorrect warning when setting 0 Hz via debugfs
  mmc: Fix use of wrong device in mmc_gpiod_free_cd()
  mmc: atmel-mci: fix mismatched section on atmci_cleanup_slot
  mmc: rtsx_pci: Set power related cap2 macros
  mmc: core: Add new power_mode MMC_POWER_UNDEFINED
  mmc: sdhci: execute tuning when device is not busy
  mmc: atmel-mci: Release mmc resources on failure in probe
  ..

commit 98e90de99a0c43bd434da814c882c4332441871e
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.

It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.

Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The commit 46420dd73b80 (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.

Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.

Fixes: 46420dd73b80 (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

It is possible to turn off the card clock by setting
the frequency to zero via debugfs e.g.

	echo 0 > /sys/kernel/debug/mmc0/clock

However that produces an incorrect warning that is
designed to warn if the frequency is below the minimum
operating frequency.  So correct the warning.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc_gpiod_free_cd() is paired with mmc_gpiod_request_cd()
and both must reference the same device which is the
actual host controller device not the mmc_host class
device.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.

For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).

Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use the much more common pr_warn instead of pr_warning.

Other miscellanea:

o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.

Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.

Many host controller probe()s are roughly structured as:

*_probe() {
    host = sdhci_pltfm_init();
    mmc_of_parse(host->mmc);
    rc = sdhci_add_host(host);
    if (rc) {
        sdhci_pltfm_free();
        return rc;
    }

In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().

Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().

sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.

This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():

WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18

The object being complained about is host->detect.

There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().

However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.

This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.

The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.

CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>