commit 9c72a18e46ebe0f09484cce8ebf847abdab58498 upstream.

In raid5, there are scenarios where some ios are deferred to a later
time, and some IO need a flush to complete. To make sure we make
progress with these IOs, we need to call the following functions:

    flush_deferred_bios(conf);
    r5l_flush_stripe_to_raid(conf->log);

Both of these functions are called in raid5d(), but missing in
raid5_do_work(). As a result, these functions are not called
when multi-threading (group_thread_cnt > 0) is enabled. This patch
adds calls to these function to raid5_do_work().

Note for stable branches:

  r5l_flush_stripe_to_raid(conf->log) is need for 4.4+
  flush_deferred_bios(conf) is only needed for 4.11+

Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 208410b546207cfc4c832635fa46419cfa86b4cd upstream.

Data allocated from mempool doesn't always get initialized, this happens when
the data is reused instead of fresh allocation. In the raid1/10 case, we must
reinitialize the bios.

Reported-by: Jonathan G. Underwood <jonathan.underwood@gmail.com>
Fixes: f0250618361d(md: raid10: don't use bio's vec table to manage resync pages)
Fixes: 98d30c5812c3(md: raid1: don't use bio's vec table to manage resync pages)
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When using the block layer in single queue mode, get_request()
returns ERR_PTR(-EAGAIN) if the queue is dying and the REQ_NOWAIT
flag has been passed to get_request(). Avoid that the kernel
reports soft lockup complaints in this case due to continuous
requeuing activity.

Fixes: 7083abbbf ("dm mpath: avoid that path removal can trigger an infinite loop")
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Using the same rate limiting state for different kinds of messages
is wrong because this can cause a high frequency message to suppress
a report of a low frequency message. Hence use a unique rate limiting
state per message type.

Fixes: 71a16736a15e ("dm: use local printk ratelimit")
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Retry requests instead of failing them if an out-of-memory error occurs
or the block driver below dm-mpath is busy.  This restores the v4.12
behavior of noretry_error(), namely that -ENOMEM results in a retry.

Fixes: 2a842acab109 ("block: introduce new block status code type")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Detected by sparse.

Fixes: 4e4cbee93d56 ("block: switch bios to blk_status_t")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

->safemode should be triggered by mdadm for external metadaa array, otherwise
array's state confuses mdadm.

Fixes: 33182d15c6bf(md: always clear ->safemode when md_check_recovery gets the mddev lock.)
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

In r5l_log_endio(), once log->io_list_lock is released, the io unit
may be accessed (or even freed) by other threads. Current code
doesn't handle the io_unit properly, which leads to potential race
conditions.

This patch solves this race condition by:

1. Add a pending_stripe count flush_payload. Multiple flush_payloads
   are counted as only one pending_stripe. Flag has_flush_payload is
   added to show whether the io unit has flush_payload;
2. In r5l_log_endio(), check flags has_null_flush and
   has_flush_payload with log->io_list_lock held. After the lock
   is released, this IO unit is only accessed when we know the
   pending_stripe counter cannot be zeroed by other threads.

Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>

In r5c_journal_mode_set(), it is necessary to call mddev_lock()
before accessing conf and conf->log. Otherwise, the conf->log
may change (and become NULL).

Shaohua: fix unlock in failure cases

Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>

md_write_start() needs to clear the in_sync flag is it is set, or if
there might be a race with set_in_sync() such that the later will
set it very soon.  In the later case it is sufficient to take the
spinlock to synchronize with set_in_sync(), and then set the flag
if needed.

The current test is incorrect.
It should be:
  if "flag is set" or "race is possible"

"flag is set" is trivially "mddev->in_sync".
"race is possible" should be tested by "mddev->sync_checkers".

If sync_checkers is 0, then there can be no race.  set_in_sync() will
wait in percpu_ref_switch_to_atomic_sync() for an RCU grace period,
and as md_write_start() holds the rcu_read_lock(), set_in_sync() will
be sure ot see the update to writes_pending.

If sync_checkers is > 0, there could be race.  If md_write_start()
happened entirely between
		if (!mddev->in_sync &&
		    percpu_ref_is_zero(&mddev->writes_pending)) {
and
			mddev->in_sync = 1;
in set_in_sync(), then it would not see that is_sync had been set,
and set_in_sync() would not see that writes_pending had been
incremented.

This bug means that in_sync is sometimes not set when it should be.
Consequently there is a small chance that the array will be marked as
"clean" when in fact it is inconsistent.

Fixes: 4ad23a976413 ("MD: use per-cpu counter for writes_pending")
cc: stable@vger.kernel.org (v4.12+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>