linux-stable.git/drivers/md/raid1.c, branch v5.3.17

md: improve handling of bio with REQ_PREFLUSH in md_flush_request()

2019-12-17T19:07:47+00:00

commit 775d78319f1ceb32be8eb3b1202ccdc60e9cb7f1 upstream.

If pers->make_request fails in md_flush_request(), the bio is lost. To
fix this, pass back a bool to indicate if the original make_request call
should continue to handle the I/O and instead of assuming the flush logic
will push it to completion.

Convert md_flush_request to return a bool and no longer calls the raid
driver's make_request function.  If the return is true, then the md flush
logic has or will complete the bio and the md make_request call is done.
If false, then the md make_request function needs to keep processing like
it is a normal bio. Let the original call to md_handle_request handle any
need to retry sending the bio to the raid driver's make_request function
should it be needed.

Also mark md_flush_request and the make_request function pointer as
__must_check to issue warnings should these critical return values be
ignored.

Fixes: 2bc13b83e629 ("md: batch flush requests.")
Cc: stable@vger.kernel.org # # v4.19+
Cc: NeilBrown 
Signed-off-by: David Jeffery 
Reviewed-by: Xiao Ni 
Signed-off-by: Song Liu 
Signed-off-by: Greg Kroah-Hartman

md/raid1: fail run raid1 array when active disk less than one

2019-10-05T13:12:03+00:00

[ Upstream commit 07f1a6850c5d5a65c917c3165692b5179ac4cb6b ]

When run test case:
  mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] --assume-clean --bitmap=internal
  mdadm -S /dev/md1
  mdadm -A /dev/md1 /dev/sd[b-c] --run --force

  mdadm --zero /dev/sda
  mdadm /dev/md1 -a /dev/sda

  echo offline > /sys/block/sdc/device/state
  echo offline > /sys/block/sdb/device/state
  sleep 5
  mdadm -S /dev/md1

  echo running > /sys/block/sdb/device/state
  echo running > /sys/block/sdc/device/state
  mdadm -A /dev/md1 /dev/sd[a-c] --run --force

mdadm run fail with kernel message as follow:
[  172.986064] md: kicking non-fresh sdb from array!
[  173.004210] md: kicking non-fresh sdc from array!
[  173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[  173.022406] md1: failed to create bitmap (-5)

In fact, when active disk in raid1 array less than one, we
need to return fail in raid1_run().

Reviewed-by: NeilBrown 
Signed-off-by: Yufen Yu 
Signed-off-by: Song Liu 
Signed-off-by: Sasha Levin

md/raid1: end bio when the device faulty

2019-10-05T13:11:35+00:00

[ Upstream commit eeba6809d8d58908b5ed1b5ceb5fcb09a98a7cad ]

When write bio return error, it would be added to conf->retry_list
and wait for raid1d thread to retry write and acknowledge badblocks.

In narrow_write_error(), the error bio will be split in the unit of
badblock shift (such as one sector) and raid1d thread issues them
one by one. Until all of the splited bio has finished, raid1d thread
can go on processing other things, which is time consuming.

But, there is a scene for error handling that is not necessary.
When the device has been set faulty, flush_bio_list() may end
bios in pending_bio_list with error status. Since these bios
has not been issued to the device actually, error handlding to
retry write and acknowledge badblocks make no sense.

Even without that scene, when the device is faulty, badblocks info
can not be written out to the device. Thus, we also no need to
handle the error IO.

Signed-off-by: Yufen Yu 
Signed-off-by: Song Liu 
Signed-off-by: Sasha Levin

md/raid1: Fix a warning message in remove_wb()

2019-06-26T19:18:48+00:00

The WARN_ON() macro doesn't take an error message, it just takes a
condition.  I've changed this to use WARN(1, "...") instead.

Fixes: 3e148a320979 ("md/raid1: fix potential data inconsistency issue with write behind device")
Signed-off-by: Dan Carpenter 
Signed-off-by: Song Liu

md/raid1: fix potential data inconsistency issue with write behind device

2019-06-20T23:35:59+00:00

For write-behind mode, we think write IO is complete once it has
reached all the non-writemostly devices. It works fine for single
queue devices.

But for multiqueue device, if there are lots of IOs come from upper
layer, then the write-behind device could issue those IOs to different
queues, depends on the each queue's delay, so there is no guarantee
that those IOs can arrive in order.

To address the issue, we need to check the collision among write
behind IOs, we can only continue without collision, otherwise wait
for the completion of previous collisioned IO.

And WBCollision is introduced for multiqueue device which is worked
under write-behind mode.

But this patch doesn't handle below cases which could have the data
inconsistency issue as well, these cases will be handled in later
patches.

1. modify max_write_behind by write backlog node.
2. add or remove array's bitmap dynamically.
3. the change of member disk.

Reviewed-by: NeilBrown 
Signed-off-by: Guoqing Jiang 
Signed-off-by: Song Liu

md: raid1-10: Unify r{1,10}bio_pool_free

2019-06-15T07:37:35+00:00

Avoiding duplicated code, since they just execute a kfree.

Signed-off-by: Marcos Paulo de Souza 
Signed-off-by: Jens Axboe

md/raid1: get rid of extra blank line and space

2019-06-15T07:37:34+00:00

This patch get rid of extra blank line and space, and
add necessary space for code.

Signed-off-by: Yufen Yu 
Signed-off-by: Song Liu 
Signed-off-by: Jens Axboe

drivers: md: Unify common definitions of raid1 and raid10

2019-06-15T07:37:34+00:00

These definitions are being moved to raid1-10.c.

Signed-off-by: Marcos Paulo de Souza 
Signed-off-by: Song Liu 
Signed-off-by: Jens Axboe

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 47

2019-05-24T15:27:13+00:00

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 or at your option any
  later version you should have received a copy of the gnu general
  public license for example usr src linux copying if not write to the
  free software foundation inc 675 mass ave cambridge ma 02139 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 20 file(s).

Signed-off-by: Thomas Gleixner 
Reviewed-by: Allison Randal 
Reviewed-by: Kate Stewart 
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.552543146@linutronix.de
Signed-off-by: Greg Kroah-Hartman

block: remove the i argument to bio_for_each_segment_all

2019-04-30T15:26:13+00:00

We only have two callers that need the integer loop iterator, and they
can easily maintain it themselves.

Suggested-by: Matthew Wilcox 
Reviewed-by: Johannes Thumshirn 
Acked-by: David Sterba 
Reviewed-by: Hannes Reinecke 
Acked-by: Coly Li 
Reviewed-by: Matthew Wilcox 
Signed-off-by: Christoph Hellwig 
Signed-off-by: Jens Axboe