linux-stable.git/drivers/md/raid1.c, branch v4.14.331

md/raid1: fix error: ISO C90 forbids mixed declarations

2023-09-23T08:47:05+00:00

[ Upstream commit df203da47f4428bc286fc99318936416253a321c ]

There is a compile error when this commit is added:
md: raid1: fix potential OOB in raid1_remove_disk()

drivers/md/raid1.c: In function 'raid1_remove_disk':
drivers/md/raid1.c:1844:9: error: ISO C90 forbids mixed declarations
and code [-Werror=declaration-after-statement]
1844 |         struct raid1_info *p = conf->mirrors + number;
     |         ^~~~~~

That's because the new code was inserted before the struct.
The change is move the struct command above this commit.

Fixes: 8b0472b50bcf ("md: raid1: fix potential OOB in raid1_remove_disk()")
Signed-off-by: Nigel Croxon 
Signed-off-by: Song Liu 
Link: https://lore.kernel.org/r/46d929d0-2aab-4cf2-b2bf-338963e8ba5a@redhat.com
Signed-off-by: Sasha Levin

md: raid1: fix potential OOB in raid1_remove_disk()

2023-09-23T08:47:04+00:00

[ Upstream commit 8b0472b50bcf0f19a5119b00a53b63579c8e1e4d ]

If rddev->raid_disk is greater than mddev->raid_disks, there will be
an out-of-bounds in raid1_remove_disk(). We have already found
similar reports as follows:

1) commit d17f744e883b ("md-raid10: fix KASAN warning")
2) commit 1ebc2cec0b7d ("dm raid: fix KASAN warning in raid5_remove_disk")

Fix this bug by checking whether the "number" variable is
valid.

Signed-off-by: Zhang Shurong 
Reviewed-by: Yu Kuai 
Link: https://lore.kernel.org/r/tencent_0D24426FAC6A21B69AC0C03CE4143A508F09@qq.com
Signed-off-by: Song Liu 
Signed-off-by: Sasha Levin

md/raid1: stop mdx_raid1 thread when raid1 array run failed

2023-01-18T08:26:32+00:00

[ Upstream commit b611ad14006e5be2170d9e8e611bf49dff288911 ]

fail run raid1 array when we assemble array with the inactive disk only,
but the mdx_raid1 thread were not stop, Even if the associated resources
have been released. it will caused a NULL dereference when we do poweroff.

This causes the following Oops:
    [  287.587787] BUG: kernel NULL pointer dereference, address: 0000000000000070
    [  287.594762] #PF: supervisor read access in kernel mode
    [  287.599912] #PF: error_code(0x0000) - not-present page
    [  287.605061] PGD 0 P4D 0
    [  287.607612] Oops: 0000 [#1] SMP NOPTI
    [  287.611287] CPU: 3 PID: 5265 Comm: md0_raid1 Tainted: G     U            5.10.146 #0
    [  287.619029] Hardware name: xxxxxxx/To be filled by O.E.M, BIOS 5.19 06/16/2022
    [  287.626775] RIP: 0010:md_check_recovery+0x57/0x500 [md_mod]
    [  287.632357] Code: fe 01 00 00 48 83 bb 10 03 00 00 00 74 08 48 89 ......
    [  287.651118] RSP: 0018:ffffc90000433d78 EFLAGS: 00010202
    [  287.656347] RAX: 0000000000000000 RBX: ffff888105986800 RCX: 0000000000000000
    [  287.663491] RDX: ffffc90000433bb0 RSI: 00000000ffffefff RDI: ffff888105986800
    [  287.670634] RBP: ffffc90000433da0 R08: 0000000000000000 R09: c0000000ffffefff
    [  287.677771] R10: 0000000000000001 R11: ffffc90000433ba8 R12: ffff888105986800
    [  287.684907] R13: 0000000000000000 R14: fffffffffffffe00 R15: ffff888100b6b500
    [  287.692052] FS:  0000000000000000(0000) GS:ffff888277f80000(0000) knlGS:0000000000000000
    [  287.700149] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    [  287.705897] CR2: 0000000000000070 CR3: 000000000320a000 CR4: 0000000000350ee0
    [  287.713033] Call Trace:
    [  287.715498]  raid1d+0x6c/0xbbb [raid1]
    [  287.719256]  ? __schedule+0x1ff/0x760
    [  287.722930]  ? schedule+0x3b/0xb0
    [  287.726260]  ? schedule_timeout+0x1ed/0x290
    [  287.730456]  ? __switch_to+0x11f/0x400
    [  287.734219]  md_thread+0xe9/0x140 [md_mod]
    [  287.738328]  ? md_thread+0xe9/0x140 [md_mod]
    [  287.742601]  ? wait_woken+0x80/0x80
    [  287.746097]  ? md_register_thread+0xe0/0xe0 [md_mod]
    [  287.751064]  kthread+0x11a/0x140
    [  287.754300]  ? kthread_park+0x90/0x90
    [  287.757974]  ret_from_fork+0x1f/0x30

In fact, when raid1 array run fail, we need to do
md_unregister_thread() before raid1_free().

Signed-off-by: Jiang Li 
Signed-off-by: Song Liu 
Signed-off-by: Sasha Levin

md/raid1: properly indicate failure when ending a failed write request

2021-05-22T08:57:21+00:00

commit 2417b9869b81882ab90fd5ed1081a1cb2d4db1dd upstream.

This patch addresses a data corruption bug in raid1 arrays using bitmaps.
Without this fix, the bitmap bits for the failed I/O end up being cleared.

Since we are in the failure leg of raid1_end_write_request, the request
either needs to be retried (R1BIO_WriteError) or failed (R1BIO_Degraded).

Fixes: eeba6809d8d5 ("md/raid1: end bio when the device faulty")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Paul Clements 
Signed-off-by: Song Liu 
Signed-off-by: Greg Kroah-Hartman

md: raid1: check rdev before reference in raid1_sync_request func

2020-01-09T09:17:52+00:00

[ Upstream commit 028288df635f5a9addd48ac4677b720192747944 ]

In raid1_sync_request func, rdev should be checked before reference.

Signed-off-by: Zhiqiang Liu 
Signed-off-by: Song Liu 
Signed-off-by: Sasha Levin

md/raid1: fail run raid1 array when active disk less than one

2019-10-05T10:48:00+00:00

[ Upstream commit 07f1a6850c5d5a65c917c3165692b5179ac4cb6b ]

When run test case:
  mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] --assume-clean --bitmap=internal
  mdadm -S /dev/md1
  mdadm -A /dev/md1 /dev/sd[b-c] --run --force

  mdadm --zero /dev/sda
  mdadm /dev/md1 -a /dev/sda

  echo offline > /sys/block/sdc/device/state
  echo offline > /sys/block/sdb/device/state
  sleep 5
  mdadm -S /dev/md1

  echo running > /sys/block/sdb/device/state
  echo running > /sys/block/sdc/device/state
  mdadm -A /dev/md1 /dev/sd[a-c] --run --force

mdadm run fail with kernel message as follow:
[  172.986064] md: kicking non-fresh sdb from array!
[  173.004210] md: kicking non-fresh sdc from array!
[  173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[  173.022406] md1: failed to create bitmap (-5)

In fact, when active disk in raid1 array less than one, we
need to return fail in raid1_run().

Reviewed-by: NeilBrown 
Signed-off-by: Yufen Yu 
Signed-off-by: Song Liu 
Signed-off-by: Sasha Levin

md/raid1: end bio when the device faulty

2019-10-05T10:47:49+00:00

[ Upstream commit eeba6809d8d58908b5ed1b5ceb5fcb09a98a7cad ]

When write bio return error, it would be added to conf->retry_list
and wait for raid1d thread to retry write and acknowledge badblocks.

In narrow_write_error(), the error bio will be split in the unit of
badblock shift (such as one sector) and raid1d thread issues them
one by one. Until all of the splited bio has finished, raid1d thread
can go on processing other things, which is time consuming.

But, there is a scene for error handling that is not necessary.
When the device has been set faulty, flush_bio_list() may end
bios in pending_bio_list with error status. Since these bios
has not been issued to the device actually, error handlding to
retry write and acknowledge badblocks make no sense.

Even without that scene, when the device is faulty, badblocks info
can not be written out to the device. Thus, we also no need to
handle the error IO.

Signed-off-by: Yufen Yu 
Signed-off-by: Song Liu 
Signed-off-by: Sasha Levin

md/raid1: don't clear bitmap bits on interrupted recovery.

2019-02-20T09:20:54+00:00

commit dfcc34c99f3ebc16b787b118763bf9cb6b1efc7a upstream.

sync_request_write no longer submits writes to a Faulty device. This has
the unfortunate side effect that bitmap bits can be incorrectly cleared
if a recovery is interrupted (previously, end_sync_write would have
prevented this). This means the next recovery may not copy everything
it should, potentially corrupting data.

Add a function for doing the proper md_bitmap_end_sync, called from
end_sync_write and the Faulty case in sync_request_write.

backport note to 4.14: s/md_bitmap_end_sync/bitmap_end_sync
Cc: stable@vger.kernel.org 4.14+
Fixes: 0c9d5b127f69 ("md/raid1: avoid reusing a resync bio after error handling.")
Reviewed-by: Jack Wang 
Tested-by: Jack Wang 
Signed-off-by: Nate Dailey 
Signed-off-by: Song Liu 
Signed-off-by: Greg Kroah-Hartman

MD: fix invalid stored role for a disk - try2

2018-11-13T19:15:18+00:00

commit 9e753ba9b9b405e3902d9f08aec5f2ea58a0c317 upstream.

Commit d595567dc4f0 (MD: fix invalid stored role for a disk) broke linear
hotadd. Let's only fix the role for disks in raid1/10.
Based on Guoqing's original patch.

Reported-by: kernel test robot 
Cc: Gioh Kim 
Cc: Guoqing Jiang 
Signed-off-by: Shaohua Li 
Signed-off-by: Greg Kroah-Hartman

md/raid1: add error handling of read error from FailFast device

2018-08-03T05:50:33+00:00

[ Upstream commit b33d10624fdc15cdf1495f3f00481afccec76783 ]

Current handle_read_error() function calls fix_read_error()
only if md device is RW and rdev does not include FailFast flag.
It does not handle a read error from a RW device including
FailFast flag.

I am not sure it is intended. But I found that write IO error
sets rdev faulty. The md module should handle the read IO error and
write IO error equally. So I think read IO error should set rdev faulty.

Signed-off-by: Gioh Kim 
Reviewed-by: Jack Wang 
Signed-off-by: Shaohua Li 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman