linux-stable.git/drivers/leds/Makefile, branch linux-4.9.y Linux kernel stable tree leds: add driver for Mellanox systems LEDs 2016-09-15T14:49:39+00:00 Vadim Pasternak vadimp@mellanox.com 2016-09-08T07:25:53+00:00 be4fdf99fa4dc95aa01144b207caf2cc9fa074d8 This makes it possible to create a set of LEDs for Mellanox systems: "msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740", "msn2100". Driver obtains LED devices according to system configuration, provided through system DMI data, like mlxcpld:fan1:green, mlxcpld:fan1:red and creates devices in form: "devicename:colour:function". LED setting is controlled through on board CPLD Lattice device. For setting particular LED off, solid, blink: echo 0 > /sys/class/leds/mlxcpld\:status\:green/brightness echo 1 > /sys/class/leds/mlxcpld\:status\:green/brightness echo timer > /sys/class/leds/mlxcpld\:status\:green/trigger On module probing all LEDs are set green, on removing - off. Last setting overwrites previous, f.e. sequence for changing LED from green - red - green: echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness echo 1 > /sys/class/leds/mlxcpld\:psu\:red/brightness echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness Note: LEDs cannot be turned on/off simultaneously. The Kconfig currently controlling compilation of this code is: drivers/leds/Kconfig:config LEDS_MLXCPLD Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> 
This makes it possible to create a set of LEDs for Mellanox systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100".

Driver obtains LED devices according to system configuration, provided
through system DMI data, like mlxcpld:fan1:green, mlxcpld:fan1:red and
creates devices in form: "devicename:colour:function".

LED setting is controlled through on board CPLD Lattice device.
For setting particular LED off, solid, blink:
echo 0 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo timer > /sys/class/leds/mlxcpld\:status\:green/trigger

On module probing all LEDs are set green, on removing - off.

Last setting overwrites previous, f.e. sequence for
changing LED from green - red - green:
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:red/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
Note: LEDs cannot be turned on/off simultaneously.

The Kconfig currently controlling compilation of this code is:
drivers/leds/Kconfig:config LEDS_MLXCPLD

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
leds: add PM8058 LEDs driver 2016-08-16T20:37:26+00:00 Linus Walleij linus.walleij@linaro.org 2016-08-16T09:25:10+00:00 7f866986e7052197396d8a663fa009209af18aee This adds a driver for the six PM8058 LEDs, three ordinary LEDs, two "flash" LEDs and one "keypad" LED. The "keypad" and "flash" LEDs are not really hard-wired to these usecases: for example on the APQ8060 Dragonboard, the "keypad" LED is instead used to drive an IR LED used for the proximity sensor. The "flash" LEDs are just ordinary high-current LED drivers. Cc: linux-arm-msm@vger.kernel.org Cc: Andy Gross <andy.gross@linaro.org> Cc: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> 
This adds a driver for the six PM8058 LEDs, three ordinary LEDs,
two "flash" LEDs and one "keypad" LED.

The "keypad" and "flash" LEDs are not really hard-wired to these
usecases: for example on the APQ8060 Dragonboard, the "keypad"
LED is instead used to drive an IR LED used for the proximity
sensor. The "flash" LEDs are just ordinary high-current LED
drivers.

Cc: linux-arm-msm@vger.kernel.org
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
leds: is31fl319x: 1/3/6/9-channel light effect led driver 2016-08-15T12:02:31+00:00 H. Nikolaus Schaller hns@goldelico.com 2016-07-19T11:47:30+00:00 8c40b7d09ec17c7c01a6db2e16a52dca57b68e36 This is a driver for the Integrated Silicon Solution Inc. LED driver chips series IS31FL319x. They can drive 1, 3, 6 or up to 9 LEDs. Each LED is individually controllable in brightness (through pwm) in 256 steps so that RGB LEDs can show any of ca. 16 Mio colors. The maximum current of the LEDs can be programmed and limited to 5 .. 40mA through a device tree property. The chip is connected through I2C and can have one of 4 addresses in the range 0x64 .. 0x67 depending on how the AD pin is connected. The address is defined by the reg property as usual. The chip also has a shutdown input which could be connected to a GPIO, but this driver uses software shutdown if all LEDs are inactivated. The chip also has breathing and audio features which are not fully supported by this driver. Tested-on: OMAP5 based Pyra handheld prototype. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> 
This is a driver for the Integrated Silicon Solution Inc. LED driver
chips series IS31FL319x. They can drive 1, 3, 6  or up to 9
LEDs.

Each LED is individually controllable in brightness (through pwm)
in 256 steps so that RGB LEDs can show any of ca. 16 Mio colors.

The maximum current of the LEDs can be programmed and limited to
5 .. 40mA through a device tree property.

The chip is connected through I2C and can have one of 4 addresses
in the range 0x64 .. 0x67 depending on how the AD pin is connected. The
address is defined by the reg property as usual.

The chip also has a shutdown input which could be connected to a GPIO,
but this driver uses software shutdown if all LEDs are inactivated.

The chip also has breathing and audio features which are not fully
supported by this driver.

Tested-on: OMAP5 based Pyra handheld prototype.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
leds: LED driver for TI LP3952 6-Channel Color LED 2016-07-18T06:46:09+00:00 Tony Makkiel tony.makkiel@daqri.com 2016-07-11T10:48:49+00:00 d966c943e4dbb66e3afd9f300501c9f3b1c802fd The chip can drive 2 sets of RGB leds. Controller can be controlled via PWM, I2C and audio synchronisation. This driver uses I2C to communicate with the chip. Datasheet: http://www.ti.com/lit/gpn/lp3952 Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> 
The chip can drive 2 sets of RGB leds. Controller can
be controlled via PWM, I2C and audio synchronisation.
This driver uses I2C to communicate with the chip.

Datasheet: http://www.ti.com/lit/gpn/lp3952

Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
leds: Add driver for the ISSI IS31FL32xx family of LED controllers 2016-03-14T08:22:21+00:00 David Rivshin drivshin@allworx.com 2016-03-08T00:57:15+00:00 9d7cffaf99f5f7756746a328c2854ebe4ce9f442 The IS31FL32xx family of LED controllers are I2C devices with multiple constant-current channels, each with independent 256-level PWM control. Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml This has been tested on the IS31FL3236 and IS31FL3216, on an ARM (TI am335x) platform. The programming paradigm of these devices is similar in the following ways: - All registers are 8 bit - All LED control registers are write-only - Each LED channel has a PWM register (0-255) - PWM register writes are shadowed until an Update register is poked - All have a concept of Software Shutdown, which disables output However, there are some differences in devices: - 3236/3235 have a separate Control register for each LED, (3218/3216 pack the enable bits into fewer registers) - 3236/3235 have a per-channel current divisor setting - 3236/3235 have a Global Control register that can turn off all LEDs - 3216 is unique in a number of ways - OUT9-OUT16 can be configured as GPIOs instead of LED controls - LEDs can be programmed with an 8-frame animation, with programmable delay between frames - LEDs can be modulated by an input audio signal - Max output current can be adjusted from 1/4 to 2x globally - Has a Configuration register instead of a Shutdown register This driver currently only supports the base PWM control function of these devices. The following features of these devices are not implemented, although it should be possible to add them in the future: - All devices are capable of going into a lower-power "software shutdown" mode. - The is31fl3236 and is31fl3235 can reduce the max output current per-channel with a divisor of 1, 2, 3, or 4. - The is31fl3216 can use some LED channels as GPIOs instead. - The is31fl3216 can animate LEDs in hardware. - The is31fl3216 can modulate LEDs according to an audio input. - The is31fl3216 can reduce/increase max output current globally. Signed-off-by: David Rivshin <drivshin@allworx.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> 
The IS31FL32xx family of LED controllers are I2C devices with multiple
constant-current channels, each with independent 256-level PWM control.

Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml

This has been tested on the IS31FL3236 and IS31FL3216, on an ARM
(TI am335x) platform.

The programming paradigm of these devices is similar in the following
ways:
 - All registers are 8 bit
 - All LED control registers are write-only
 - Each LED channel has a PWM register (0-255)
 - PWM register writes are shadowed until an Update register is poked
 - All have a concept of Software Shutdown, which disables output

However, there are some differences in devices:
 - 3236/3235 have a separate Control register for each LED,
   (3218/3216 pack the enable bits into fewer registers)
 - 3236/3235 have a per-channel current divisor setting
 - 3236/3235 have a Global Control register that can turn off all LEDs
 - 3216 is unique in a number of ways
    - OUT9-OUT16 can be configured as GPIOs instead of LED controls
    - LEDs can be programmed with an 8-frame animation, with
      programmable delay between frames
    - LEDs can be modulated by an input audio signal
    - Max output current can be adjusted from 1/4 to 2x globally
    - Has a Configuration register instead of a Shutdown register

This driver currently only supports the base PWM control function
of these devices. The following features of these devices are not
implemented, although it should be possible to add them in the future:
 - All devices are capable of going into a lower-power "software
   shutdown" mode.
 - The is31fl3236 and is31fl3235 can reduce the max output current
   per-channel with a divisor of 1, 2, 3, or 4.
 - The is31fl3216 can use some LED channels as GPIOs instead.
 - The is31fl3216 can animate LEDs in hardware.
 - The is31fl3216 can modulate LEDs according to an audio input.
 - The is31fl3216 can reduce/increase max output current globally.

Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
LED/MIPS: Move SEAD3 LED driver to where it belongs. 2015-11-03T07:59:20+00:00 Ralf Baechle ralf@linux-mips.org 2015-08-03T15:04:01+00:00 22a16873d38829570677871a22cf77f00445206f Fixes the following randconfig problem leds-sead3.c:(.text+0x7dc): undefined reference to `led_classdev_unregister' leds-sead3.c:(.text+0x7e8): undefined reference to `led_classdev_unregister' Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: Bryan Wu <cooloney@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-leds@vger.kernel.org Cc: linux-mips@linux-mips.org Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> 
Fixes the following randconfig problem

leds-sead3.c:(.text+0x7dc): undefined reference to `led_classdev_unregister'
leds-sead3.c:(.text+0x7e8): undefined reference to `led_classdev_unregister'

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-leds@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Merge tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight 2015-09-04T18:40:40+00:00 Linus Torvalds torvalds@linux-foundation.org 2015-09-04T18:40:40+00:00 670c039deeffb5c0a3a900de53b95dba781aaf89 Pull backlight updates from Lee Jones: - Stop using LP855X Platform Data to control regulators - Move PWM8941 WLED driver into Backlight - Remove invalid use of IS_ERR_VALUE() macro - Remove duplicate check for NULL data before unregistering - Export I2C Device ID structure * tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: backlight: tosa: Export I2C module alias information backlight: lp8788_bl: Delete a check before backlight_device_unregister() backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro backlight: pm8941-wled: Move PM8941 WLED driver to backlight backlight: lp855x: Use private data for regulator control 
Pull backlight updates from Lee Jones:
 - Stop using LP855X Platform Data to control regulators
 - Move PWM8941 WLED driver into Backlight
 - Remove invalid use of IS_ERR_VALUE() macro
 - Remove duplicate check for NULL data before unregistering
 - Export I2C Device ID structure

* tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: tosa: Export I2C module alias information
  backlight: lp8788_bl: Delete a check before backlight_device_unregister()
  backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro
  backlight: pm8941-wled: Move PM8941 WLED driver to backlight
  backlight: lp855x: Use private data for regulator control
backlight: pm8941-wled: Move PM8941 WLED driver to backlight 2015-08-25T07:41:56+00:00 Bjorn Andersson bjorn.andersson@sonymobile.com 2015-07-22T00:44:49+00:00 7ddbc2423c3301280b883bbb04b998203f30312c The Qualcomm PM8941 WLED block is used for backlight and should therefor be in the backlight framework and not in the LED framework. This moves the driver and adapts to the backlight api instead. Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Tested-by: Rob Clark <robdclark@gmail.com> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Acked-by: Jingoo Han <jingoohan1@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> 
The Qualcomm PM8941 WLED block is used for backlight and should therefor
be in the backlight framework and not in the LED framework. This moves
the driver and adapts to the backlight api instead.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
leds/powernv: Add driver for PowerNV platform 2015-08-20T08:19:07+00:00 Vasant Hegde hegdevasant@linux.vnet.ibm.com 2015-08-19T16:49:54+00:00 84ad6e5cd3e8b365c893f31787864cae5500610b This patch implements LED driver for PowerNV platform using the existing generic LED class framework. PowerNV platform has below type of LEDs: - System attention Indicates there is a problem with the system that needs attention. - Identify Helps the user locate/identify a particular FRU or resource in the system. - Fault Indicates there is a problem with the FRU or resource at the location with which the indicator is associated. We register classdev structures for all individual LEDs detected on the system through LED specific device tree nodes. Device tree nodes specify what all kind of LEDs present on the same location code. It registers LED classdev structure for each of them. All the system LEDs can be found in the same regular path /sys/class/leds/. We don't use LED colors. We use LED node and led-types property to form LED classdev. Our LEDs have names in this format. <location_code>:<attention|identify|fault> Any positive brightness value would turn on the LED and a zero value would turn off the LED. The driver will return LED_FULL (255) for any turned on LED and LED_OFF (0) for any turned off LED. The platform level implementation of LED get and set state has been achieved through OPAL calls. These calls are made available for the driver by exporting from architecture specific codes. Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com> Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com> Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com> Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> 
This patch implements LED driver for PowerNV platform using the existing
generic LED class framework.

PowerNV platform has below type of LEDs:
  - System attention
      Indicates there is a problem with the system that needs attention.
  - Identify
      Helps the user locate/identify a particular FRU or resource in the
      system.
  - Fault
      Indicates there is a problem with the FRU or resource at the
      location with which the indicator is associated.

We register classdev structures for all individual LEDs detected on the
system through LED specific device tree nodes. Device tree nodes specify
what all kind of LEDs present on the same location code. It registers
LED classdev structure for each of them.

All the system LEDs can be found in the same regular path /sys/class/leds/.
We don't use LED colors. We use LED node and led-types property to form
LED classdev. Our LEDs have names in this format.

        <location_code>:<attention|identify|fault>

Any positive brightness value would turn on the LED and a zero value would
turn off the LED. The driver will return LED_FULL (255) for any turned on
LED and LED_OFF (0) for any turned off LED.

The platform level implementation of LED get and set state has been
achieved through OPAL calls. These calls are made available for the
driver by exporting from architecture specific codes.

Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
leds: add BCM6358 LED driver 2015-05-25T20:26:48+00:00 Álvaro Fernández Rojas noltari@gmail.com 2015-05-21T17:11:10+00:00 589fca16c14adec7ebeb601e22850826e18b8f8d This adds support for the LED controller on Broadcom's BCM6358. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Bryan Wu <cooloney@gmail.com> 
This adds support for the LED controller on Broadcom's BCM6358.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>