linux-stable.git/drivers/input, branch v6.5.9

Input: goodix - ensure int GPIO is in input for gpio_count == 1 && gpio_int_idx == 0 case

2023-10-19T21:11:06+00:00

commit 423622a90abb243944d1517b9f57db53729e45c4 upstream.

Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().

It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.

This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.

This part was already fixed in commit 3de93e6ed2df ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.

But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:

[    9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[    9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[    9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[    9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[    9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[    9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[    9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5

Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).

Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.

Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.

Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: xpad - add HyperX Clutch Gladiate Support

2023-10-19T21:11:06+00:00

commit e28a0974d749e5105d77233c0a84d35c37da047e upstream.

Add HyperX controller support to xpad_device and xpad_table.

Suggested-by: Chris Toledanes 
Reviewed-by: Carl Ng 
Signed-off-by: Max Nguyen 
Reviewed-by: Rahul Rameshbabu 
Link: https://lore.kernel.org/r/20230906231514.4291-1-hphyperxdev@gmail.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: i8042 - add Fujitsu Lifebook E5411 to i8042 quirk table

2023-10-19T21:11:06+00:00

commit 80f39e1c27ba9e5a1ea7e68e21c569c9d8e46062 upstream.

In the initial boot stage the integrated keyboard of Fujitsu Lifebook E5411
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.

i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:308A) not working at all.

Since the integrated touchpad is managed by the i2c_designware input
driver in the Linux kernel and you can't find a PS/2 mouse port on the
computer I think it's safe to not use the PS/2 mouse port at all.

Signed-off-by: Szilard Fabian 
Link: https://lore.kernel.org/r/20231004011749.101789-1-szfabian@bluemarch.art
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: xpad - add PXN V900 support

2023-10-19T21:11:06+00:00

commit a65cd7ef5a864bdbbe037267c327786b7759d4c6 upstream.

Add VID and PID to the xpad_device table to allow driver to use the PXN
V900 steering wheel, which is XTYPE_XBOX360 compatible in xinput mode.

Signed-off-by: Matthias Berndt 
Link: https://lore.kernel.org/r/4932699.31r3eYUQgx@fedora
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: psmouse - fix fast_reconnect function for PS/2 mode

2023-10-19T21:11:06+00:00

commit e2cb5cc822b6c9ee72c56ce1d81671b22c05406a upstream.

When the SMBus connection is attempted psmouse_smbus_init() sets
the fast_reconnect pointer to psmouse_smbus_reconnecti(). If SMBus
initialization fails, elantech_setup_ps2() and synaptics_init_ps2() will
fallback to PS/2 mode, replacing the psmouse private data. This can cause
issues on resume, since psmouse_smbus_reconnect() expects to find an
instance of struct psmouse_smbus_dev in psmouse->private.

The issue was uncovered when in 92e24e0e57f7 ("Input: psmouse - add
delay when deactivating for SMBus mode") psmouse_smbus_reconnect()
started attempting to use more of the data structure. The commit was
since reverted, not because it was at fault, but because there was found
a better way of doing what it was attempting to do.

Fix the problem by resetting the fast_reconnect pointer in psmouse
structure in elantech_setup_ps2() and synaptics_init_ps2() when the PS/2
mode is used.

Reported-by: Thorsten Leemhuis 
Tested-by: Thorsten Leemhuis 
Signed-off-by: Jeffery Miller 
Fixes: bf232e460a35 ("Input: psmouse-smbus - allow to control psmouse_deactivate")
Link: https://lore.kernel.org/r/20231005002249.554877-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: powermate - fix use-after-free in powermate_config_complete

2023-10-19T21:11:05+00:00

commit 5c15c60e7be615f05a45cd905093a54b11f461bc upstream.

syzbot has found a use-after-free bug [1] in the powermate driver. This
happens when the device is disconnected, which leads to a memory free from
the powermate_device struct.  When an asynchronous control message
completes after the kfree and its callback is invoked, the lock does not
exist anymore and hence the bug.

Use usb_kill_urb() on pm->config to cancel any in-progress requests upon
device disconnection.

[1] https://syzkaller.appspot.com/bug?extid=0434ac83f907a1dbdd1e

Signed-off-by: Javier Carrasco 
Reported-by: syzbot+0434ac83f907a1dbdd1e@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20230916-topic-powermate_use_after_free-v3-1-64412b81a7a2@gmail.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: tca6416-keypad - fix interrupt enable disbalance

2023-09-19T10:30:14+00:00

[ Upstream commit cc141c35af873c6796e043adcb820833bd8ef8c5 ]

The driver has been switched to use IRQF_NO_AUTOEN, but in the error
unwinding and remove paths calls to enable_irq() were left in place, which
will lead to an incorrect enable counter value.

Fixes: bcd9730a04a1 ("Input: move to use request_irq by IRQF_NO_AUTOEN flag")
Link: https://lore.kernel.org/r/20230724053024.352054-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: tca6416-keypad - always expect proper IRQ number in i2c client

2023-09-19T10:30:14+00:00

[ Upstream commit 687fe7dfb736b03ab820d172ea5dbfc1ec447135 ]

Remove option having i2c client contain raw gpio number instead of proper
IRQ number. There are no users of this facility in mainline and it will
allow cleaning up the driver code with regard to wakeup handling, etc.

Link: https://lore.kernel.org/r/20230724053024.352054-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov 
Stable-dep-of: cc141c35af87 ("Input: tca6416-keypad - fix interrupt enable disbalance")
Signed-off-by: Sasha Levin

Input: iqs7222 - configure power mode before triggering ATI

2023-09-19T10:30:13+00:00

[ Upstream commit 2e00b8bf5624767f6be7427b6eb532524793463e ]

If the device drops into ultra-low-power mode before being placed
into normal-power mode as part of ATI being triggered, the device
does not assert any interrupts until the ATI routine is restarted
two seconds later.

Solve this problem by adopting the vendor's recommendation, which
calls for the device to be placed into normal-power mode prior to
being configured and ATI being triggered.

The original implementation followed this sequence, but the order
was inadvertently changed as part of the resolution of a separate
erratum.

Fixes: 1e4189d8af27 ("Input: iqs7222 - protect volatile registers")
Signed-off-by: Jeff LaBundy 
Link: https://lore.kernel.org/r/ZKrpHc2Ji9qR25r2@nixie71
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: i8042 - add quirk for TUXEDO Gemini 17 Gen1/Clevo PD70PN

2023-09-13T07:52:57+00:00

commit eb09074bdb05ffd6bfe77f8b4a41b76ef78c997b upstream.

The touchpad of this device is both connected via PS/2 and i2c. This causes
strange behavior when both driver fight for control. The easy fix is to
prevent the PS/2 driver from accessing the mouse port as the full feature
set of the touchpad is only supported in the i2c interface anyway.

The strange behavior in this case is, that when an external screen is
connected and the notebook is closed, the pointer on the external screen is
moving to the lower right corner. When the notebook is opened again, this
movement stops, but the touchpad clicks are unresponsive afterwards until
reboot.

Signed-off-by: Werner Sembach 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230607173331.851192-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman