linux-stable.git/drivers/input, branch v4.14.166

Input: add safety guards to input_set_keycode()

2020-01-14T19:05:44+00:00

commit cb222aed03d798fc074be55e59d9a112338ee784 upstream.

If we happen to have a garbage in input device's keycode table with values
too big we'll end up doing clear_bit() with offset way outside of our
bitmaps, damaging other objects within an input device or even outside of
it. Let's add sanity checks to the returned old keycodes.

Reported-by: syzbot+c769968809f9359b07aa@syzkaller.appspotmail.com
Reported-by: syzbot+76f3a30e88d256644c78@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20191207212757.GA245964@dtor-ws
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: atmel_mxt_ts - disable IRQ across suspend

2020-01-04T12:59:35+00:00

[ Upstream commit 463fa44eec2fef50d111ed0199cf593235065c04 ]

Across suspend and resume, we are seeing error messages like the following:

atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)

This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.

Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.

Signed-off-by: Evan Green 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: Fix memory leak in psxpad_spi_probe

2019-12-17T19:38:48+00:00

In the implementation of psxpad_spi_probe() the allocated memory for
pdev is leaked if psxpad_spi_init_ff() or input_register_polled_device()
fail. The solution is using device managed allocation, like the one used
for pad. Perform the allocation using
devm_input_allocate_polled_device().

Fixes: 8be193c7b1f4 ("Input: add support for PlayStation 1/2 joypads connected via SPI")
Signed-off-by: Navid Emamdoost 
Acked-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - add upside-down quirk for Teclast X89 tablet

2019-12-17T19:38:47+00:00

commit df5b5e555b356662a5e4a23c6774fdfce8547d54 upstream.

The touchscreen on the Teclast X89 is mounted upside down in relation to
the display orientation (the touchscreen itself is mounted upright, but the
display is mounted upside-down). Add a quirk for this so that we send
coordinates which match the display orientation.

Signed-off-by: Hans de Goede 
Reviewed-by: Bastien Nocera 
Link: https://lore.kernel.org/r/20191202085636.6650-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers

2019-12-17T19:38:46+00:00

commit a284e11c371e446371675668d8c8120a27227339 upstream.

This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.

The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.

I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.

It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.

With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.

Signed-off-by: Hans Verkuil 
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash

2019-12-17T19:38:46+00:00

commit 86bcd3a12999447faad60ec59c2d64d18d8e61ac upstream.

F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.

The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.

Fixes: 363c53875aef (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach 
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: synaptics - switch another X1 Carbon 6 to RMI/SMbus

2019-12-17T19:38:45+00:00

commit fc1156f373e3927e0dcf06678906c367588bfdd6 upstream.

Some Lenovo X1 Carbon Gen 6 laptops report LEN0091. Add this
to the smbus_pnp_ids list.

Signed-off-by: Hans Verkuil 
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191119105118.54285-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: cyttsp4_core - fix use after free bug

2019-12-17T19:37:28+00:00

[ Upstream commit 79aae6acbef16f720a7949f8fc6ac69816c79d62 ]

The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.

Signed-off-by: Pan Bian 
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

parisc: Fix HP SDC hpa address output

2019-12-05T14:37:11+00:00

[ Upstream commit c4bff35ca1bfba886da6223c9fed76a2b1382b8e ]

Show the hpa address of the HP SDC instead of a hashed value, e.g.:
HP SDC: HP SDC at 0xf0201000, IRQ 23 (NMI IRQ 24)

Signed-off-by: Helge Deller 
Signed-off-by: Sasha Levin

parisc: Fix serio address output

2019-12-05T14:37:11+00:00

[ Upstream commit 785145171d17af2554128becd6a7c8f89e101141 ]

We want the hpa addresses printed in the serio modules, not some
virtual ioremap()ed address, e.g.:

 serio: gsc-ps2-keyboard port at 0xf0108000 irq 22 @ 2:0:11
 serio: gsc-ps2-mouse port at 0xf0108100 irq 22 @ 2:0:12

Signed-off-by: Helge Deller 
Signed-off-by: Sasha Levin