linux-stable.git/drivers/input/touchscreen, branch v5.16.3

Input: ti_am335x_tsc - fix STEPCONFIG setup for Z2

2022-01-27T11:02:39+00:00

[ Upstream commit 6bfeb6c21e1bdc11c328b7d996d20f0f73c6b9b0 ]

The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.

Fixes: 8c896308feae ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi 
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: ti_am335x_tsc - set ADCREFM for X configuration

2022-01-27T11:02:38+00:00

[ Upstream commit 73cca71a903202cddc8279fc76b2da4995da5bea ]

As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".

Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.

Fixes: 1b8be32e6914 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi 
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2022-01-09T18:49:12+00:00

Pull input fix from Dmitry Torokhov:
 "A small fixup to the Zinitix touchscreen driver to avoid enabling the
  IRQ line before we successfully requested it"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: zinitix - make sure the IRQ is allocated before it gets enabled

Input: zinitix - make sure the IRQ is allocated before it gets enabled

2022-01-09T07:24:28+00:00

Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.

Fix that by moving the irq request before the input device registration.

Reviewed-by: Linus Walleij 
Fixes: 26822652c85e ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin 
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2021-12-25T21:00:14+00:00

Pull input fixes from Dmitry Torokhov:
 "A few small updates to drivers.

  Of note we are now deferring probes of i8042 on some Asus devices as
  the controller is not ready to respond to queries first time around
  when the driver is compiled into the kernel"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
  Input: atmel_mxt_ts - fix double free in mxt_read_info_block
  Input: goodix - fix memory leak in goodix_firmware_upload
  Input: goodix - add id->model mapping for the "9111" model
  Input: goodix - try not to touch the reset-pin on x86/ACPI devices
  Input: i8042 - enable deferred probe quirk for ASUS UM325UA
  Input: elantech - fix stack out of bound access in elantech_change_report_id()
  Input: iqs626a - prohibit inlining of channel parsing functions
  Input: i8042 - add deferred probe support

Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312

2021-12-20T09:01:05+00:00

The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.

Signed-off-by: Johnny Chuang 
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov

Input: atmel_mxt_ts - fix double free in mxt_read_info_block

2021-12-13T05:08:59+00:00

The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.

Return instead of jumping to avoid a double free.

Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67ef74 ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito 
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov

Input: goodix - fix memory leak in goodix_firmware_upload

2021-12-10T05:20:29+00:00

Addresses-Coverity-ID: 1493934 ("Resource leak")
Signed-off-by: José Expósito 
Link: https://lore.kernel.org/r/20211208173321.26659-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov

Input: goodix - add id->model mapping for the "9111" model

2021-12-07T07:33:47+00:00

Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.

Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Input: goodix - try not to touch the reset-pin on x86/ACPI devices

2021-12-07T07:18:24+00:00

Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.

Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.

But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca91b ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").

And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.

This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov