linux-stable.git/drivers/input/touchscreen, branch v5.15.63

Input: exc3000 - fix return value check of wait_for_completion_timeout

2022-08-25T09:40:08+00:00

commit 6bb7144c3fa16a5efb54a8e2aff1817b4168018e upstream.

wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.

Fixes: 102feb1ddfd0 ("Input: exc3000 - factor out vendor data request")
Signed-off-by: Miaoqian Lin 
Link: https://lore.kernel.org/r/20220411105828.22140-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - try not to touch the reset-pin on x86/ACPI devices

2022-07-12T14:34:51+00:00

[ Upstream commit a2fd46cd3dbb83b373ba74f4043f8dae869c65f1 ]

Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.

Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.

But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca91b ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").

And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.

This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - refactor reset handling

2022-07-12T14:34:51+00:00

[ Upstream commit 209bda4741f68f102cf2f272227bfc938e387b51 ]

Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.

Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.

This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - add a goodix.h header file

2022-07-12T14:34:51+00:00

[ Upstream commit a2233cb7b65a017067e2f2703375ecc930a0ab30 ]

Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.

This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.

Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - change goodix_i2c_write() len parameter type to int

2022-07-12T14:34:51+00:00

[ Upstream commit 31ae0102a34ed863c7d32b10e768036324991679 ]

Change the type of the goodix_i2c_write() len parameter to from 'unsigned'
to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes
goodix_i2c_write()' prototype consistent with goodix_i2c_read().

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: stmfts - do not leave device disabled in stmfts_input_open

2022-06-09T08:23:13+00:00

[ Upstream commit 5f76955ab1e43e5795a9631b22ca4f918a0ae986 ]

The commit 26623eea0da3 attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.

Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.

Fixes: 26623eea0da3 ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: ili210x - fix reset timing

2022-05-25T07:57:36+00:00

commit e4920d42ce0e9c8aafb7f64b6d9d4ae02161e51e upstream.

According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.

This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.

Fixes: 201f3c803544c ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut 
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: stmfts - fix reference leak in stmfts_input_open

2022-05-25T07:57:24+00:00

[ Upstream commit 26623eea0da3476446909af96c980768df07bbd9 ]

pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stmfts_input_open, so we should fix it.

Signed-off-by: Zheng Yongjun 
Link: https://lore.kernel.org/r/20220317131604.53538-1-zhengyongjun3@huawei.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: zinitix - do not report shadow fingers

2022-04-08T12:22:47+00:00

[ Upstream commit e941dc13fd3717122207d74539ab95da07ef797f ]

I observed the following problem with the BT404 touch pad
running the Phosh UI:

When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".

After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).

DOWN
  Zinitix-TS 3-0020: finger 0 down (246, 395)
  Zinitix-TS 3-0020: finger 1 up (0, 0)
  Zinitix-TS 3-0020: finger 2 down (246, 395)
  Zinitix-TS 3-0020: finger 3 up (0, 0)
  Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
  Zinitix-TS 3-0020: finger 0 up (246, 395)
  Zinitix-TS 3-0020: finger 2 up (246, 395)
  Zinitix-TS 3-0020: finger 4 up (246, 395)

This is one touch and release: i.e. this is all reported on
touch (down) and release.

There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.

Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.

Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.

Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.

After this my Zinitix BT404 touchscreen report fingers
flawlessly.

The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:

  if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
      touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;

As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.

Signed-off-by: Linus Walleij 
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: ti_am335x_tsc - fix STEPCONFIG setup for Z2

2022-03-08T18:12:35+00:00

[ Upstream commit 6bfeb6c21e1bdc11c328b7d996d20f0f73c6b9b0 ]

The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.

Fixes: 8c896308feae ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi 
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin