linux-stable.git/drivers/input/touchscreen, branch v5.15.136

Input: goodix - ensure int GPIO is in input for gpio_count == 1 && gpio_int_idx == 0 case

2023-10-19T21:05:37+00:00

commit 423622a90abb243944d1517b9f57db53729e45c4 upstream.

Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().

It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.

This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.

This part was already fixed in commit 3de93e6ed2df ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.

But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:

[    9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[    9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[    9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[    9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[    9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[    9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[    9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5

Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).

Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.

Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.

Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: raspberrypi-ts - fix refcount leak in rpi_ts_probe

2023-05-11T14:00:36+00:00

[ Upstream commit 5bca3688bdbc3b58a2894b8671a8e2378efe28bd ]

rpi_firmware_get() take reference, we need to release it in error paths
as well. Use devm_rpi_firmware_get() helper to handling the resources.
Also remove the existing rpi_firmware_put().

Fixes: 0b9f28fed3f7 ("Input: add official Raspberry Pi's touchscreen driver")
Fixes: 3b8ddff780b7 ("input: raspberrypi-ts: Release firmware handle when not needed")
Signed-off-by: Miaoqian Lin 
Reviewed-by: Mattijs Korpershoek 
Link: https://lore.kernel.org/r/20221223074657.810346-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - add Lenovo Yoga Book X90F to nine_bytes_report DMI table

2023-04-05T09:24:59+00:00

commit 8a0432bab6ea3203d220785da7ab3c7677f70ecb upstream.

The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.

When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.

Signed-off-by: Hans de Goede 
Reviewed-by: Bastien Nocera 
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: elants_i2c - properly handle the reset GPIO when power is off

2022-12-31T12:14:10+00:00

[ Upstream commit a85fbd6498441694475716a4d5c65f9d3e073faf ]

As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.

We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:

  devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);

While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.

Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).

Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.

Fixes: afe10358e47a ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson 
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: raydium_ts_i2c - fix memory leak in raydium_i2c_send()

2022-12-08T10:28:45+00:00

commit 8c9a59939deb4bfafdc451100c03d1e848b4169b upstream.

There is a kmemleak when test the raydium_i2c_ts with bpf mock device:

  unreferenced object 0xffff88812d3675a0 (size 8):
    comm "python3", pid 349, jiffies 4294741067 (age 95.695s)
    hex dump (first 8 bytes):
      11 0e 10 c0 01 00 04 00                          ........
    backtrace:
      [<0000000068427125>] __kmalloc+0x46/0x1b0
      [<0000000090180f91>] raydium_i2c_send+0xd4/0x2bf [raydium_i2c_ts]
      [<000000006e631aee>] raydium_i2c_initialize.cold+0xbc/0x3e4 [raydium_i2c_ts]
      [<00000000dc6fcf38>] raydium_i2c_probe+0x3cd/0x6bc [raydium_i2c_ts]
      [<00000000a310de16>] i2c_device_probe+0x651/0x680
      [<00000000f5a96bf3>] really_probe+0x17c/0x3f0
      [<00000000096ba499>] __driver_probe_device+0xe3/0x170
      [<00000000c5acb4d9>] driver_probe_device+0x49/0x120
      [<00000000264fe082>] __device_attach_driver+0xf7/0x150
      [<00000000f919423c>] bus_for_each_drv+0x114/0x180
      [<00000000e067feca>] __device_attach+0x1e5/0x2d0
      [<0000000054301fc2>] bus_probe_device+0x126/0x140
      [<00000000aad93b22>] device_add+0x810/0x1130
      [<00000000c086a53f>] i2c_new_client_device+0x352/0x4e0
      [<000000003c2c248c>] of_i2c_register_device+0xf1/0x110
      [<00000000ffec4177>] of_i2c_notify+0x100/0x160
  unreferenced object 0xffff88812d3675c8 (size 8):
    comm "python3", pid 349, jiffies 4294741070 (age 95.692s)
    hex dump (first 8 bytes):
      22 00 36 2d 81 88 ff ff                          ".6-....
    backtrace:
      [<0000000068427125>] __kmalloc+0x46/0x1b0
      [<0000000090180f91>] raydium_i2c_send+0xd4/0x2bf [raydium_i2c_ts]
      [<000000001d5c9620>] raydium_i2c_initialize.cold+0x223/0x3e4 [raydium_i2c_ts]
      [<00000000dc6fcf38>] raydium_i2c_probe+0x3cd/0x6bc [raydium_i2c_ts]
      [<00000000a310de16>] i2c_device_probe+0x651/0x680
      [<00000000f5a96bf3>] really_probe+0x17c/0x3f0
      [<00000000096ba499>] __driver_probe_device+0xe3/0x170
      [<00000000c5acb4d9>] driver_probe_device+0x49/0x120
      [<00000000264fe082>] __device_attach_driver+0xf7/0x150
      [<00000000f919423c>] bus_for_each_drv+0x114/0x180
      [<00000000e067feca>] __device_attach+0x1e5/0x2d0
      [<0000000054301fc2>] bus_probe_device+0x126/0x140
      [<00000000aad93b22>] device_add+0x810/0x1130
      [<00000000c086a53f>] i2c_new_client_device+0x352/0x4e0
      [<000000003c2c248c>] of_i2c_register_device+0xf1/0x110
      [<00000000ffec4177>] of_i2c_notify+0x100/0x160

After BANK_SWITCH command from i2c BUS, no matter success or error
happened, the tx_buf should be freed.

Fixes: 3b384bd6c3f2 ("Input: raydium_ts_i2c - do not split tx transactions")
Signed-off-by: Zhang Xiaoxu 
Link: https://lore.kernel.org/r/20221202103412.2120169-1-zhangxiaoxu5@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - try resetting the controller when no config is set

2022-12-02T16:41:10+00:00

[ Upstream commit c7e37cc6240767f794678d11704935d49cc81d59 ]

On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.

On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.

To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().

This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.

Signed-off-by: Hans de Goede 
Reviewed-by: Bastien Nocera 
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: melfas_mip4 - fix return value check in mip4_probe()

2022-10-05T08:39:42+00:00

[ Upstream commit a54dc27bd25f20ee3ea2009584b3166d25178243 ]

devm_gpiod_get_optional() may return ERR_PTR(-EPROBE_DEFER),
add a minus sign to fix it.

Fixes: 6ccb1d8f78bd ("Input: add MELFAS MIP4 Touchscreen driver")
Signed-off-by: Yang Yingliang 
Link: https://lore.kernel.org/r/20220924030715.1653538-1-yangyingliang@huawei.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - add compatible string for GT1158

2022-09-20T10:39:46+00:00

commit 80b9ebd3e478cd41526cbf84f80c3e0eb885d1d3 upstream.

Add compatible string for GT1158 missing from the previous patch.

Fixes: 425fe4709c76 ("Input: goodix - add support for GT1158")
Signed-off-by: Jarrah Gosbell 
Link: https://lore.kernel.org/r/20220813043821.9981-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - add support for GT1158

2022-09-20T10:39:43+00:00

[ Upstream commit 425fe4709c76e35f93f4c0e50240f0b61b2a2e54 ]

This controller is used by PinePhone and PinePhone Pro. Support for
the PinePhone Pro will be added in a later patch set.

Signed-off-by: Ondrej Jirman 
Signed-off-by: Jarrah Gosbell 
Reviewed-by: Hans de Goede 
Link: https://lore.kernel.org/r/20220809091200.290492-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: exc3000 - fix return value check of wait_for_completion_timeout

2022-08-25T09:40:08+00:00

commit 6bb7144c3fa16a5efb54a8e2aff1817b4168018e upstream.

wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.

Fixes: 102feb1ddfd0 ("Input: exc3000 - factor out vendor data request")
Signed-off-by: Miaoqian Lin 
Link: https://lore.kernel.org/r/20220411105828.22140-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman