commit b27c0d0c3bf3073e8ae19875eb1d3755c5e8c072 upstream.

"calibrate" attribute does not provide "show" methods and thus we should
not mark it as readable.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 12afb34400eb2b301f06b2aa3535497d14faee59 upstream.

Somehow the patch that added two-finger touch support forgot to update
W8001_MAX_LENGTH from 11 to 13.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 879f2fea8a5a748bcbf98d2cdce9139c045505d3 upstream.

According to the touch controller spec, SPI return a 16 bit value, only 12
bits are valid, they are bit[14-3].

The value of MISO and MOSI can be configured when SPI is in idle mode.
Currently this touch driver assumes the SPI bus sets the MOSI and MISO in
low level when SPI bus is in idle mode. So the bit[15] of the value got
from SPI bus is always 0. But when SPI bus congfigures the MOSI and MISO in
high level during the SPI idle mode, the bit[15] of the value get from SPI
is always 1. If bit[15] is not masked, we may get the wrong value.

Mask the invalid bit to make sure the correct value gets returned.
Regardless of the SPI bus idle configuration.

Signed-off-by: Andrey Gelman <andrey.gelman@compulab.co.il>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 968491709e5b1aaf429428814fff3d932fa90b60 upstream.

This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen.  Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.

According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.

The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.

Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit dbea4032f8024e5ea886341f7c39cf023e30e828 upstream.

This adds support for another model of IRTOUCH SYSTEMS Co.,LtD infrared
touchscreens. The USB vendorID/deviceID is 6615/0012. It is also sold
under the label "Elektrosil".

The datasheet states that coordinates for x and y are in the range from
0 to 32767.

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 859abd1d59e2db07d2e4db27074fc33568353d11 upstream.

Sharp SL-6000 (tosa) touchscreen needs wider limits to properly map all
points on the screen. Expand ranges in abs_x and abs_y arrays according
to the touchscreen area.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 4ef38351d770cc421f4a0c7a849fd13207fc5741 upstream.

This patch supports the separate handling of the USB transfer buffer length
and the length of the buffer used for multi packet support. For devices
supporting multiple report or diagnostic packets, the USB transfer size is now
limited to the USB endpoints wMaxPacketSize - otherwise it defaults to the
configured report packet size as before.

This fixes an issue where event reporting can be delayed for an arbitrary
time for multi packet devices. For instance the report size for eGalax devices
is defined to the 16 byte maximum diagnostic packet size as opposed to the 5
byte report packet size. In case the driver requests 16 byte from the USB
interrupt endpoint, the USB host controller driver needs to split up the
request into 2 accesses according to the endpoints wMaxPacketSize of 8 byte.
When the first transfer is answered by the eGalax device with not less than
the full 8 byte requested, the host controller has got no way of knowing
whether the touch controller has got additional data queued and will issue
the second transfer. If per example a liftoff event finishes at such a
wMaxPacketSize boundary, the data will not be available to the usbtouch driver
until a further event is triggered and transfered to the host. From user
perspective the BTN_TOUCH release event in this case is stuck until the next
touch down event.

Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ae2aa3a512fa5f50f67feba9e66bc2efb394bd63 upstream.

The HID driver now handles these devices, regardless of what protocol
the device claims it supports.

Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Pull input updates from Dmitry Torokhov:
 "A new driver for slidebar on Ideapad laptops and a bunch of assorted
  driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
  Input: add SYN_MAX and SYN_CNT constants
  Input: max11801_ts - convert to devm
  Input: egalax-ts - fix typo and improve text
  Input: MAINTAINERS - change maintainer for cyttsp driver
  Input: cyttsp4 - kill 'defined but not used' compiler warnings
  Input: add driver for slidebar on Lenovo IdeaPad laptops
  Input: omap-keypad - set up irq type from DT
  Input: omap-keypad - enable wakeup capability for keypad.
  Input: omap-keypad - clear interrupts on open
  Input: omap-keypad - convert to threaded IRQ
  Input: omap-keypad - use bitfiled instead of hardcoded values
  Input: cyttsp4 - remove useless NULL test from cyttsp4_watchdog_timer()
  Input: wacom - fix error return code in wacom_probe()
  Input: as5011 - fix error return code in as5011_probe()
  Input: keyboard, serio - simplify use of devm_ioremap_resource
  Input: tegra-kbc - simplify use of devm_ioremap_resource
  Input: htcpen - fix incorrect placement of __initdata
  Input: qt1070 - add power management ops
  Input: wistron_btns - add MODULE_DEVICE_TABLE
  Input: wistron_btns - mark the Medion MD96500 keymap as tested
  ...