linux-stable.git/drivers/input/touchscreen, branch linux-5.16.y

Input: zinitix - do not report shadow fingers

2022-04-08T12:05:18+00:00

[ Upstream commit e941dc13fd3717122207d74539ab95da07ef797f ]

I observed the following problem with the BT404 touch pad
running the Phosh UI:

When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".

After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).

DOWN
  Zinitix-TS 3-0020: finger 0 down (246, 395)
  Zinitix-TS 3-0020: finger 1 up (0, 0)
  Zinitix-TS 3-0020: finger 2 down (246, 395)
  Zinitix-TS 3-0020: finger 3 up (0, 0)
  Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
  Zinitix-TS 3-0020: finger 0 up (246, 395)
  Zinitix-TS 3-0020: finger 2 up (246, 395)
  Zinitix-TS 3-0020: finger 4 up (246, 395)

This is one touch and release: i.e. this is all reported on
touch (down) and release.

There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.

Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.

Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.

Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.

After this my Zinitix BT404 touchscreen report fingers
flawlessly.

The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:

  if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
      touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;

As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.

Signed-off-by: Linus Walleij 
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - workaround Cherry Trail devices with a bogus ACPI Interrupt() resource

2022-03-19T12:48:44+00:00

[ Upstream commit d982992669733dd75520000c6057d8ee0725a363 ]

ACPI/x86 devices with a Cherry Trail SoC should have a GpioInt + a regular
GPIO ACPI resource in their ACPI tables.

Some CHT devices have a bug, where the also is bogus interrupt resource
(likely copied from a previous Bay Trail based generation of the device).

The i2c-core-acpi code will assign the bogus, non-working, interrupt
resource to client->irq. Add a workaround to fix this up.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2043960
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20220228111613.363336-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - use the new soc_intel_is_byt() helper

2022-03-19T12:48:44+00:00

[ Upstream commit d176708ffc20332d1c730098d2b111e0b77ece82 ]

Use the new soc_intel_is_byt() helper from linux/platform_data/x86/soc.h.

Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20220131143539.109142-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: ti_am335x_tsc - fix STEPCONFIG setup for Z2

2022-01-27T11:02:39+00:00

[ Upstream commit 6bfeb6c21e1bdc11c328b7d996d20f0f73c6b9b0 ]

The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.

Fixes: 8c896308feae ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi 
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: ti_am335x_tsc - set ADCREFM for X configuration

2022-01-27T11:02:38+00:00

[ Upstream commit 73cca71a903202cddc8279fc76b2da4995da5bea ]

As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".

Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.

Fixes: 1b8be32e6914 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi 
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2022-01-09T18:49:12+00:00

Pull input fix from Dmitry Torokhov:
 "A small fixup to the Zinitix touchscreen driver to avoid enabling the
  IRQ line before we successfully requested it"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: zinitix - make sure the IRQ is allocated before it gets enabled

Input: zinitix - make sure the IRQ is allocated before it gets enabled

2022-01-09T07:24:28+00:00

Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.

Fix that by moving the irq request before the input device registration.

Reviewed-by: Linus Walleij 
Fixes: 26822652c85e ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin 
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2021-12-25T21:00:14+00:00

Pull input fixes from Dmitry Torokhov:
 "A few small updates to drivers.

  Of note we are now deferring probes of i8042 on some Asus devices as
  the controller is not ready to respond to queries first time around
  when the driver is compiled into the kernel"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
  Input: atmel_mxt_ts - fix double free in mxt_read_info_block
  Input: goodix - fix memory leak in goodix_firmware_upload
  Input: goodix - add id->model mapping for the "9111" model
  Input: goodix - try not to touch the reset-pin on x86/ACPI devices
  Input: i8042 - enable deferred probe quirk for ASUS UM325UA
  Input: elantech - fix stack out of bound access in elantech_change_report_id()
  Input: iqs626a - prohibit inlining of channel parsing functions
  Input: i8042 - add deferred probe support

Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312

2021-12-20T09:01:05+00:00

The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.

Signed-off-by: Johnny Chuang 
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov

Input: atmel_mxt_ts - fix double free in mxt_read_info_block

2021-12-13T05:08:59+00:00

The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.

Return instead of jumping to avoid a double free.

Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67ef74 ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito 
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov