linux-stable.git/drivers/input/touchscreen/goodix.c, branch v5.16.2

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2021-12-25T21:00:14+00:00

Pull input fixes from Dmitry Torokhov:
 "A few small updates to drivers.

  Of note we are now deferring probes of i8042 on some Asus devices as
  the controller is not ready to respond to queries first time around
  when the driver is compiled into the kernel"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
  Input: atmel_mxt_ts - fix double free in mxt_read_info_block
  Input: goodix - fix memory leak in goodix_firmware_upload
  Input: goodix - add id->model mapping for the "9111" model
  Input: goodix - try not to touch the reset-pin on x86/ACPI devices
  Input: i8042 - enable deferred probe quirk for ASUS UM325UA
  Input: elantech - fix stack out of bound access in elantech_change_report_id()
  Input: iqs626a - prohibit inlining of channel parsing functions
  Input: i8042 - add deferred probe support

Input: goodix - add id->model mapping for the "9111" model

2021-12-07T07:33:47+00:00

Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.

Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Input: goodix - try not to touch the reset-pin on x86/ACPI devices

2021-12-07T07:18:24+00:00

Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.

Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.

But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca91b ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").

And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.

This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2021-11-12T19:53:16+00:00

Pull input updates from Dmitry Torokhov:
 "Just one new driver (Cypress StreetFighter touchkey), and no input
  core changes this time.

  Plus various fixes and enhancements to existing drivers"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
  Input: iforce - fix control-message timeout
  Input: wacom_i2c - use macros for the bit masks
  Input: ili210x - reduce sample period to 15ms
  Input: ili210x - improve polled sample spacing
  Input: ili210x - special case ili251x sample read out
  Input: elantench - fix misreporting trackpoint coordinates
  Input: synaptics-rmi4 - Fix device hierarchy
  Input: i8042 - Add quirk for Fujitsu Lifebook T725
  Input: cap11xx - add support for cap1206
  Input: remove unused header 
  Input: ili210x - add ili251x firmware update support
  Input: ili210x - export ili251x version details via sysfs
  Input: ili210x - use resolution from ili251x firmware
  Input: pm8941-pwrkey - respect reboot_mode for warm reset
  reboot: export symbol 'reboot_mode'
  Input: max77693-haptic - drop unneeded MODULE_ALIAS
  Input: cpcap-pwrbutton - do not set input parent explicitly
  Input: max8925_onkey - don't mark comment as kernel-doc
  Input: ads7846 - do not attempt IRQ workaround when deferring probe
  Input: ads7846 - use input_set_capability()
  ...

Input: goodix - add support for controllers without flash

2021-09-21T05:00:29+00:00

Some Goodix touchscreen controllers, such as for example the GT912,
don't have flash-storage for their firmware.

These models require the OS to load the firmware at runtime, as well as
some other special handling. Add support for this to the goodix driver.

This patch was developed and tested on a Glavey TM800A550L tablet.

Note the "goodix,main-clk" and "firmware-name" device-properties used
by the new code are *not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.

Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this properties for now is purely a kernel-internal thing and
the name/working of the properties may still be changed for now.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-7-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Input: goodix - allow specifying the config filename

2021-09-21T05:00:28+00:00

The config which needs to be send to the controller on some device-models
is model-specific. Allow specifying a model-specific filename through
a device-property, rather then always using a fixed filename.

Note the "goodix,config-name" device-property used by this is
*not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.

Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this property for now is purely a kernel-internal thing and
the name/working of the property may still be changed for now.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-6-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Input: goodix - push error logging up into i2c_read and i2c_write helpers

2021-09-21T05:00:26+00:00

Make the goodix_i2c_read() and goodix_i2c_write*() helpers log errors
themselves. This allows removing all the error logging from their callers.

This already results in a nice cleanup with the current code and it also
helps to make the upcoming support for controllers without flash cleaner.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Input: goodix - refactor reset handling

2021-09-21T05:00:25+00:00

Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.

Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.

This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Input: goodix - add a goodix.h header file

2021-09-21T05:00:23+00:00

Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.

This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.

Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Input: goodix - change goodix_i2c_write() len parameter type to int

2021-09-21T05:00:22+00:00

Change the type of the goodix_i2c_write() len parameter to from 'unsigned'
to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes
goodix_i2c_write()' prototype consistent with goodix_i2c_read().

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov