linux-stable.git/drivers/input/touchscreen/goodix.c, branch linux-6.5.y

Input: goodix - ensure int GPIO is in input for gpio_count == 1 && gpio_int_idx == 0 case

2023-10-19T21:11:06+00:00

commit 423622a90abb243944d1517b9f57db53729e45c4 upstream.

Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().

It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.

This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.

This part was already fixed in commit 3de93e6ed2df ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.

But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:

[    9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[    9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[    9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[    9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[    9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[    9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[    9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5

Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).

Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.

Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.

Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Merge branch 'next' into for-linus

2023-06-26T22:18:13+00:00

Prepare input updates for 6.5 merge window.

Input: Switch i2c drivers back to use .probe()

2023-05-17T16:59:11+00:00

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König 
Link: https://lore.kernel.org/r/20230517164645.162294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov

Input: goodix - add Lenovo Yoga Book X90F to nine_bytes_report DMI table

2023-03-17T10:24:40+00:00

The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.

When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.

Signed-off-by: Hans de Goede 
Reviewed-by: Bastien Nocera 
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Merge tag 'v6.2-rc3' into next

2023-01-10T04:28:19+00:00

Merge with mainline to bring in timer_shutdown_sync() API.

Input: goodix - switch to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()

2023-01-10T04:25:25+00:00

SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings.  The new combination of pm_sleep_ptr()
and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.

Signed-off-by: Jonathan Cameron 
Cc: Hans de Goede 
Cc: Bastien Nocera 
Reviewed-by: Hans de Goede 
Reviewed-by: Linus Walleij 
Link: https://lore.kernel.org/r/20230102181842.718010-47-jic23@kernel.org
Signed-off-by: Dmitry Torokhov

Merge branch 'next' into for-linus

2022-12-12T18:47:03+00:00

Prepare input updates for 6.2 merge window.

Input: goodix - Convert to i2c's .probe_new()

2022-12-02T22:53:45+00:00

The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.

Signed-off-by: Uwe Kleine-König 
Reviewed-by: Hans de Goede 
Link: https://lore.kernel.org/r/20221118224540.619276-242-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov

Input: goodix - try resetting the controller when no config is set

2022-11-03T19:49:35+00:00

On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.

On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.

To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().

This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.

Signed-off-by: Hans de Goede 
Reviewed-by: Bastien Nocera 
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov

Merge branch 'next' into for-linus

2022-10-10T05:30:23+00:00

Prepare input updates for 6.1 merge window.