linux-stable.git/drivers/input/touchscreen/goodix.c, branch linux-5.15.y

Input: goodix - use the new soc_intel_is_byt() helper

2024-10-17T13:11:09+00:00

commit d176708ffc20332d1c730098d2b111e0b77ece82 upstream.

Use the new soc_intel_is_byt() helper from linux/platform_data/x86/soc.h.

Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20220131143539.109142-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Ricardo Neri 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - ensure int GPIO is in input for gpio_count == 1 && gpio_int_idx == 0 case

2023-10-19T21:05:37+00:00

commit 423622a90abb243944d1517b9f57db53729e45c4 upstream.

Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().

It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.

This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.

This part was already fixed in commit 3de93e6ed2df ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.

But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:

[    9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[    9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[    9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[    9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[    9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[    9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[    9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5

Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).

Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.

Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.

Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - add Lenovo Yoga Book X90F to nine_bytes_report DMI table

2023-04-05T09:24:59+00:00

commit 8a0432bab6ea3203d220785da7ab3c7677f70ecb upstream.

The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.

When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.

Signed-off-by: Hans de Goede 
Reviewed-by: Bastien Nocera 
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - try resetting the controller when no config is set

2022-12-02T16:41:10+00:00

[ Upstream commit c7e37cc6240767f794678d11704935d49cc81d59 ]

On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.

On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.

To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().

This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.

Signed-off-by: Hans de Goede 
Reviewed-by: Bastien Nocera 
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - add compatible string for GT1158

2022-09-20T10:39:46+00:00

commit 80b9ebd3e478cd41526cbf84f80c3e0eb885d1d3 upstream.

Add compatible string for GT1158 missing from the previous patch.

Fixes: 425fe4709c76 ("Input: goodix - add support for GT1158")
Signed-off-by: Jarrah Gosbell 
Link: https://lore.kernel.org/r/20220813043821.9981-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

Input: goodix - add support for GT1158

2022-09-20T10:39:43+00:00

[ Upstream commit 425fe4709c76e35f93f4c0e50240f0b61b2a2e54 ]

This controller is used by PinePhone and PinePhone Pro. Support for
the PinePhone Pro will be added in a later patch set.

Signed-off-by: Ondrej Jirman 
Signed-off-by: Jarrah Gosbell 
Reviewed-by: Hans de Goede 
Link: https://lore.kernel.org/r/20220809091200.290492-1-kernel@undef.tools
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - try not to touch the reset-pin on x86/ACPI devices

2022-07-12T14:34:51+00:00

[ Upstream commit a2fd46cd3dbb83b373ba74f4043f8dae869c65f1 ]

Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.

Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.

But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca91b ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").

And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.

This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - refactor reset handling

2022-07-12T14:34:51+00:00

[ Upstream commit 209bda4741f68f102cf2f272227bfc938e387b51 ]

Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.

Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.

This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - add a goodix.h header file

2022-07-12T14:34:51+00:00

[ Upstream commit a2233cb7b65a017067e2f2703375ecc930a0ab30 ]

Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.

This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.

Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin

Input: goodix - change goodix_i2c_write() len parameter type to int

2022-07-12T14:34:51+00:00

[ Upstream commit 31ae0102a34ed863c7d32b10e768036324991679 ]

Change the type of the goodix_i2c_write() len parameter to from 'unsigned'
to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes
goodix_i2c_write()' prototype consistent with goodix_i2c_read().

Reviewed-by: Bastien Nocera 
Signed-off-by: Hans de Goede 
Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sasha Levin