linux-stable.git/drivers/input/mouse, branch linux-3.4.y

Input: elantech - fix detection of touchpads where the revision matches a known rate

2015-09-18T01:20:44+00:00

commit 5f0ee9d17aae628b22be86966471db65be21f262 upstream.

Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.

This fixes the touchpad not being detected properly on Asus PU551LA
laptops.

Reported-and-tested-by: David Zafra Gómez 
Signed-off-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li

Input: elantech - fix semi-mt protocol for v3 HW

2015-09-18T01:20:41+00:00

commit 3c0213d17a09601e0c6c0ae0e27caf70d988290f upstream.

When the v3 hardware sees more than one finger, it uses the semi-mt
protocol to report the touches. However, it currently works when
num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1
finger as if num_fingers was 1.

This confuses userspace which knows how to deal with extra fingers
when all the slots are used, but not when some are missing.

Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101

Signed-off-by: Benjamin Tissoires 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li

Input: elantech - fix absolute mode setting on some ASUS laptops

2015-09-18T01:20:27+00:00

commit bd884149aca61de269fd9bad83fe2a4232ffab21 upstream.

On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.

In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).

Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c

Reported-and-tested-by: George Moutsopoulos 
Signed-off-by: Ulrik De Bie 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li

Input: synaptics - handle spurious release of trackstick buttons

2015-06-19T03:40:26+00:00

commit ebc80840b850db72f7ae84fbcf77630ae5409629 upstream.

The Fimware 8.1 has a bug in which the extra buttons are only sent when the
ExtBit is 1.  This should be fixed in a future FW update which should have
a bump of the minor version.

Signed-off-by: Benjamin Tissoires 
Acked-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li

Input: synaptics - fix middle button on Lenovo 2015 products

2015-06-19T03:40:26+00:00

commit dc5465dc8a6d5cae8a0e1d8826bdcb2e4cb261ab upstream.

On the X1 Carbon 3rd gen (with a 2015 broadwell cpu), the physical middle
button of the trackstick (attached to the touchpad serio device, of course)
seems to get lost.

Actually, the touchpads reports 3 extra buttons, which falls in the switch
below to the '2' case. Let's handle the case of odd numbers also, so that
the middle button finds its way back.

Signed-off-by: Benjamin Tissoires 
Acked-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov 
[lizf: Backported to 3.4: open-code GENMASK]
Signed-off-by: Zefan Li

Input: synaptics - query min dimensions for fw v8.1

2015-06-19T03:40:26+00:00

commit ac097930f0730a9b777737de2b51e0fc49d2be7a upstream.

Query the min dimensions even if the check
SYN_EXT_CAP_REQUESTS(priv->capabilities) >= 7 fails, but we know that the
firmware version 8.1 is safe.

With that we don't need quirks for post-2013 models anymore as they expose
correct min and max dimensions.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541

Signed-off-by: Daniel Martin 
  re-order the tests to check SYN_CAP_MIN_DIMENSIONS even on FW 8.1
Signed-off-by: Benjamin Tissoires 
Acked-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li

Input: alps - allow up to 2 invalid packets without resetting device

2015-02-02T09:05:19+00:00

commit 9d720b34c0a432639252f63012e18b0507f5b432 upstream.

On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.

This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.

Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.

Signed-off-by: Pali Rohár 
Tested-by: Pali Rohár 
Reviewed-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li

Input: alps - ignore potential bare packets when device is out of sync

2015-02-02T09:05:18+00:00

commit 4ab8f7f320f91f279c3f06a9795cfea5c972888a upstream.

5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.

It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.

Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.

This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.

So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.

Signed-off-by: Pali Rohár 
Tested-by: Pali Rohár 
Reviewed-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li

Input: synaptics - gate forcepad support by DMI check

2015-02-02T09:04:49+00:00

commit aa972409951e0675e07918620427517cad5090e0 upstream.

Unfortunately, ForcePad capability is not actually exported over PS/2, so
we have to resort to DMI checks.

Reported-by: Nicole Faerber 
Signed-off-by: Dmitry Torokhov 
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li

Input: synaptics - add support for ForcePads

2014-12-01T10:02:28+00:00

commit 5715fc764f7753d464dbe094b5ef9cffa6e479a4 upstream.

ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of
physical buttons, instead they generate primary button click when user
presses somewhat hard on the surface of the touchpad. Unfortunately they
also report primary button click whenever there are 2 or more contacts
on the pad, messing up all multi-finger gestures (2-finger scrolling,
multi-finger tapping, etc). To cope with this behavior we introduce a
delay (currently 50 msecs) in reporting primary press in case more
contacts appear.

Reviewed-by: Hans de Goede 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Zefan Li