linux-stable.git/drivers/iio, branch v6.4.2 Linux kernel stable tree iio: imu: inv_icm42600: fix timestamp reset 2023-05-20T16:33:14+00:00 Jean-Baptiste Maneyrol jean-baptiste.maneyrol@tdk.com 2023-05-09T15:22:02+00:00 bbaae0c79ebd49f61ad942a8bf9e12bfc7f821bb Timestamp reset is not done in the correct place. It must be done before enabling buffer. The reason is that interrupt timestamping is always happening when the chip is on, even if the corresponding sensor is off. When the sensor restarts, timestamp is wrong if you don't do a reset first. Fixes: ec74ae9fd37c ("iio: imu: inv_icm42600: add accurate timestamping") Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20230509152202.245444-1-inv.git-commit@tdk.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
Timestamp reset is not done in the correct place. It must be done
before enabling buffer. The reason is that interrupt timestamping
is always happening when the chip is on, even if the
corresponding sensor is off. When the sensor restarts, timestamp
is wrong if you don't do a reset first.

Fixes: ec74ae9fd37c ("iio: imu: inv_icm42600: add accurate timestamping")
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230509152202.245444-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: adc: ad_sigma_delta: Fix IRQ issue by setting IRQ_DISABLE_UNLAZY flag 2023-05-20T15:34:52+00:00 Masahiro Honda honda@mechatrax.com 2023-05-18T11:08:16+00:00 626d312028bec44209d0ecd5beaa9b1aa8945f7d The Sigma-Delta ADCs supported by this driver can use SDO as an interrupt line to indicate the completion of a conversion. However, some devices cannot properly detect the completion of a conversion by an interrupt. This is for the reason mentioned in the following commit. commit e9849777d0e2 ("genirq: Add flag to force mask in disable_irq[_nosync]()") A read operation is performed by an extra interrupt before the completion of a conversion. At this time, the value read from the ADC data register is the same as the previous conversion result. This patch fixes the issue by setting IRQ_DISABLE_UNLAZY flag. Fixes: 0c6ef985a1fd ("iio: adc: ad7791: fix IRQ flags") Fixes: 1a913270e57a ("iio: adc: ad7793: Fix IRQ flag") Fixes: e081102f3077 ("iio: adc: ad7780: Fix IRQ flag") Fixes: 89a86da5cb8e ("iio: adc: ad7192: Add IRQ flag") Fixes: 79ef91493f54 ("iio: adc: ad7124: Set IRQ type to falling") Signed-off-by: Masahiro Honda <honda@mechatrax.com> Link: https://lore.kernel.org/r/20230518110816.248-1-honda@mechatrax.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
The Sigma-Delta ADCs supported by this driver can use SDO as an interrupt
line to indicate the completion of a conversion. However, some devices
cannot properly detect the completion of a conversion by an interrupt.
This is for the reason mentioned in the following commit.

commit e9849777d0e2 ("genirq: Add flag to force mask in
                      disable_irq[_nosync]()")

A read operation is performed by an extra interrupt before the completion
of a conversion. At this time, the value read from the ADC data register
is the same as the previous conversion result. This patch fixes the issue
by setting IRQ_DISABLE_UNLAZY flag.

Fixes: 0c6ef985a1fd ("iio: adc: ad7791: fix IRQ flags")
Fixes: 1a913270e57a ("iio: adc: ad7793: Fix IRQ flag")
Fixes: e081102f3077 ("iio: adc: ad7780: Fix IRQ flag")
Fixes: 89a86da5cb8e ("iio: adc: ad7192: Add IRQ flag")
Fixes: 79ef91493f54 ("iio: adc: ad7124: Set IRQ type to falling")
Signed-off-by: Masahiro Honda <honda@mechatrax.com>
Link: https://lore.kernel.org/r/20230518110816.248-1-honda@mechatrax.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: dac: mcp4725: Fix i2c_master_send() return value handling 2023-05-13T18:46:59+00:00 Marek Vasut marex@denx.de 2023-05-11T00:43:30+00:00 09d3bec7009186bdba77039df01e5834788b3f95 The i2c_master_send() returns number of sent bytes on success, or negative on error. The suspend/resume callbacks expect zero on success and non-zero on error. Adapt the return value of the i2c_master_send() to the expectation of the suspend and resume callbacks, including proper validation of the return value. Fixes: cf35ad61aca2 ("iio: add mcp4725 I2C DAC driver") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230511004330.206942-1-marex@denx.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.

Fixes: cf35ad61aca2 ("iio: add mcp4725 I2C DAC driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230511004330.206942-1-marex@denx.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: accel: kx022a fix irq getting 2023-05-13T18:45:08+00:00 Matti Vaittinen mazziesaccount@gmail.com 2023-05-12T07:53:41+00:00 56cd3d1c5c5b073a1a444eafdcf97d4d866d351a The fwnode_irq_get_byname() was returning 0 at device-tree mapping error. If this occurred, the KX022A driver did abort the probe but errorneously directly returned the return value from fwnode_irq_get_byname() from probe. In case of a device-tree mapping error this indicated success. The fwnode_irq_get_byname() has since been fixed to not return zero on error so the check for fwnode_irq_get_byname() can be relaxed to only treat negative values as errors. This will also do decent fix even when backported to branches where fwnode_irq_get_byname() can still return zero on error because KX022A probe should later fail at IRQ requesting and a prober error handling should follow. Relax the return value check for fwnode_irq_get_byname() to only treat negative values as errors. Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <error27@gmail.com> Closes: https://lore.kernel.org/r/202305110245.MFxC9bUj-lkp@intel.com/ Link: https://lore.kernel.org/r/202305110245.MFxC9bUj-lkp@intel.com/ Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Fixes: 7c1d1677b322 ("iio: accel: Support Kionix/ROHM KX022A accelerometer") Link: https://lore.kernel.org/r/b45b4b638db109c6078d243252df3a7b0485f7d5.1683875389.git.mazziesaccount@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
The fwnode_irq_get_byname() was returning 0 at device-tree mapping
error. If this occurred, the KX022A driver did abort the probe but
errorneously directly returned the return value from
fwnode_irq_get_byname() from probe. In case of a device-tree mapping
error this indicated success.

The fwnode_irq_get_byname() has since been fixed to not return zero on
error so the check for fwnode_irq_get_byname() can be relaxed to only
treat negative values as errors. This will also do decent fix even when
backported to branches where fwnode_irq_get_byname() can still return
zero on error because KX022A probe should later fail at IRQ requesting
and a prober error handling should follow.

Relax the return value check for fwnode_irq_get_byname() to only treat
negative values as errors.

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202305110245.MFxC9bUj-lkp@intel.com/
Link: https://lore.kernel.org/r/202305110245.MFxC9bUj-lkp@intel.com/
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 7c1d1677b322 ("iio: accel: Support Kionix/ROHM KX022A accelerometer")
Link: https://lore.kernel.org/r/b45b4b638db109c6078d243252df3a7b0485f7d5.1683875389.git.mazziesaccount@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: bu27034: Ensure reset is written 2023-05-13T18:22:01+00:00 Matti Vaittinen mazziesaccount@gmail.com 2023-05-08T11:01:25+00:00 d049151adde4ec17392592d145e94f0086f8ee80 The reset bit must be always written to the hardware no matter what value is in a cache or register. Ensure this by using regmap_write_bits() instead of the regmap_update_bits(). Furthermore, the SWRESET bit may be self-clearing, so mark the SYSTEM_CONTROL register volatile to guarantee we do also read the right state - should we ever need to read it. Finally, writing the SWRESET bit will restore the default register values. This can cause register cache to be outdated if there are any register values cached. Rebuild register cache after SWRESET and use regmap_update_bits() when performing the reset. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Fixes: e52afbd61039 ("iio: light: ROHM BU27034 Ambient Light Sensor") Link: https://lore.kernel.org/r/ZFjWhbfuN5XcKty+@fedora Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
The reset bit must be always written to the hardware no matter what value
is in a cache or register. Ensure this by using regmap_write_bits()
instead of the regmap_update_bits(). Furthermore, the SWRESET bit may be
self-clearing, so mark the SYSTEM_CONTROL register volatile to guarantee
we do also read the right state - should we ever need to read it.

Finally, writing the SWRESET bit will restore the default register
values. This can cause register cache to be outdated if there are any
register values cached.

Rebuild register cache after SWRESET and use regmap_update_bits() when
performing the reset.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: e52afbd61039 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Link: https://lore.kernel.org/r/ZFjWhbfuN5XcKty+@fedora
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: dac: build ad5758 driver when AD5758 is selected 2023-05-13T18:18:11+00:00 Lukas Bulwahn lukas.bulwahn@gmail.com 2023-05-08T04:02:08+00:00 a146eccb68be161ae9eab5f3f68bb0ed7c0fbaa8 Commit 28d1a7ac2a0d ("iio: dac: Add AD5758 support") adds the config AD5758 and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver is however included when AD5755 is selected, not when AD5758 is selected. Probably, this was simply a mistake that happened by copy-and-paste and forgetting to adjust the actual line. Surprisingly, no one has ever noticed that this driver is actually only included when AD5755 is selected and that the config AD5758 has actually no effect on the build. Fixes: 28d1a7ac2a0d ("iio: dac: Add AD5758 support") Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
Commit 28d1a7ac2a0d ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.

Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.

Fixes: 28d1a7ac2a0d ("iio: dac: Add AD5758 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: addac: ad74413: fix resistance input processing 2023-05-13T16:54:58+00:00 Rasmus Villemoes linux@rasmusvillemoes.dk 2023-05-03T09:58:17+00:00 24febc99ca725dcf42d57168a2f4e8a75a5ade92 On success, ad74413r_get_single_adc_result() returns IIO_VAL_INT aka 1. So currently, the IIO_CHAN_INFO_PROCESSED case is effectively equivalent to the IIO_CHAN_INFO_RAW case, and we never call ad74413r_adc_to_resistance_result() to convert the adc measurement to ohms. Check ret for being negative rather than non-zero. Fixes: fea251b6a5dbd (iio: addac: add AD74413R driver) Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20230503095817.452551-1-linux@rasmusvillemoes.dk Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
On success, ad74413r_get_single_adc_result() returns IIO_VAL_INT aka
1. So currently, the IIO_CHAN_INFO_PROCESSED case is effectively
equivalent to the IIO_CHAN_INFO_RAW case, and we never call
ad74413r_adc_to_resistance_result() to convert the adc measurement to
ohms.

Check ret for being negative rather than non-zero.

Fixes: fea251b6a5dbd (iio: addac: add AD74413R driver)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230503095817.452551-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: light: vcnl4035: fixed chip ID check 2023-05-13T16:54:58+00:00 Frank Li Frank.Li@nxp.com 2023-05-01T14:36:04+00:00 a551c26e8e568fad42120843521529241b9bceec VCNL4035 register(0xE) ID_L and ID_M define as: ID_L: 0x80 ID_H: 7:6 (0:0) 5:4 (0:0) slave address = 0x60 (7-bit) (0:1) slave address = 0x51 (7-bit) (1:0) slave address = 0x40 (7-bit) (1:0) slave address = 0x41 (7-bit) 3:0 Version code default (0:0:0:0) So just check ID_L. Fixes: 55707294c4eb ("iio: light: Add support for vishay vcnl4035") Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20230501143605.1615549-1-Frank.Li@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
VCNL4035 register(0xE) ID_L and ID_M define as:

 ID_L: 0x80
 ID_H: 7:6 (0:0)
       5:4 (0:0) slave address = 0x60 (7-bit)
           (0:1) slave address = 0x51 (7-bit)
           (1:0) slave address = 0x40 (7-bit)
           (1:0) slave address = 0x41 (7-bit)
       3:0 Version code default	(0:0:0:0)

So just check ID_L.

Fixes: 55707294c4eb ("iio: light: Add support for vishay vcnl4035")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230501143605.1615549-1-Frank.Li@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: adc: stm32-adc: skip adc-channels setup if none is present 2023-05-13T16:54:57+00:00 Sean Nyekjaer sean@geanix.com 2023-05-03T16:20:29+00:00 3e27ef0ced49f8ae7883c25fadf76a2086e99025 If only adc differential channels are defined driver will fail with stm32-adc: probe of 48003000.adc:adc@0 failed with error -22 Fix this by skipping the initialization if no channels are defined. This applies only to the legacy way of initializing adc channels. Fixes: d7705f35448a ("iio: adc: stm32-adc: convert to device properties") Signed-off-by: Sean Nyekjaer <sean@geanix.com> Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com> Link: https://lore.kernel.org/r/20230503162029.3654093-2-sean@geanix.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
If only adc differential channels are defined driver will fail with
stm32-adc: probe of 48003000.adc:adc@0 failed with error -22

Fix this by skipping the initialization if no channels are defined.

This applies only to the legacy way of initializing adc channels.

Fixes: d7705f35448a ("iio: adc: stm32-adc: convert to device properties")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20230503162029.3654093-2-sean@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: adc: stm32-adc: skip adc-diff-channels setup if none is present 2023-05-13T16:54:57+00:00 Sean Nyekjaer sean@geanix.com 2023-05-03T16:20:28+00:00 9c0d6ccd7d6bbd275e390b55a3390b4274291d95 If no adc differential channels are defined driver will fail with EINVAL: stm32-adc: probe of 48003000.adc:adc@0 failed with error -22 Fix this by skipping the initialization if no channels are defined. This applies only to the legacy way of initializing adc channels. Fixes: d7705f35448a ("iio: adc: stm32-adc: convert to device properties") Signed-off-by: Sean Nyekjaer <sean@geanix.com> Link: https://lore.kernel.org/r/20230503162029.3654093-1-sean@geanix.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> 
If no adc differential channels are defined driver will fail with EINVAL:
stm32-adc: probe of 48003000.adc:adc@0 failed with error -22

Fix this by skipping the initialization if no channels are defined.

This applies only to the legacy way of initializing adc channels.

Fixes: d7705f35448a ("iio: adc: stm32-adc: convert to device properties")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20230503162029.3654093-1-sean@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>