Remove extra space between platform prefix and DRIVER_NAME in MODULE_ALIAS.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The adis16448, unlike the other chips in this family, in addition to the
hardware channels also sends out the DIAG_STAT register in burst mode
before them. Handle that case by skipping over the first 2 bytes before we
pass the received data to the buffer.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

There are a few issues with the burst mode support. For one we don't setup
the rx buffer, so the buffer will never be filled and all samples will read
as the zero. Furthermore the tx buffer has the wrong type, which means the
driver sends the wrong command and not the right data is returned.

The final issue is that in burst mode all channels are transferred. Hence
the length of the transfer length should be the number of hardware
channels * 2 bytes. Currently the driver uses indio_dev->scan_bytes for
this. But if the timestamp channel is enabled the scan_bytes will be larger
than the burst length. Fix this by just calculating the burst length based
on the number of hardware channels.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

We unfortunately can't use ~0UL for the scan mask to indicate that the
only valid scan mask is all channels selected. The IIO core needs the exact
mask to work correctly and not a super-set of it. So calculate the masked
based on the channels that are available for a particular device.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Previously, the two voltage channels had the same ID, which didn't cause
conflicts in sysfs only because one channel is named and the other isn't;
this is still violating the spec though, two indexed channels should never
have the same index.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add the scale for the pressure channel, which is currently missing.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Jonathan writes:

The usual mixed bag of fixes for IIO in the 4.1 cycle.

Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.

One core fix

* Set updated for a iio kfifo was incorrectly set to false during a failed
  update, resulting in atttempts to repeat the failed operation appearing
  to succeed.

This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.

* axp288_adc - a recent change added a check for valid info masks when
  reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
  causing a temperature of 0 to always be returned and incorrect presure
  measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
  remote CPUs. Fix an issue with the use of the power-up/power-down register
  (basically wrong polarity). Fix an issue due to the missinterpretting the
  return value from regulator_get_voltage. Add a delay before the start bit
  as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
  sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
  no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
  cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
  channel. Input checking for activity period to avoid rather unpredictable
  results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
  boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
  probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
  channel, incorrect scale on VREFP and incorrect sign on VREFN.

'channels' is allocated via kmemdup and it is never freed.

Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.

Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

According to hardware team there should be some delay after
setting channel number, start mode and before setting START.
Add a one microsecond delay for this purpose.

Fixes: 1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

regulator_get_voltage() returns a non-negative value in case of success,
and a negative error in case of error. Let's fix this.

Fixes: 1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>