Pull char / misc / IIO / and others driver updates from Greg KH:
 "Here is the char/misc/iio and other smaller driver subsystem updates
  for 7.1-rc1. Lots of stuff in here, all tiny, but relevant for the
  different drivers they touch. Major points in here is:

   - the usual large set of new IIO drivers and updates for that
     subsystem (the large majority of this diffstat)

   - lots of comedi driver updates and bugfixes

   - coresight driver updates

   - interconnect driver updates and additions

   - mei driver updates

   - binder (both rust and C versions) updates and fixes

   - lots of other smaller driver subsystem updates and additions

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (405 commits)
  coresight: tpdm: fix invalid MMIO access issue
  mei: me: add nova lake point H DID
  mei: lb: add late binding version 2
  mei: bus: add mei_cldev_uuid
  w1: ds2490: drop redundant device reference
  bus: mhi: host: pci_generic: Add Telit FE912C04 modem support
  mei: csc: wake device while reading firmware status
  mei: csc: support controller with separate PCI device
  mei: convert PCI error to common errno
  mei: trace: print return value of pci_cfg_read
  mei: me: move trace into firmware status read
  mei: fix idle print specifiers
  mei: me: use PCI_DEVICE_DATA macro
  sonypi: Convert ACPI driver to a platform one
  misc: apds990x: fix all kernel-doc warnings
  most: usb: Use kzalloc_objs for endpoint address array
  hpet: Convert ACPI driver to a platform one
  misc: vmw_vmci: Fix spelling mistakes in comments
  parport: Remove completed item from to-do list
  char: remove unnecessary module_init/exit functions
  ...

Pull hwmon updates from Guenter Roeck:
 "New drivers:
   - Lenovo Yoga/Legion fan monitoring (yogafan)
   - LattePanda Sigma EC
   - Infineon XDP720 eFuse
   - Microchip MCP998X

  New device support:
   - TI INA234
   - Infineon XDPE1A2G5B/7B
   - Renesas RAA228942 and RAA228943 (isl68137)
   - Delta Q54SN120A1 and Q54SW120A7 (pmbus)
   - TI TMP110 and TMP113 (tmp102)
   - Sony APS-379 (pmbus)
   - ITE IT8689E (it87)
   - ASUS ROG STRIX Z790-H, X470-F, and CROSSHAIR X670E (asus-ec-sensors)
   - GPD Win 5 (gpd-fan)

  Modernization and Cleanups:
   - Convert asus_atk0110 and acpi_power_meter ACPI drivers to platform
     drivers
   - Remove i2c_match_id() usage in many PMBus drivers
   - Use guard() for mutex protection in pmbus_core
   - Replace sprintf() with sysfs_emit() in ads7871, emc1403, max6650,
     ads7828, max31722, and tc74
   - Various markup and documentation improvements for yogafan and
     ltc4282

  Bug fixes:
   - Fix use-after-free and missing usb_kill_urb on disconnect in powerz
     driver
   - Avoid cacheline sharing for DMA buffer in powerz driver
   - Fix integer overflow in power calculation on 32-bit in isl28022
     driver
   - Fix bugs in pt5161l_read_block_data()
   - Propagate SPI errors and fix incorrect error codes in ads7871
     driver
   - Fix i2c_smbus_write_byte_data wrapper argument type in max31785
     driver

  Device tree bindings:
   - Convert npcm750-pwm-fan to DT schema
   - Add bindings for Infineon XDP720, Microchip MCP998X, Sony APS-379,
     Renesas RAA228942/3, Delta Q54SN120A1/7, XDPE1A2G5B/7B, Aosong
     AHT10/20, DHT20, and TI INA234
   - Adapt moortec,mr75203 bindings for T-Head TH1520"

* tag 'hwmon-for-v7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (82 commits)
  hwmon: (ina233) Don't check for specific errors when parsing properties
  hwmon: (isl28022) Don't check for specific errors when parsing properties
  hwmon: (pmbus/tps25990) Don't check for specific errors when parsing properties
  hwmon: (nct6683) Add customer ID for ASRock B650I Lightning WiFi
  hwmon:(pmbus/xdp720) Add support for efuse xdp720
  dt-bindings: hwmon/pmbus: Add Infineon XDP720
  hwmon: add support for MCP998X
  dt-bindings: hwmon: add support for MCP998X
  hwmon: (powerz) Avoid cacheline sharing for DMA buffer
  hwmon: (isl28022) Fix integer overflow in power calculation on 32-bit
  hwmon: (pt5161l) Fix bugs in pt5161l_read_block_data()
  hwmon: (powerz) Fix missing usb_kill_urb() on signal interrupt
  hwmon: (powerz) Fix use-after-free on USB disconnect
  hwmon: pmbus: Add support for Sony APS-379
  dt-bindings: trivial-devices: Add sony,aps-379
  hwmon: (yogafan) various markup improvements
  hwmon: (sparx5) Make it selectable for ARCH_LAN969X
  hwmon: (tmp102) add support for update interval
  hwmon: (yogafan) fix markup warning
  hwmon: (yogafan) Add support for Lenovo Yoga/Legion fan monitoring
  ...

We need the char/misc/iio/comedi fixes in here as well for testing

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Nobody defines struct ina2xx_platform_data. Remove platform data support
from the drivers which still have it (it's effectively dead code) and
remove the header.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://lore.kernel.org/r/20260326-drop-ina2xx-pdata-v1-1-c159437bb2df@oss.qualcomm.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Jonathan writes:

IIO: 3rd set of fixes for the 7.0 cycle.

Note that this pull is in addition to the 2nd set of such fixes that are
waiting to be picked up. Absolutely fine to queue these for the merge
window if that makes more sense.

Usual mixed back of ancient issues surfacing and newer problems.

adi,ad57770r
- Stop eating an error in read_raw.
adi,adxl313
- Check return of regmap_write() instead of ignoring it in one place.
adi,adxl355
- Fix the description of the temperature channel to be unsigned rather
  than signed.
bosch,bmi160
- Avoid use of uninitialized data.
- Fix validation of small reference voltages.
hid-sensor-rotation:
- The timestamp location in this driver has unfortunately been broken for
  a long time. Given it was correct for 6 years and then broken for the
  next 6 years, use a one off hack to duplicate it in both locations.
  The issue was as a result of the unique nature of quaternion
  representation combined with large precision resulting in an
  128 bit aligned channel.
nxp,sar-adc
- Avoid leaking a dma channel.
rfdigital,rfd77402
- Close a race between reinit_completion() and the irq happening.
ti,adc161s626
- Fix up buffer handling on big endian hosts which was broken due to
  casting of pointers to different sized integers.
- Ensure a DMA safe buffer is used.
vishay,vcnl4035
- Fix up buffer handling on big endian hosts which was broken due to
  casting of pointers to different sized integers.
vishay,veml6070
- Fix return value mess up that occurred when doing a guard() conversion.

* tag 'iio-fixes-for-7.0c' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: light: veml6070: fix veml6070_read() return value
  iio: adc: nxp-sar-adc: Fix DMA channel leak in trigger mode
  iio: accel: adxl313: add missing error check in predisable
  iio: dac: ad5770r: fix error return in ad5770r_read_raw()
  iio: accel: fix ADXL355 temperature signature value
  iio: light: vcnl4035: fix scan buffer on big-endian
  iio: adc: ti-adc161s626: use DMA-safe memory for spi_read()
  iio: adc: ti-adc161s626: fix buffer read on big-endian
  iio: dac: mcp47feb02: Fix Vref validation [1-999] case
  iio: imu: bmi160: Remove potential undefined behavior in bmi160_config_pin()
  iio: orientation: hid-sensor-rotation: add timestamp hack to not break userspace
  iio: proximity: rfd77402: Fix completion race condition in IRQ mode

Jonathan writes:

IIO: 2nd set of fixes for the 7.0 cycle

Usual mixed bag of fixes for recent code and much older issues that have
surfaced. Biggest group are continued resolution of IRQF_ONE_SHOT
being used incorrectly (which now triggers a warning)

adi,ad4062
- Replace IRQF_ONESHOT (as no threaded handler) with IRQF_NO_THREAD as
  the caller makes use of iio_trigger_poll() which cannot run from a
  thread.
adi,ade9000
- Move mutex_init() earlier to ensure it is available if spurious IRQ
  occurs.
adi,adis16550
- Fix swapped gyro and accel filter functions.
adi,adxl3380
- Fix some bit manipulation that was always resulting in 0.
- Fix incorrect register map for calibbias on the active power channel.
- Fix returning IRQF_HANDLED from a function that should return 0 or
  -ERRNO.
aspeed,adc
- Clear a reference voltage bit that might be set prior to driver load.
bosch,bno055
- Off by one channel buffer sizing. Benine due to padding prior to the
  subsequent timestamp.
hid-sensors
- A more complex fix to IRQF_ONESHOT warning as this driver had a trigger
  that was never actually used but the ABI that exposed had to be
  maintained to avoid regressions.
hid-sensors-rotation
- An obscure buffer alignment case that applies to quaternions only was
  recently broken resulting in writes beyond the end of the channel buffer.
  Add a new core macro and apply it in this driver to make it very clear
  what was going on.
honeywell,abp2030pa
- Remove meaningless IRQF_ONESHOT from a non threaded IRQ handler.
  Warning fix only.
invense,mpu3050
- Fix token passed to free_irq() to match the one used at setup.
- Fix an irq resource leak in error path.
- Reorder probe so that userspace interfaces are exposed only after
  everything else has finished.
- Reorder remove slightly to cleanup the buffer only after irq removed
  ensuring reverse of probe sequence.
microchip,mcp47feb02
- Fix use of mutex before it was initialized by not performing unnecessary
  lock that was early enough in probe that all code was serial.
st,lsm6dsx
- Ensure that FIFO ODR is only controllable for accel and gyro channels
  avoiding incorrect register accesses.
- Restrict separation of buffer sampling from main sampling rate to
  accelerometer. It is only useful for running event detection faster
  than the fifo and the only events are on the accelerometer.
ti,ads1018
- Fix overflow of u8 which wasn't big enough to store max data rate value.
ti,ads1119:
- Fix unbalanced pm in an error path.
- IRQF_ONESHOT (as no threaded handler) replaced with IRQF_NO_THREAD
  (needed for iio_trigger_poll()).
- Ensure complete reinitialized before reuse. Previously it would have
  completed immediate after the first time.
ti,ads7950
- Fix return value of gpio_get() to be 0 or 1.
- Avoid accidental overwrite of state resulting in gpio_get() only
  returning 0 or -ERRNO but never 1.

* tag 'iio-fixes-for-7.0b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (25 commits)
  iio: imu: adis16550: fix swapped gyro/accel filter functions
  iio: adc: aspeed: clear reference voltage bits before configuring vref
  iio: adc: ti-ads1119: Reinit completion before wait_for_completion_timeout()
  iio: adc: ti-ads1018: fix type overflow for data rate
  iio: adc: ti-ads7950: do not clobber gpio state in ti_ads7950_get()
  iio: adc: ti-ads7950: normalize return value of gpio_get
  iio: orientation: hid-sensor-rotation: fix quaternion alignment
  iio: add IIO_DECLARE_QUATERNION() macro
  iio: adc: ti-ads1119: Replace IRQF_ONESHOT with IRQF_NO_THREAD
  iio: imu: bno055: fix BNO055_SCAN_CH_COUNT off by one
  iio: hid-sensors: Use software trigger
  iio: adc: ad4062: Replace IRQF_ONESHOT with IRQF_NO_THREAD
  iio: gyro: mpu3050: Fix out-of-sequence free_irq()
  iio: gyro: mpu3050: Move iio_device_register() to correct location
  iio: gyro: mpu3050: Fix irq resource leak
  iio: gyro: mpu3050: Fix incorrect free_irq() variable
  iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer only
  iio: imu: st_lsm6dsx: Set FIFO ODR for accelerometer and gyroscope only
  iio: dac: mcp47feb02: Fix mutex used before initialization
  iio: adc: ade9000: fix wrong return type in streaming push
  ...

Add chip info structs and device table entries for ADRF5702 and ADRF5703
Digital Step Attenuators.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for the SARADC found on the Amlogic Meson S4 SoC.
According to the documentation and current testing, it is fully
compatible with the G12A parameter set, so we reuse
`meson_sar_adc_g12a_data` for this new compatible string.

Although the device tree fallback mechanism could handle the match,
a dedicated entry is added to ensure the userspace ABI correctly
reports the specific part name ("meson-s4-saradc"). This allows
userspace to accurately identify the exact device and maintains
consistency across different firmware types where automatic fallback
parsing might be problematic.

Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Nick Xie <nick@khadas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The SHIFT13mi or SHIFTbook tablet device by the German manufacturer
SHIFT contains an STM LSM6DSO IMU declared in the DSDT with the
hardware ID SMOCF00. Add this ID to the ACPI match table so that the
driver binds correctly to this device.

WHO_AM_I register returns 0x6c, confirming LSM6DSO.

Signed-off-by: Milan Misic <twoexem@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

veml6070_read() computes the sensor value in ret but
returns 0 instead of the actual result. This causes
veml6070_read_raw() to always report 0.

Return the computed value instead of 0.

Running make W=1 returns no errors. I was unable
to test the patch because I do not have the hardware.
Found by code inspection.

Fixes: fc38525135dd ("iio: light: veml6070: use guard to handle mutex")
Signed-off-by: Aldo Conte <aldocontelk@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>