linux-stable.git/drivers/i2c, branch v6.4.4

usb: typec: ucsi: Mark dGPUs as DEVICE scope

2023-07-19T14:36:55+00:00

commit a7fbfd44c0204f0629288edfd0d77829edb4a2f8 upstream.

power_supply_is_system_supplied() checks whether any power
supplies are present that aren't batteries to decide whether
the system is running on DC or AC.  Downstream drivers use
this to make performance decisions.

Navi dGPUs include an UCSI function that has been exported
since commit 17631e8ca2d3 ("i2c: designware: Add driver
support for AMD NAVI GPU").

This UCSI function registers a power supply since commit
992a60ed0d5e ("usb: typec: ucsi: register with power_supply class")
but this is not a system power supply.

As the power supply for a dGPU is only for powering devices connected
to dGPU, create a device property to indicate that the UCSI endpoint
is only for the scope of `POWER_SUPPLY_SCOPE_DEVICE`.

Link: https://lore.kernel.org/lkml/20230516182541.5836-2-mario.limonciello@amd.com/
Reviewed-by: Evan Quan 
Tested-by: Evan Quan 
Signed-off-by: Mario Limonciello 
Reviewed-by: Heikki Krogerus 
Reviewed-by: Sebastian Reichel 
Acked-by: Andi Shyti 
Signed-off-by: Wolfram Sang 
Signed-off-by: Greg Kroah-Hartman

i2c: xiic: Don't try to handle more interrupt events after error

2023-07-19T14:36:50+00:00

[ Upstream commit cb6e45c9a0ad9e0f8664fd06db0227d185dc76ab ]

In xiic_process, it is possible that error events such as arbitration
lost or TX error can be raised in conjunction with other interrupt flags
such as TX FIFO empty or bus not busy. Error events result in the
controller being reset and the error returned to the calling request,
but the function could potentially try to keep handling the other
events, such as by writing more messages into the TX FIFO. Since the
transaction has already failed, this is not helpful and will just cause
issues.

This problem has been present ever since:

commit 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")

which allowed non-error events to be handled after errors, but became
more obvious after:

commit 743e227a8959 ("i2c: xiic: Defer xiic_wakeup() and
__xiic_start_xfer() in xiic_process()")

which reworked the code to add a WARN_ON which triggers if both the
xfer_more and wakeup_req flags were set, since this combination is
not supposed to happen, but was occurring in this scenario.

Skip further interrupt handling after error flags are detected to avoid
this problem.

Fixes: 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
Signed-off-by: Robert Hancock 
Acked-by: Andi Shyti 
Signed-off-by: Wolfram Sang 
Signed-off-by: Sasha Levin

i2c: imx-lpi2c: fix type char overflow issue when calculating the clock cycle

2023-06-23T10:58:24+00:00

Claim clkhi and clklo as integer type to avoid possible calculation
errors caused by data overflow.

Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver")
Signed-off-by: Clark Wang 
Signed-off-by: Carlos Song 
Reviewed-by: Andi Shyti 
Signed-off-by: Wolfram Sang

i2c: qup: Add missing unwind goto in qup_i2c_probe()

2023-06-23T10:58:24+00:00

Smatch Warns:
	drivers/i2c/busses/i2c-qup.c:1784 qup_i2c_probe()
	warn: missing unwind goto?

The goto label "fail_runtime" and "fail" will disable qup->pclk,
but here qup->pclk failed to obtain, in order to be consistent,
change the direct return to goto label "fail_dma".

Fixes: 9cedf3b2f099 ("i2c: qup: Add bam dma capabilities")
Signed-off-by: Shuai Jiang 
Reviewed-by: Dongliang Mu 
Reviewed-by: Andi Shyti 
Signed-off-by: Wolfram Sang 
Cc:  # v4.6+

i2c: sprd: Delete i2c adapter in .remove's error path

2023-06-07T10:29:58+00:00

If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.

So only skip clk disabling if resume failed, but do delete the adapter.

Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Uwe Kleine-König 
Reviewed-by: Andi Shyti 
Signed-off-by: Wolfram Sang

i2c: mv64xxx: Fix reading invalid status value in atomic mode

2023-06-05T10:22:30+00:00

There seems to be a bug within the mv64xxx I2C controller, wherein the
status register may not necessarily contain valid value immediately
after the IFLG flag is set in the control register.

My theory is that the controller:
- first sets the IFLG in control register
- then updates the status register
- then raises an interrupt

This may sometime cause weird bugs when in atomic mode, since in this
mode we do not wait for an interrupt, but instead we poll the control
register for IFLG and read status register immediately after.

I encountered -ENXIO from mv64xxx_i2c_fsm() due to this issue when using
this driver in atomic mode.

Note that I've only seen this issue on Armada 385, I don't know whether
other SOCs with this controller are also affected. Also note that this
fix has been in U-Boot for over 4 years [1] without anybody complaining,
so it should not cause regressions.

[1] https://source.denx.de/u-boot/u-boot/-/commit/d50e29662f78

Fixes: 544a8d75f3d6 ("i2c: mv64xxx: Add atomic_xfer method to driver")
Signed-off-by: Marek Behún 
Signed-off-by: Wolfram Sang

i2c: designware: fix idx_write_cnt in read loop

2023-06-05T09:58:20+00:00

With IC_INTR_RX_FULL slave interrupt handler reads data in a loop until
RX FIFO is empty. When testing with the slave-eeprom, each transaction
has 2 bytes for address/index and 1 byte for value, the address byte
can be written as data byte due to dropping STOP condition.

In the test below, the master continuously writes to the slave, first 2
bytes are index, 3rd byte is value and follow by a STOP condition.

 i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D1-D1]
 i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D2-D2]
 i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D3-D3]

Upon receiving STOP condition slave eeprom would reset `idx_write_cnt` so
next 2 bytes can be treated as buffer index for upcoming transaction.
Supposedly the slave eeprom buffer would be written as

 EEPROM[0x00D1] = 0xD1
 EEPROM[0x00D2] = 0xD2
 EEPROM[0x00D3] = 0xD3

When CPU load is high the slave irq handler may not read fast enough,
the interrupt status can be seen as 0x204 with both DW_IC_INTR_STOP_DET
(0x200) and DW_IC_INTR_RX_FULL (0x4) bits. The slave device may see
the transactions below.

 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1794 : INTR_STAT=0x204
 0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x1790 : INTR_STAT=0x200
 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
 0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4

After `D1` is received, read loop continues to read `00` which is the
first bype of next index. Since STOP condition is ignored by the loop,
eeprom buffer index increased to `D2` and `00` is written as value.

So the slave eeprom buffer becomes

 EEPROM[0x00D1] = 0xD1
 EEPROM[0x00D2] = 0x00
 EEPROM[0x00D3] = 0xD3

The fix is to use `FIRST_DATA_BYTE` (bit 11) in `IC_DATA_CMD` to split
the transactions. The first index byte in this case would have bit 11
set. Check this indication to inject I2C_SLAVE_WRITE_REQUESTED event
which will reset `idx_write_cnt` in slave eeprom.

Signed-off-by: David Zheng 
Acked-by: Jarkko Nikula 
Signed-off-by: Wolfram Sang

i2c: mchp-pci1xxxx: Avoid cast to incompatible function type

2023-06-05T08:43:45+00:00

Rather than casting pci1xxxx_i2c_shutdown to an incompatible function type,
update the type to match that expected by __devm_add_action.

Reported by clang-16 with W-1:

 .../i2c-mchp-pci1xxxx.c:1159:29: error: cast from 'void (*)(struct pci1xxxx_i2c *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
         ret = devm_add_action(dev, (void (*)(void *))pci1xxxx_i2c_shutdown, i2c);
                                    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 ./include/linux/device.h:251:29: note: expanded from macro 'devm_add_action'
         __devm_add_action(release, action, data, #action)
                                   ^~~~~~

No functional change intended.
Compile tested only.

Signed-off-by: Simon Horman 
Reviewed-by: Horatiu Vultur 
Reviewed-by: Andi Shyti 
Reviewed-by: Tharun Kumar P
Signed-off-by: Wolfram Sang

i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate"

2023-06-05T08:39:11+00:00

There is a spelling mistake in a comment. Fix it.

Signed-off-by: Christian Heusel 
Signed-off-by: Wolfram Sang

i2c: gxp: fix build failure without CONFIG_I2C_SLAVE

2023-05-03T15:27:29+00:00

The gxp_i2c_slave_irq_handler() is hidden in an #ifdef, but the
caller uses an IS_ENABLED() check:

drivers/i2c/busses/i2c-gxp.c: In function 'gxp_i2c_irq_handler':
drivers/i2c/busses/i2c-gxp.c:467:29: error: implicit declaration of function 'gxp_i2c_slave_irq_handler'; did you mean 'gxp_i2c_irq_handler'? [-Werror=implicit-function-declaration]

It has to consistently use one method or the other to avoid warnings,
so move to IS_ENABLED() here for readability and build coverage, and
move the #ifdef in linux/i2c.h to allow building it as dead code.

Fixes: 4a55ed6f89f5 ("i2c: Add GXP SoC I2C Controller")
Signed-off-by: Arnd Bergmann 
Reviewed-by: Nick Hawkins 
Signed-off-by: Wolfram Sang